Question about Haier hwr10xc6 Air Conditioner

21 Answers

E1 error code displays when unit is plugged in

Posted by on

  • 11 more comments 
  • DePayne Jun 02, 2008

    Air conditioner will not turn on. Error code E1 is displayed and nothing happens. When you press the buttons you hear 2 beeps that that's it. It's about a year old and worked last year.

  • Cordova Diving Jun 05, 2008

    Two days ago, the unit quit working and displayed the E1 error code. I unplugged the unit and let it sit for 10 minutes. When I plugged it back in, it worked fine until this afternoon. Now the unit has stopped working and displays the E1 error code and unplugging it has no effect.

  • GlowinFalkor Jun 06, 2008

    Mine does the same thing. I can't find what it means and it's driving me nuts. If anyone can figure it out, please please tell us!

  • Anonymous Jun 23, 2008

    E1 comes up when pluged in but works with remote

  • laurendj2 Jul 06, 2008

    I have the same E1 error message and my remote is broken. What do I do?

  • ewpiii Jul 10, 2008

    I too have this issue. I have the Haier HWR12XC3 unit which was donated to us by my wife's father. Very hot in the house now. I get the E1 error. I tried to un-stick some buttons that may have seemed stuck. The "start" button seemed stuck but I can get it unstuck by tapping the panel next to the button. Still no fix. I also tried the unplug, plug in while holding the on/off button. Unplug, let stand 5 minutes, plug back in. Still no fix.



    Does anyone have a remote i can buy? I hurting over here. Thanks: e3

  • Anonymous Jul 10, 2008

    I also had the same problem. I found my remote and pointed it at the ac to turn on and it worked!!!. You need to find that remote.

  • Anonymous Jul 22, 2008

    I get ei error. Reset does not work and remote is broken

  • surama Aug 09, 2008

    Quick solution to the E1 display problem - the remote will still work the AC.

  • Fran Kubilik Aug 20, 2008

    I just had the same problem no an hour ago. E1 showed on display, and none of the buttons on the AC worked, not even the power button.

    SOLUTION:
    In the past, I've noticed that my universal remote sometimes changes something on my AC when I'm trying to change something on the VCR. (My AC is in the living room.

    Well, I saw that the buttons on the AC wouldn't work no matter what I do. So I go get my universal remote, press the DVD/VCR mode button at the top, then just start pressing random buttons until something happened. I've got it now. I can control everything on the AC with it:

    The remote is a 'One For All' URC-3021B00

    The buttons are as follows:
    rewind=power on/off
    pause= timer on/off
    4=low/high
    5=temperature up
    9=temperature down
    8=fan/cool

    Here is the remote:
    http://www.oneforall-na.com/remote.php?t...

    Hope this helps.


  • Anonymous Sep 06, 2008

    the remote doesn't work nor does my tv/dvd remote

  • Anonymous May 25, 2009

    plugged ac unit in and it will not come on it just has the display E1... How do i fix this?

  • daddys_gi933
    daddys_gi933 Jul 23, 2012

    Air conditioner will not turn on. Error code E1 is displayed and nothing happens. When you press the buttons you hear 2 beeps that that's it. It's about a year old and worked this year.

×

21 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I just had the same problem no an hour ago. E1 showed on display, and none of the buttons on the AC worked, not even the power button.

SOLUTION:
In the past, I've noticed that my universal remote sometimes changes something on my AC when I'm trying to change something on the VCR. (My AC is in the living room.

Well, I saw that the buttons on the AC wouldn't work no matter what I do. So I go get my universal remote, press the DVD/VCR mode button at the top, then just start pressing random buttons until something happened. I've got it now. I can control everything on the AC with it:

The remote is a 'One For All' URC-3021B00

The buttons are as follows:
rewind=power on/off
pause= timer on/off
4=low/high
5=temperature up
9=temperature down
8=fan/cool

Here is the remote:
http://www.oneforall-na.com/remote.php?type=URC%203021

Hope this helps.

Posted on Aug 20, 2008

  • Lindsey Alan Jul 07, 2013

    What type of VCR did you have the remote programmed for?

