Question about Kitchen Ranges

1 Answer

When I power up my Kenwood TS 870s I get 1400.00 for about 2 seconds then "ERR FE" on the sub display; and that's all it will do. Any suggestions? Ken VE3YK VE3YK@sympatico.ca

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

BUY AN ICOM PRO 3 & GET RID OF THAT KENWOOD JUNK

Posted on Nov 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset error codes


Dual Fuel Range Error Code 07 ' FAQ ' Sub-Zero and Wolf

www.subzero-wolf.com/.../dual-fuel-range-error-code-07

Sub?ZeroCore Issue: Dual Fuel Range error code 7; ERR 07 displays on Dual Fuel; Error 07 on control panel of Dual Fuel ... Convection Steam Oven Error Code E75.

L Series Built-In Oven Error Code COMM ERR ' FAQ ' Sub ...

www.subzero-wolf.com/.../l-series-built-in-oven-error-code-co...

Sub?ZeroCOMM ERR displayed on an L Series Built-In Oven indicates a communication error.Reset the unit's power at the circuit breaker. Turn the unit back on to see if ...

WWD30 Warming Drawer Error Code 40 - Sub-Zero and Wolf

www.subzero-wolf.com/.../wwd30-warming-drawer-error-cod...

Sub?ZeroError 40 on a Wolf Warming Drawer. Steps to Verify Issue: With error 40 on WWD30 warming drawer try the following before calling service: ... x. PF Error Code on Warming Drawer ... Whether you're shopping for appliances or have questions about those you already own, we've got the resources you need. ... Wolf Cooking.

Wolf DF304 beeping after turning off the oven - The Kitchen ...

appliantology.org > ... > The Kitchen Appliance Repair Forum

Dec 25, 2015 | Wolf Range Kitchen Ranges

4 Answers

Was low temp roasting of ribs in Jenn Air JMW9530AAB convection oven. Heat webt ofand stove started to beep and displayed "-F7-". Cancel failed to do anything. Shut power off and when turned...


The electronic control may not be set correctly. If the control is not programmed correctly the oven will not start and you will usually hear a series of beeps instead of the microwave starting. See your Use & Care Guide

Aug 09, 2008 | Jenn-Air Kitchen Ranges

Tip

Power off for 5 Minutes


We had this display failure twice within the last 2 years on our 6 year old rbd305pds14 range. The display went blank, but all other button functions (light, beeps etc) remained operational.<br /><br />Each time I turned off the main breaker power for about 5 minutes. <br /><br />While power is off, I also (lightly) pressed and held each button on the panel for about 2 seconds - This was to further eliminate residual power due to capacitance/inductance effects that might be retained in sub-components in the circuit. (This might not be necessary, but my electronics maintenance training had us do this when the circuit is not well known - and it gives you something to do during the 5 minutes!)<br /><br />Both times this has worked. So far I have not needed to access the control panel and re-seat the ribbon cable.<br /><br /> Note, Following the manual's advice of turning off the breaker for 30-60 seconds did NOT work, which tells me there likely is some C/I effect in the circuit, (possibly due to a subtle ground loop??, but that is for an electrical engineer to determine.)<br /><br />Sincerely hope this helps you.<br /><br />

on Apr 16, 2011 | Kitchen Ranges

1 Answer

The digital display for a Magic Chef gas oven reads "5 A6", what does that mean?


Your range is probably in the Sabbath mode. The error code shown on the display is"Sab", not "5ab".

To disable the Sabbath mode push and hold the Clock pad for 3 seconds.

Mar 21, 2013 | Kitchen Ranges

1 Answer

Kitchen Aid range: error code F1E0 replace oven UI


F1-E0 = EEPROM communication error



1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock). If you bought this control board used I am afraid it is bad. That error is only for a bad control board.
Here is a new board you may purchase. It is a little expensive but the supplier has a 365 day, any reason, any part return policy and you can be certain that you have a quality part.


Nov 10, 2012 | Kitchen Ranges

1 Answer

What's your problem?Oven cuts off after a minute, and display shows "F-2" or F-3 on digital display. Kenmore model #911455881A


Hello Again,

On this second question i see the model number, the part number for that sensor is WB 21X5301

Oct 12, 2011 | Kitchen Ranges

1 Answer

Temperature will not work.


Try powering the unit down...open both breakers for half an hour and then repower.  If this doesn't help, you should evaluate the cost of a new assembly

Sep 09, 2008 | KitchenAid KESC307 Electric Kitchen Range

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...