Question about Compaq Netelligent 3612 (267007-001) Networking Hub

2 Answers

Wireless card hi. my nec i-select m5210 laptop has a Ralink RT2500 Wireless LAN Card installed but i cant seem to get a wireless connection. is there a switch i need press to activate this if so where is it located.i can get wireless network when usin netgear wireless adapter but not without.i cant seem to find a users manual anywhere. can u please help me get my laptop on wireless.

Posted by on

  • Trudy Foreman Jun 11, 2008

    hi.thanku firstly i have tried all sites & cant find any form manual to download.also i have tried uninstallin & reinstallin drivers to no avail.i have also updated driver but still no help.any other ideas pls

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 118 Answers

If you have drivers installed properly and your wireless card is in the "on" condition and still it dont get any signal from wireless router/switch.

Try restarting the "Wireless Zero Configuration Service". here is the path to follow.

1. Go to Control panel. 2 >>> Administrative Tools 3>>>>> Service

>>>>> Find "Wireless Zero Configuration Service" and restart it....

Let me know if it helps...

Regards,


Posted on Dec 02, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 25 Answers

Some do have switch where it is is always specific to each manufacture, so go to the manufacture web search for your model, and download the pdf version of your laptop model,
]
secondly check the device panel to make sure the driver is installed, if not install it, if it is already install, uninstall it and reinstall it, sometimes these small mechanical humans lost their mind and need somebody to give them a fresh start so do that.

let me know if this helps

Posted on Jun 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a D-link DGS-1005G. I have two computers connected and a printer. The D-Link is also connected via LAN. I can obtain internet connection to each computer with wireless and the printer will not...


Hi, you have to set up your printer as a device that can be communicated in your LAN by the two PCs.

To set up your printer properly in the LAN, you need to assign a fixed IP to this printer such that whenever it is switch on again, both PC still communicate to this printer without changing the new IP assigned to this printer.

You need to set up this fixed IP properly in your DLink router. For guidance please check this in your user manual of the Dlink. Please let me know any problem you may have again in future.

Aug 10, 2011 | D-Link DGS 1005D (DGS-1005D) 5x1000 Mbps...

1 Answer

The power light for the router keeps on flicking and cant even log in. have done all the necessary things. any other help?


Try resetting the Linksys back to the default settings - Press and hold the pinhole RESET button at the back of therouter with the power ON for 20 secs. then release the RESET button.
To connect to your wireless router, the router's wireless settings needs to beconfigured with the SSID, encryption etc. and also the wireless cards in allthe laptops/computers needs to be configured with these router's wirelesssettings. Then the laptops/desktop computers can communicate with your wirelessrouter.
Connect a LAN cable from the Linksys to the LAN port on your computer.
Open a browser and enter the Linksys configuration URL
http://192.168.1.1
The default login = admin
The default PW = admin
You can protect your router by changing the default PW (write it down and putit in a safe place)
Go to the wireless configuration and set up the SSID and WPA or WPA2encryption.
Apply these settings to the wireless card in your laptop/computer.

To secure your wireless network from unauthorized access, please click on thislink and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Apr 27, 2011 | Linksys BEFW11S4 802.11b Wireless...

2 Answers

How do i find out my WPA (WEP) key? I bought a G wireless router several months ago but can't get my laptop to work with it.


To connect to your wireless router, it needs the router’s wireless settings configured and also needs the wireless cards in all the laptops and or computers to be configured with the router’s wireless settings. Then the laptops and desktop computers can communicate with your wireless router.

To set-up and secure the wireless router from unauthorized access, follow these steps: -
1. Connect the wireless router to your computer with a LAN cable.
2. Start your browser and enter the router's configuration URL IP address.
3. Enter the router setup, login and password
4. Change the admin password
5. Go to the wireless settings and change the default SSID and turn off SSID broadcast.
6. Setup encryption key the strongest is WPA2 (if not then WPA).
7. For further security measures - turn on MAC address filtering and enter the MAC address of the wireless cards on the computer/s you want to connect to this wireless router.
8. Record the settings you have made and keep it in a safe place and Save the settings.
9. Configure the wireless cards on the computer/s with the SSID and encryption settings of the router.
10. Remove the LAN cable between the router and the computer then the computers should be able to connect to the router wirelessly.