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I'm having the same problem with the HWR08cx7. I called Tech Support at Haier and was told that this error code usually means that the control board thinks that a button is pushed in. The suggested fix was to "play around with the buttons and see if they unstick." The unit is less than 8 months old but the WILL NOT exchange/repair without the original receipt. Every other company honors thier warranty based on the serial number - doesn't matter about the receipt. Haier refused to honor the warranty at all. Will be contacting their corporate office and also the corporate office for Wal-Mart as that is where I purchased the unit. I suggested that Haier put a sticker on the outside of the units warning that they were "disposable" air conditioners . . . and not to expect any quality to the unit at all.

Posted on Jun 12, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

E-1 Ok i just fixed my HWR 08 XC___ these things should work on most all touch panel models. Note some slight skills required. Ok 08= 8,000 btu 06= 6,000btu exct "size"
Ok Code E-1 = electrical problem "yes"
Mine first started had to be set low and read a lower temp than the room "coils dirty" then week later it showed E-1 and an hour later would trip the plug breaker. Root cause Dirty Coils "evaporator inside" can get ice from reduced air flow making ice n water n throwing drips. when to much of it floods electronics box and faults main to E-1. -drain clean and use remote. ok now to fix other stuff "unplug" remove filter and front cover 2 screws side 2 under filter. Do coils look cruddy ok, sprayed my coils with "gunk engine cleaner" with unit on side so electrics were up and rinsed with thumb over hose for fan spray from two feet away,now though you must first remove the snap in control panel "squeeze tabs and then its metal mount cover for its internal plug 2 screws one is in foam seal then lift and pivot."has tabs" don't wet the electrics or the plug breaker " "see the silver cans in the electric box"capacitors they hold a high voltage charge" stay away. Ok now clean and spray off the rear outside coils. then when done, tilt and and then u must even flip it over till all water is out, "Yeup i got wet too"..now dry electrics for an hour with hair dryer on low and then dry control panel back side on low 15 mins, now exercise touch buttons gently then dry them again. air dry assembled unit a day in sun to be safe
The cause of this "not so fun project" is plain old dirt and water build up a shure sign of this is unit seems to vibrate more or rumble "crud on one side of fans from stopping in puddle when unit is off and drain is clogged or unit not level or slops to inside.
Now with every thing dry, use a ground fault outlet first to test how dry you got it, and have a Firemen and a Paramedic helping you...Now hold the on button and plug it in. "good luck" if no go try any units remote most are quite similar...PS remember the E-1 unit most likely still works fine "Tarzan"

Posted on Jul 13, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

We had this same problem...none of the below helped out. We have a Haier Brand. We were able to start it once but after that the E1 Error wouldn't clear and prevented us from using.

It appears that after 720 hours of use the E1 Error comes up as a reminder to clean the filter the filter. Although as in our case the E1 Error never cleared...below is what helped us out in clearing this code...this was for a Sharp but worked fine for our Haier Brand.

1. Power down the air conditioner using the "power" button on the front
panel.
2. Unplug the air conditioner from the wall socket.
3. Hold the front panel "power" button down and plug the air
conditioner in. Continue to hold the power button down as the machine
goes through a brief test sequence (fan & compressor each come on
briefly, etc). There is a "beep" sound at the end of the test sequence,
and the machine will be off. At this point, you can release the power
button.
4. Unplug the air conditioner.
5. Plug the air conditioner back in.
6. Congratulations! You should now be able to operate the air
conditioner normally for another 720 hours, but only if you followed
the instructions above EXACTLY.

Posted on Aug 02, 2009

  • grjames
    grjames Jul 04, 2012

    THANK YOU !!

    This worked exactly as described. You saved me from almost throwing this unit away. I was 2 minutes away from doing until persistence led me to the interwebs.

  • jmg62
    jmg62 Sep 05, 2012

    THANK YOU TOO! I through one Haier away because of this SAME PROBLEM. I though: "Who would have a problem like this? No company would sell a product with all these problems." Sure enough! Thank you so much - I'm glad I looked! I woulda thrown this one out too and gone and bought a new one. I should send you half the money if I'd gotten another one - I'd be out big time - they're scarce this time of year - and never knew! Haier should've sent something out. I don't think I'd buy another one of their products.

