Question about Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

1 Answer

Kenmore 16359 dishwasher

I have a kenmore dishwasher 16359 model 665.160119401 the normal wash light is blinking. tried unplugging still blinks. can you assist

Posted by on

  • ca12 Jun 04, 2008

    the machine was working fine. we went on vacation and when we got back the light was blinking. just thing to figure out what happened and how to fix it..

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 413 Answers

The blinking buttons indicate the buttons are bad. The console will have to be replaced.

Posted on Jun 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can I do my dishwasher Kenmore model 665-13834K601 the Cancel and Normal wash lights are blinking and won't work


Try this, unplug it from wall outlet for one minuet to reset its processor. Then plug it back in to see if that worked.

Dec 03, 2014 | Kenmore Dishwashers

1 Answer

Kenmore elite quiet guard deluxe


The model number is normally on the side of the door or frame. Otherwise if you unplug your dish washer I would suggest taking the front face off the door and see if you can find a service manual. Those blinks may be an error code

Jul 31, 2013 | Dishwashers

1 Answer

Normal wash light blinking, d/w wont start


Wish I could solve this, as I'm having the same problem too. Normal light blinks not matter which wash button is pressed. Cancel light will light, but still NOTHING happens. Same model as yours.

Jul 23, 2010 | Kenmore PRO 24 in BuiltIn Dishwasher with...

1 Answer

The clean light is blinking and the dishwasher does not run???


Close the dishwasher door. Push the "normal wash" button, then push the "heated dry" button. Push the "normal wash" button again, and push the "heated dry" button again.Try out his and see what happens.It must reset the memory and your dishwasher must work.

Jul 06, 2010 | Kenmore 24 in. 16352 / 16354 / 16359...

1 Answer

The Normal Wash light blinks constantly. I cannot


Try unplugging it for 15 then plug it back in. It should reset itself. Sometimes water temp sensors or water level sensors can get dirty or corroded and give you this error.

Jun 14, 2010 | Kenmore 24 in. 17012 Built-in Dishwasher

1 Answer

Kenmore Ultra Wash Dishwasher LIghts are blinking....


I suspect for either of these units that the timer control boards are bad.

Jan 24, 2009 | Dishwashers

2 Answers

Clean light keeps blinking and I can't start a new cycle


That is a comon problem with that model. It is not sensing a temperature change in the water.

Push i believe it is heated dry and sani rinse going back and fourth between the two to clear the code and see if you can get it to complete a cycle. If it doesnt call sears and schedule service there is a service flash repair that should not cost you anything to repair the unit.

Nov 13, 2008 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Kenmore elite model 16574


press (high temp-wash) button and then ( heated dry)
do that 3 times in that order within 5 seconds. So it looks like this:

(high temp-wash) ( heated dry) (high temp-wash) ( heated dry) (high temp-wash) ( heated dry)

That will start a short diagnostic cycle (last about 2 minutes) that will clear the blinking light and allow you to use the dishwasher. If the light comes back, your drying cycle has failed and you will need service.

Oct 28, 2008 | Kenmore 24 in. 16352 / 16354 / 16359...

2 Answers

Kenmore Ultra Wash Dishwasher LIghts are blinking....


I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Feb 11, 2008 | Kenmore 24 in. 17262 Built-in Dishwasher

3 Answers

MAYTAG DISHWASHER STUCK WITH LIGHT BLINKING


Try holding down "Heated Dry" for about five seconds, until the light switches off. You should be good to go.

Oct 20, 2007 | Kenmore 15129 Built-in Dishwasher

Not finding what you are looking for?
Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...