If you cannot get into the Belkin's wireless configuration you can reset the router back to the default settings by pressing the RESET button at the back of the router for 7 secs. The setup IP address is 192.168.2.1 and the default password is blank.

Nov 29, 2009 | Belkin Computers & Internet

1 Answer

Cannot connect to internet via wireless hub to laptop


When you power up the wireless router and the LEDs are ON then the router appears to be OK and this also applies to the DSL or cable modem.
To check if the modem is configured to your ISP settings and connects to the Internet, connect the modem with a LAN cable to your laptop and check if you can connect to the Internet.
Next, the wireless router needs the wireless settings configured and then configure the wireless card in the laptop with these settings so it can communicate with the wireless router.
To set-up and secure the wireless router from unauthorized access, follow these steps: -
1. Connect the wireless router to your computer with a LAN cable.
2. Start your browser and enter the router's configuration URL IP address.
3. Enter the router setup, login and password
4. Change the admin password
5. Go to the wireless settings and change the default SSID and turn off SSID broadcast.
6. Setup encryption key the strongest is WPA2 (if not then WPA).
7. For further security measures - turn on MAC address filtering and enter the MAC address of the wireless cards on the computer/s you want to connect to this wireless router.
8. Record the settings you have made and keep it in a safe place and Save the settings.
9. Configure the wireless cards on the computer/s with the SSID and encryption settings of the router.
10. Remove the LAN cable between the router and the computer then the computers should be able to connect to the router wirelessly.

Nov 14, 2009 | Computers & Internet

1 Answer

How a conect to internet


METHOD 1 - Using Internet connection using DSL or cable connection.
1st. If you wish to connect to the Internet with a LAN cable or a wirelessly and if your computer doesn't have a LAN card or wireless LAN card you need to purchase a LAN card (to configure the wireless router) and if you want a wireless connection you will also need to purchase a wireless LAN card.
2nd. You need to select an Internet Service Provider in your area with a plan and cost to suit your requirements.
3rd. You need to decide what type of broadband connection you need, DSL or cable modem with or without a built-in wireless router, the Internet Service Provider can assist you with this.
5th. The Internet Service Provider can supply these items or advise you what make and model to purchase. They will also provide information on how to connect and setup your Internet connection.

METHOD 2 - Using USB wireless adapter that plugs into the laptop's USB port. It doesn't need a wireless router or a cable or DSL modem.
This is used mostly on laptop computers which allows Internet access anywhere the Internet Service Provide has a wireless transmitter. It uses the G3 mobile system.
This type of service usually costs more and again you need to select an Internet Service Provider that can provide the wireless coverage, the plan and costs that suit your requirements.
Installation and setting up information is supplied by the ISP.


Jul 31, 2009 | Computers & Internet

2 Answers

I can not get my laptop and my ps2 to connect to internet at the same time


hi Lorraine! may i know what type of laptop brand do you have? mac or etc..?

Sep 30, 2008 | D-Link DES 1005D (DES-1005D) 5x10/100 Mbps...

1 Answer

Shared internet connection help!!!


are you using window xp for both pc?

Aug 25, 2008 | Computers & Internet

1 Answer

Wireless connection


Dear Sir/Madam,

I suggest you remove you net work and start again connect pc's and connect to internet at the same time
your sub net address is proberly wrong
255.255.255.0 is correct
255.255.000.0 means no internet

Thanks
Good Luck

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} "Don't forget to rate the solution"

Jun 30, 2008 | Computers & Internet

1 Answer

Laptops satellite pro


Hi,

I think in your Pc Wireless lancard is disable,Pls enable the wireless lancard, I can suggest the configuration,
Go to my network place-----properties----wireless card---enable

Jun 07, 2008 | Toshiba Computers & Internet

1 Answer

Wap versus wep encryption


your wireles card is not able to use WPA only WEP

Nov 22, 2007 | 3Com 3C16985B /REF3COM SSII 24-PORT SWITCH...

Not finding what you are looking for?
Compaq Netelligent 3612 (267007-001) Networking Hub Logo

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Compaq Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18330 Answers

Are you a Compaq Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...