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

The E1 problem could be as simple as wet wires. If the problem happen after you emptied out water or after you had an ice build up. You may just have some wires that need to dry. Take off the front panel and wait. Then try to plug it in again and test it out. That worked for me

Posted on Jul 28, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

My E-i error was due to water in the control panel/ Like the top post, the trick is some disassembly, take off the interior radiator shroud with filter (two screws on sides), clean the fins, why not since you are in there. unscrew the circuit board. bust out a hair dryer and dry things off. real good! remember to push the buttons while using a hair dryer, the water is inside the buttons after all. after 15 minutes and a couple of trial plug-ins, things were back to normal. Woot! reassemble and enjoy. -B

Posted on Jul 25, 2010

  • Scott Weir
    Scott Weir Jun 18, 2014

    Not exactly, but by suggesting along with others that the problem likely had to do with the control panel it encouraged me to take it apart, as I have been doing for 60 years. John Muir suggested the same in the "VW Idiot Book." Sure enough, there was a bug on the circuit board, or the remains of one. Contact cleaner and a toothbrush and all well. This has happened to me before.

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I brought one of those giant universal remotes from kmart. although the thing didnt work for my direct tv receiver, the DVD function controlled my haier air conditioner perfectly. I got the e1 error early this morning, 7/24/2008 and with the 10 bucks i spent on the piece of **** that didnt work the way i wanted it too, it saved me a lot of time and trouble. Also, some cheap universal remotes (with some tinkering with the codes) can be compatible with air conditioners. Try it, or you can take the thing apart or pay 10x the amount for it to be fixed. Let me know at lingling314@gmail.com if it works for you..

Posted on Jul 24, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

JUST HAD THE SAME PROBLEM,I WAS GO NUTS.JUST USE THE REMMOTE, IT FIXED THE PROBLEM.

Posted on Jun 30, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I had same problem with E1 showing up and disabling the touch pad .I took front cover off and unsnapped the touch pad from frame of AC and took out the 5 mounting screws and CHECKED each of the switches to make sure that they free ,while disassembled I plugged it back in to see if that cured the problem and IT DID , I reassembled touch pad assembly then cleaned the dust off fins and cover .I guess I am good for another 720 hours of COLD AIR . THANKS for the HELP.

Posted on Jul 14, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hey, thanks everybody. The Little Jesus prayer to find the remote - and it worked perfectly. Try this if you can...

Posted on Jun 13, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I cleaned my Haier unit today for the first time since purchasing it in 2002. I've been having issues in the past few weeks w/ water leaking out of the unit & a knocking noise that would come & go. When I tried to turn it on, it would not do anything. After reading some of the above tips, I took it apart again and used a hair dryer & made sure there was no moisture whatsoever in the unit. I tried it again & it works like a charm. I know they usually last 5-10 years, so I'll consider having mine for 14 years a success. And I will now complete yearly maintenance until it dies in me.

Posted on Aug 13, 2016

  • Aaron Kirk
    Aaron Kirk Aug 13, 2016

    An E1 code did come on & I do not have the remote it came with & I tried to use a universal remote without success.

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

More on the E1 error: When I opened up my Haier ESA412K-L (12,000 BTU) for its annual de-bugging, instead of one dead roach I found two live ones! (This is the original "bug in the machine," at least in computer legend.) I've had this problem with electronic controls before, and generally brushing off loose roach parts and maybe spraying a little contact cleaner does the trick. This time, after spraying the contact cleaner and scrubbing the "wire" side of the board I added a little Raid bug poison. Bad idea: The Raid is conductive, AND it gums up the board. More contact cleaner, still E1. After taking the board out and cleaning the component side and a couple more similar rounds, I unplugged it and got it under a strong light. I found little streaks left by the Raid and the toothbrush (verifying they were ON the "printed" wires rather than gaps in them by scraping), and also several other little areas that looked suspiciously like roach droppings across two or more conductors. After several more squirts of contact cleaner and meticulous scrubbing of dirty areas with a Q-tip, I reinstalled the board and it worked normally. My unit does not seem to require plugging it in while holding the Power button in. Chances are, most of these units work very similarly, and I know from experience that roaches like circuit boards, though I don't know why. None of this requires any real technical knowledge, just caution, contact cleaner, and very careful cleaning on both side of the board.

