Question about Frigidaire ATF6000ES Front Load Washer

1 Answer

E-43 still after a new control board

It will start fill with water and then only count down to 27 on a 31 min wash cycle then it just turns off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 868 Answers

Try holding the start/pause and cancel key together for 3 seconds. The door lock, wash, rinse and final spin lights should light. Any error codes should be displayed when holding those keys.

Posted on Jun 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bosch washing machine starts filling with water, then does nothing, timer counts down but no movment


have a technician check it out as it may be a board problem
normally the fill level switch ,when the set water level is reached activates 2 things
it stops the water in and at the same time moves the program on to start the wash cycle
so it is either that switch or the program board

Aug 13, 2015 | Bosch Washing Machines

1 Answer

My maytag washer when i start it it fills then the cycle starts the timer will count down til it get to 13 min then jumps down to 3 min then shuts off it skips the wash cycle and the rinse cycle befor


sounds like you have a problem with the main control board. you can order a new one from appliancerepair.com and if it turns out not to be the problem they allow you to return it for a full refund. great company!

May 26, 2014 | LG Washing Machines

1 Answer

Start wash program, fills with water, then drum does not turn.. Tried rinse progam, water ,does not turn.. Can hear relays clicking but nothin moving. But the time carries on counting down. It does drain...


If the motor is not spinning, you may have a burnt out motor or faulty Motor Control Board. Else, if the motor is spinning, fix the belt from the motor to the drum.

Oct 29, 2011 | Bosch Exxcel WFX 3267 Front Load Washer

1 Answer

F&P washing machine:GW709 doesn't cut out when filling


could b pressure switch tube is blocked or your control board with the pressure switch attached is faulty. empty water from machine, remove pressure switch hose from control board, blow thru tube to remove any blockages, refit tube. turn on cycle, select low water level, push start, after about 30sec"s push start again, that should stop it filling straight away. if the water stops push start again to continue filling. if it doesnt stop filling after restarting the cycle then it is your control module.if the water doesnt stop filling after the 30 sec stop it is the water valves. by the way what country do u live in because $120 seems to b alittle too expensive. please reply 4 more help.

Apr 29, 2010 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

I have a front loading GE wcvh6260fww that will fill with water, but will not agitate or spin out the water...thus, no washing of clothes regardless of cycle selected. The timer counts down and the water...


probably a bad door switch, if you can take the door or top off and find the wires running to the switch take the wires off theswitch and plug them together by wrapping electrical tape around them and then try the washer. If that dont work may be a bad control board

Sep 03, 2009 | GE WCVH6260FWW

1 Answer

Wash cycle and spin


you need to check a simple button called " no spin" may you will see it marked "aspiral shap" and has "x" over
good work !

Jul 05, 2009 | Zanussi ZWF1430W Front Load Washer

1 Answer

My maytag neptune washer stop washing with 10 minutes left to go.


If your machine is a FAV6800AWW or FAV9800AWW the (upside down u and f) may be a “NF” for no fill error. The washer has tried to fill the machine with water and has sensed a water fill issue. The control board has shut the wash cycle down with an “NF” error to the display because of excess time to complete the water fill portion of the wash cycle.
Will the machine complete the cycle with Hot water only or Cold water only? I would do a Quick Wash cycle just to test with an empty wash basket.
Regardless of the above test and assuming you have good water pressure for both Hot and Cold supplies to the washer I would do the following. Close the water source valves to the washer and remove the Hot and Cold hose connections at the back of the machine and check for clogged inlet screens. If the water inlet screens are free of restrictions I would go into Service Mode and turn on the Hot and Cold water valves on one at a time and make sure the tub will fill with about 2 inches of water in about 3 minutes in service mode. Check both Hot and Cold inlet valves individually see page 16 of the SM Board Output Test, enter service mode and do the function test for both Hot and Cold Water Valve’s. If the inlet screens are clean and you have water fill restrictions in service mode we may need to look at replacing the water inlet valve assembly. You can turn on the drain pump in service mode to empty the tub or just start a wash cycle and the machine will empty the tub.
The Service Manual for reference. Sears Parts Direct for reference.


May 11, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Washer fills with water and thats it


Possible a bad motor control board. Depending on the age of the washer, you may need to replace the motor control board and the motor as a kit. Also be sure to test that the motor control board is getting power, I've seen cases of the motor/ motor control failing and taking out the main control also. The tech sheet is in the console and should walk you through the steps.

Jul 18, 2008 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Washer agitates for a time then sputters. Does not spin


In sounds to me like you have a motor issue. We have found that on these particuliar models, that the motor tries to run in both speeds at the same time. If you already replaced the control board, then you will have to get a new motor kit. This kit includes directions as well as a new wiring harness and start capacitor. You would have to remove the old motor and rewire the wiring harness (instructions included with the kit) and add the new start capacitor (instructions also included). Job is'nt really that hard to do. Front cover would be all you would need to remove to get to all the parts. Good luck and let me know how it turns out or if you need any additional help. Jim

Sep 05, 2007 | Washing Machines

Not finding what you are looking for?
Frigidaire ATF6000ES Front Load Washer Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...