Question about Samsung HLR5667W 56" Rear Projection HDTV

1 Answer

My T.V. will not turn off. The last repairman bypassed the swith on the back door of the T.V. Should I just repklace the little blue switch on the back of the T.V.?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

That blue switch is in place to make sure that the back of the TV is closed properly. It prevents the TV from being turned on when the back is removed. It would not be keeping the TV from turning off. Replacing that switch would not solve your problem.

Posted on Oct 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lost controller. how to use or by pass on off swith


Solder a jumper wire across the back of the switch, this will bypass the switch and the speakers will always be turned on. Turn off the speakers by unplugging the power cord, or with the switch on the surge protector that I hope you have.

Feb 20, 2014 | Dell HK395 Computer Speakers

1 Answer

2003 nissan altima took window down and would not go back up.30min.latter it worked.today forgot about it and it did it again.is the switch bad?how can i get the window up for now without the switch?


This may be the switch ,but most times its a motor, try to hold the swith in the up postion and bang on inside of door toward the midlle and bottom while holding switch, ig that doesnt work try to push swith for window to go up useing a little force and wiggle.the best way to find the problem would be to test motor for power and ground while operating the switch.

Jun 15, 2010 | 2003 Nissan Altima

1 Answer

Canon G3 camera just stopped working completely


Do you have a way to test the battery and you know it's ok?

Those batteries have built-in protection circuitry that can cut out or turn off the battery entirely if it detected a problem like a short circuit, etc. And it may not get over it.

Try a 2nd battery or the AC power adapter directly.

Also check that the 3 little pins in the camera DC input jack are intact, straight, and not touching each other.

Some camera's won't turn on if the memory card door is open or the card is ejected but I tested that on my G3 and it still turns on either way.

Ah.... and lastly... there is a little electrical limit switch connected to the battery cover door that disables the camera if the battery door is open. It gets pressed by a small plastic piece attached to the battery cover when you close the battery door. If the plastic piece or the tiny, recessed switch has an issue then the camera won't turn on The switch could be bypassed internally (not easy to do) if that was the problem.

Look for a tiny, thin, black plastic switch about as thin as a staple down in a recessed hole (slot) near the battery cover hinge. Try gentle pushing the battery closed switch "over" a little. You can tell which way to push by observing how the battery door slides into position as you close it. I was able to turn on my camera with the door open by doing this.
The switch is very tiny, don't break it.

If the battery door isn't closing all the way that would also cause the same issue.

Feb 18, 2010 | Canon PowerShot G3 Digital Camera

1 Answer

The doors are all shut, but the dome light is not going off. indicator light showing door(s) open will not go off.


Most likely a faulty door jam switch. either this will be a little button near the door hinges, or can be attached to the door latch mechanism. the latter is a little more difficult to test because it can involve pulling the door panel apart. Try to find each switch and disconnect it from the circuit if possible to see if the light goes out. or try pulling out the switches and checking them to see if they are functioning properly with a continuity check on a multimeter. if all switches check out fine, the next steps are a little more advanced. Check the wiring from the switches for shorts between the wires that could be bypassing the switch all together giving it constant power. and the last, in rare cases it can be caused by a faulty body control module or similar electrical systems computer.

Jan 20, 2010 | 1998 Ford Taurus

2 Answers

I had a repairman come in yesterday. Said my


12 o'clock red...4 o'clock blue...3 o'clock white .( the white , has the smaller terminal )

Oct 24, 2009 | Whirlpool GS6SHAXLQ 25.5 Cubic Foot Side...

1 Answer

My oven turns on but won't heat up to the temperature i set it at. that last time i had it repaired the repairman simply reset the oven. how do i do that?


I had the same problem after auto-cleaning my oven just before Thanksgiving. The cause was overheating...and the tripping of a heat sensor switch.

The switch (reset button) is located about 3 inches behind the door locking mechanism.

Removing the front panel (4 screws) that the door lock sticks through exposes the switch. Just push the little red button & your are back in business!

Oct 08, 2009 | Dacor ECD230 Epicure Electric Double Oven

4 Answers

Jensens UV9 By pass the brake


hook up the ground with the pink and when you are in am/fm mode hit the dvd set up button on the remote, input the no. 5, 4, 3, 2, 1, and 0 make sure it beeps after every no. has been pressed. then it should bring up the hidden menu select the hammer option and turn on the brake bypass option. your done.

i took this from the uv8 brake bypass. it works on the uv9.

Nov 12, 2008 | Car Audio & Video

1 Answer

Installing cd players


YOU HAVE THE ILLUMINATION WIRE HOOKED INTO THE RADIO

Oct 02, 2008 | 1999 Chevrolet Tahoe

2 Answers

Whirlpool Ler 7620 Lwo


Thermal fuse for the motor is out. It's on inside on the back wall. look for the two blue wires connecting to it.

Sep 05, 2008 | Whirlpool LER8648P Electric Dryer

1 Answer

The fuel pump has been changed, however it does not pump fuel. A by-pass swith was installed and it works. What makes this happen. Could it be the ignition switch causing the problem. When the by-pass...


Chances are the fuel pump relay has died, and the bypass switch is turning it on in the absence of the relay. Replace your fuel pump relay and you should be able to get rid of the bypass switch.

Aug 05, 2008 | Mitsubishi Galant Cars & Trucks

Not finding what you are looking for?
Samsung HLR5667W 56" Rear Projection HDTV Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74383 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...