Posted on May 11, 2015

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When i strat my air condetioner its not work its just show E1 error

Posted on Nov 04, 2012

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a haier air condintioner that fits in my window i dont have the problums listed above .. i got this air condtioner from my grandpa. he lost the remote to it and without one all yoy can do is turn the thing off and on..when i turned it on, its on a fan setting and low speed. i really want to get it to go high speed and on cool. there anrt any other butten but then power switch, im a girl and dnt have a clue on how to go about fixing it so if any one has any suggestions please let me know.

Posted on Aug 23, 2010

Hi all. I had the same exact problem with the E1 message and the power button sticking. None of the buttons on the AC now work - the reset button and test button did not work. HOWEVER for some reason, that remote control turns it on! You've got to find that remote, it seems to be the only way. So weird.

Posted on Sep 06, 2008

Heres what i did just got the problem 'E1' after a power outage. Hold ALL the buttons in on the panel for a few seconds and then use the remote to switch things, after that it should work. Or it worked for me....I also punched it a few times

Posted on Aug 06, 2008

I had same problem. Using the remote powered it on.

Posted on Jun 29, 2008

Haier Customer Support indicated to me that an E1 code indicates an internal electrical problem.

They told me to return it to the store for an exchange.

Posted on Jun 23, 2008

This won't fix it but try using the remote.

Posted on Jun 10, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The Universal remote thing above works. I Have a remote Given to me by my cable provider. The provider is mediacom. I don't know how in the world this happend but all the controls listed above worked.

Posted on Jul 13, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Take the control panel (red) one and plug it back in and then you will have power again..

Posted on Jun 25, 2010

4 Suggested Answers

mattozan
  • 555 Answers

SOURCE: E1 error code

You can contact Haier Technical Support here to open a support case for this error.

Posted on Jun 05, 2008

  • 330 Answers

SOURCE: Error code

Do you still the warranty for this unit? maybe you should contact the company which you bought the unit.

Posted on Jul 03, 2008

  • 11 Answers

SOURCE: samsung AQV12m e1 error code

Check the wiring. If it's okay, reset by switching the power from the outside unit off for approx. 1 minute.

Posted on Sep 13, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error E1 for washing machine


Lots of info on E1 for different makes.

  • How to repair a Samsung washing machine with error code E1 ... https://www.quora.com/How-do-I-repair-a-Samsung-washing-machine... How do I repair a Samsung washing machine with error ... If your Samsung Washing Machine is showing error code E1 then ... How do I clear bosch washing machine error ...
  • E1 error in washing machine? ' Yahoo Answers https://in.answers.yahoo.com/question/index?qid=20131129013237AA7oiKP
    • RESOLVED
    • 7 POSTS
    • 6 TOTAL ANSWERS
    2013-11-29 · E1 error in washing machine? ... Haier washing machine error code E1? LG Wave Series Washer LE error message? Washing machine error code? ...
  • My washing machine is displaying an error code. What does ... www.samsung.com/my/support/skp/faq/1033803 My washing machine is displaying an error ... E1. Water supply error. ... · Check that the level of the drain hose is not lower than the base of the washing machine.
  • Related searches for Error E1 for washing machine
  • Samsung Washing Machine 4E and E1 Fault - Help & Advice https://www.northlondonappliancerepairs.co.uk/error-codes/samsung...
    • 4.3/5
    • 46 RATINGS
    Samsung Washing Machine 4E and E1 Fault. Samsung washing machine Not filling in allocated time error code 4E and E1 Fault.
  • Help & Troubleshootings - Haier ZA Products Website www.haier.com/za/help_and_troubleshootings/faq/washing_machine Help & Troubleshootings. ... Too much water in the washing machine ... Error Code-control panel display "E1" Question : Error Code-control panel display "Lock"
  • Samsung washing machine error code 4E and E1 Fault Not ... www.youtube.com/watch?v=cFlnxeB0P0g
    • BY HOW-2-REPAIR.COM
    • 9 MIN
    • 19K VIEWS
    2015-11-24 · Video embedded · ... machine-error-code-4e-and-e1-fault-not-filling-in-allocated-time/ Samsung washing ... Samsung washing machine error code 4E and E1 ...
  • Samsung washing machine error code 4E, E1, Fault Not filling www.how-to-repair.com/help/samsung-washing-machine-error-code-4e... Samsung washing machine Not filling in allocated time error code 4E and E1 Fault This is essentially a fill timeout error which will normally mean that either the ...
  • Hoover error code E1 - White Goods Help www.whitegoodshelp.co.uk > ... > Washing Machine Error Codes Hoover error code E1. ... You need to watch the washing machine to see when it aborts to get an idea which of the three areas to look at.

