Question about Gaggia Coffe Deluxe Coffee Maker, Espresso Machine

1 Answer

No heat I have the same problem. Did you get anywhere with it? Ben A

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 515 Answers

Hi,

Take off the top and you will see the boiler, you will see thermostat on the boiler, there will be a pin on one reset it by press it down.

Posted on Jul 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Krups xn7106 leaking from base


You are going to need to remove the covers and run it up to observe where the water is leaking from. Any leak at all inside the housing from anywhere is going to come out the bottom. There are teflon tubes and O rings inside that shrink with time and heat. More likely to be leaking closer to the boiler where water is hottest. Just be careful running it up with covers off, remember electricity can kill you so look with your eyes not your fingers.

Dec 28, 2014 | Krups Coffee Makers & Espresso Machines

1 Answer

My Keurig will not come on


I am afraid you should check prices. sounds like it wore out.

Sep 24, 2014 | Keurig B60 Coffee Maker

1 Answer

I think I need a new heating element for a Capresso 452. Are these available anywhere?


Coffee Maker manufacturers rarely sell individual parts for the machine aside from filters and whatnot. I recommend replacing it.

May 11, 2011 | Jura Capresso 452.01 Coffee Maker

1 Answer

Heb geen handleiding meer en display werkt niet.


beste heren

ik ben in het bezit van een saeco royal exlusiv
nu geeft hij aan groep geblokkeerd zetgroep zit er goed in maar draait niet welke toetsen code moet ik in drukken om te restten
b.v.d hans

Oct 17, 2010 | Saeco Incanto Classic Espresso Machine

2 Answers

We havn't had our Delonghi BCO-120T but for 3 months & the coffee side stopped working all together. My husband is a great handyman & after taking that side apart. the tubing & tank looks...


In uk delonghi spares by agents of kenwood.co.uk. there is a directory of local agents. before ordering element check thermal fuse attached to the element it may be open circuit.

Jul 29, 2010 | DeLonghi BCO120T Programmable Espresso /...

2 Answers

DOES THE BLACK N DECKER SPACEMAKER COFFEE POT HAVE A FUSE IN IT ANYWHERE,


It should have a thermal fuse (looks like a 22 shell with a wire from each end) that is supposed to melt it's internal link when the near-by temperature is too high. A replacement is to be 'crimp connected' as soldering the connection will kill the fuse again. It is located near the heating element. A defective thermostat will often cause the overheating that pops this fuse.

Oct 31, 2009 | Coffee Makers & Espresso Machines

2 Answers

I think our heating element is bad on our Ascaso...we checked it with an ohm meter. When we turn it on, the water doesn't heat up, and there's no steam. Is there anywhere we can get a new element for...


Sounds very much like the element has gone. Mine went after I moved house (suspect something happened during transit). Mine was replaced by a heating technician who wasn't even an official Ascaso agent, so I guess the answer I would give would be go to a local heating systems technician/company. Mine cost a bit more than that, but I got them to change it, so if you're doing it yourself you might get it for under $100.

Oct 21, 2009 | Ascaso Dream Espresso Machine

2 Answers

We have a Faberware super fast fully automatic coffee maker model fcp 280 and it doesn't heat up anymore can I repair it? Ben


If the power cord can be removed via a plug on the unit you should test the power cord for continuity. This can be done with an inexpensive multimeter. The cord should be removed from the coffe maker and the wall outlet. Then connect one of the probes on the meter to one of the prongs that go into the wall. The other probe of the meter should be touched into one of the two holes in the other end of the plug. You should set your meter to read resistance or ohms. If the meter reads close to zero then one leg of the cable is fine. If it blinks a "1" that usally indicates an open connection on a digital multimeter. If that is the case then connect the probe to the other prong. Once this is done then you need to test the other prong.

Hope this make sense.

If you get continuity on both legs of the power cord then I can explain further how to test the coil in the coffee pot itself.

Bob Janelli

Oct 01, 2009 | Faberware FCP280 Coffee Maker

Not finding what you are looking for?
Gaggia Coffe Deluxe Coffee Maker, Espresso Machine Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gaggia Coffee Makers & Espresso Machines Experts

Ernest R
Ernest R

Level 3 Expert

1618 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Gaggia Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...