  • Jul 01, 2016 | Washing Machines

    3 Answers

    E1 error code displays when unit is plugged in I have a wall unit with about 10,000 BTU capacity. Two days ago, it quit working and displayed the E1 error code. I unplugged the unit, let it sit for 10...


    highly annoying issue error code E1. After hours
    of fan operation, the error code E1 will appear on the seven segment
    LED temperature display. This error code is intended as a reminder for
    the user to clean the air filter. However, because the procedure
    outlined in the user manual does not clear this error code as
    indicated, and the appliance has a nonvolatile memory that cannot be
    reset by simply unplugging it, the user of the appliance will become
    mightily frustrated, standing in potentially sweltering heat watching
    the appliance repeatedly shut down in the midst of operation with the
    "E1" display flashing.

    Believe it or not, that is what it does: if you unplug it to remove the
    "E1" code from the display, and plug it back in and re-start it, it
    will simply run for anywhere from a few minutes to a few hours, and
    then merrily shut down again with the same flashing "E1" code.

    So you will come home to a hot bedroom, living room, etc. unexpectedly,
    and you will NOT be amused, as I was not.

    Many people at this point, having put the manual under the canary or
    some such, will simply return the unit and never buy another Sharp air
    conditioner. But for the tech-savvy and search-adept, I offer the
    following procedure to clear the nefarious E1 indication, and obtain

    1. Power down the air conditioner using the "power" button on the front
    panel.
    2. Unplug the air conditioner from the wall socket.
    3. Hold the front panel "power" button down and plug the air
    conditioner in. Continue to hold the power button down as the machine
    goes through a brief test sequence (fan & compressor each come on
    briefly, etc). There is a "beep" sound at the end of the test sequence,
    and the machine will be off. At this point, you can release the power
    button.
    4. Unplug the air conditioner.
    5. Plug the air conditioner back in.
    6. Congratulations! You should now be able to operate the air
    conditioner normally for another 720 hours, but only if you followed
    the instructions above EXACTLY.
    _____________________________________________________
    Was this solution helpful? Show your Appreciation by rating it.
    Thanks for using fixya support..You have a wonderful day

    Jun 05, 2008 | Haier hwr10xc6 Air Conditioner

    1 Answer

    My air conditioner showing on the display is E1


    The E1 Error Code The most common reason for an E1 error code to be displayed on your air conditioner's front panel is to remind you that the unit's air filter needs to be cleaned. Many models will automatically notify you of this via an E1 error code display after the unit has been operated for a predetermined number of hours. For example, many Sharp models will display an E1 code after 720 hours of use. Alternatively, you could have dirt or moisture in your front button controls, causing them to stick or not function properly. This can be a common problem with many models of Haier air conditioners, but the issue is not restricted to any one manufacturer. Your air conditioner could also have a defective thermistor, which is part of the thermostat.

    For Samsung, the room thermistor needs replacing. This is a device that senses the temperature in the room.


    How to Fix an Air Conditioner When It Gives You an E1 Code eHow

    Jan 24, 2016 | Heating & Cooling

    1 Answer

    Error code E1 and E4


    PDF]SERVICE Manual - Quietside

    https://www.quietside.com/archives/.../Service%20ACC1800C.pdf
    When error occurs in air conditioner, error code is displayed on indoor unit .... Display priority order at overlapping error : E1?E4?E5?P0?P0?P5?P6?t1? ...

    Midea air conditioner error codes

    airmaster.net/midea-air-conditioner-error-codes/
    Midea air conditioner error codes. Indoor unit error code explanation: R series: ... E1, Indoor / outdoor units communication protection. E2, Zero-crossing signal error ... E4, Outdoor unit temp. sensor or connector of temp. sensor is defective.

    [PDF]Download the Fault Error Code Booklet - Samsung


    Dec 05, 2015 | Heating & Cooling

    1 Answer

    I replaced circuit board in whirlpool combo microwave / oven, shows fault code F2, error code E1.


    Did you get the circuit board from a trustworthy place?
    It is a circuit board error. Did you install it correctly - right wires to right connections?
    Control displaying F2 E1:
    There may be a problem with the User Interface (Touchpad), or the associated wire connectors.
    Power unit down by turning off the circuit breaker(s) for one (1) minute.
    Power unit up by turning on the circuit breaker(s).
    Monitor the oven for one (1) minute to ensure the error code does not display again.
    Verify oven operation
    Have to go the long way to bring up the link by first:
    e1 f2 whirlpool oven Google Search
    and then click on https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwjprvf2_7nJAhXKVRoKHe7zAmMQFggdMAA&url=http%3A%2F%2Fwww.whirlpool.com%2Fproduct-help%2Ferror-code-oven-f2-error-code-f2-e1%2FPH7389%2F&usg=AFQjCNFoDK8E-zgNHF3Kp4EoihGu1tbyEw

    Dec 01, 2015 | Whirlpool Ovens

    1 Answer

    Comfort Control Center 2. Why is E-1 error displayed?


    [PDF]Customer assistance for air filters cleaning (E1 code)

    www.sharpusa.com/.../air_man_AFS100FX_S120FX_S125F...
    Sharp SolarCustomer assistance for air filters cleaning (E1 code) on Sharp Air Conditioners. The display will indicate an E1 code and not allow the unit to operate until the ...

    Sep 08, 2015 | Dometic Rooftop RV Air Conditioner

    3 Answers

    My unit shut off now displays E1.


    Sharp updated the procedure for resetting the E1 code.

    1. unplug unit
    2. hold the Power button while plugging the unit back in
    3. keep holding the Power button until the unit beeps
    4. unplug unit again
    5. plug it back in and it should be good

    Here is the updated user manual

    http://www.sharpusa.com/downloads/archives/product_manuals/air_man_AFS100FX_S120FX_S125FX_R100FX_R120FX.pdf

    Jun 05, 2010 | Sharp AF-S120FX Air Conditioner

    3 Answers

    E1 error code on air conditioner


    I called haier about this error code. E1 indicates that a button on the control panel or the reomote is stuck. I was instructed to unplug the unit and push each button at least 5 times, one at a time. Plug the unit back in, and this fixed my problem with error E1 and the unit works fine.

    Jun 23, 2008 | Haier HWS08XC1 8,000 BTU Window Air...

    3 Answers

    Error code on air conditioner e1


    Search for this problem on web or contact Sharp Technical Support for the following procedure:

    1. Unplug unit.
    2. Hold down power button while plugging in unit. It will do a short self-test and then beep. leaving unit off.
    3. Release power button and unplug.
    4. Plug in again and turn on normally. This should last for about 720 hours, at which point the E1 error will come back and you need to follow the procedure again. (You might as well clean the air filter at this point just in case it really needed it...)

    Jun 09, 2008 | Heating & Cooling

    1 Answer

    Error code


    Do you still the warranty for this unit? maybe you should contact the company which you bought the unit.

    May 31, 2008 | Haier hwr10xc6 Air Conditioner

    Not finding what you are looking for?
    Haier hwr10xc6 Air Conditioner Logo

    16,941 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Haier Heating & Cooling Experts

    Tom Chichester

    Level 3 Expert

    27817 Answers

    Caleb Brunson
    Caleb Brunson

    Level 2 Expert

    54 Answers

    Taylor

    Level 2 Expert

    202 Answers

    Are you a Haier Heating and Cooling Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...