Question about Technics SA-DX1040 Receiver

1 Answer

Fan quit working. Is it likely the board, or the fan? Currently have a Radio Shack fan mounted; it's 120v, plugged into the AUX power on the back of the unit. It's noisy, otherwise unit works and runs cool - however, now it overloads on modest volume with music. Is this unit worth fixing? Thanks!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi, Have got and still use a Technics SA-GX910 Dolby Amp. It had an overheating problem too due to Air temp and power drain etc and the internal fan only engaged at certain volume level. Overheating was overcome by adding another internal fan.
Your unit however might need a bit more of a fix-me-up or throw it away

Posted on Oct 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lights up but when pressing Quick Start it automatically shows the lady liberty,etc for a moment then goes back to the Bowflex logo and nothing else. Help!


I was having the same issue to a T. I called Bowflex tech support, they told me that without a doubt the main pc board that is under the treads needed to be replaced for $515. I then trouble shot myself and got it up and running in minutes for $0. Take of the plastic top from the pc board area, unplug the little clipped in 2 wire plug labelled Fan. It litterally says fan on the board and you can see 2 wires going right to the fan. Once that is disconnected try to Quick Start. It should work. You can either replace the little fan for $6 @ radio shack or run a fan your self simply by facing your own in the same area. Most people are running a fan for themselves anyway, just aim for both. Good luck.

Mar 06, 2014 | Bowflex TreadClimber TC5500

1 Answer

C7 error code


C7 code has to do with your main fan. Either its not working due to it being blocked or having gotten wet/damaged/power surged, or your control unit isn't supplying the correct 120V to the fan. Your control has a ceramic fuse that you can test as well.
First, look for 120V to either the left or right pair of wires in the molex plug on the fan. if you have voltage, then the fan is bad. If you dont, its either just a fuse, the board is bad, or the fan is bad causing the fuse to blow. Insert the supplied spare fuse, and power up the unit. If it blows the fuse again, its the fan.

Mar 03, 2014 | Bosch AquaStar Indoor Natural Gas Tankless...

1 Answer

Ge jkp15aa


Take the back off the control panel and see if you can access the board. If you can see the board component side, go to radio shack and fgget freeze spray. Start the oven and when it quits like you described, spray one part on the board at a time till it comes back on. OR buy a new board

Feb 07, 2013 | GE JKP15 Electric Single Oven

1 Answer

Inside blower wont run


Sounds like you need a new board. Their are people out there that will replace the fan relay on these boards, but I have always just replaced the whole board with a new one. These boards can range from around $50 to $300 depending on which board it is. The way we always double check these boards are exactly the same way you have done it, only we use the 120v from the units transformer and bypass the board, if your fan comes on, your board is not sending the power through to the terminals. It would be different if nothing else on your system was working too. I hope this helps and good luck!

Jul 01, 2012 | Ruud Rheem Honeywell Fan Control Board...

1 Answer

MY carrier model #58DHC with hot surface ignitor has quit working. Blower works, but no heat. If you turn the thermostat to on fan will run but no heat. Did preliminary testings with self test on printed...


If you suspect its the ignitor? The hot surface ignitor is powered by 120v. Inspect ignitors' hot surface for cracks or burnt spots. Uplug ignitor from board. Cycle heat on and verify 120v to the ignitor at the cannon plug on the board where the ignitor plugs in. If you have the voltage then replace the ignitor. If not, you'll need to verify all other circuits are working before condemning the board. Work safe and at your own risk! Hope this helps!

Mar 25, 2017 | Heating & Cooling

1 Answer

Evaporator fan motor no working.


First off you need to check to make sure you are getting 120v to the evap fan motor. If this is an amana or maytag ref then it could be caused by a bad defrost termination killing power to the evap fan motor. If you have 120v to the evap fan motor then it will need to be replaced. Sometimes if you remove the back panel you can start the fan motor back up by giving it a nudge with a screwdriver.

Hope this helps _MJ_

Feb 07, 2010 | LG Refrigerators

2 Answers

Need a replacement capacitor


Voltage rating doesn't matter. 250v or 330v will work.

If this is really a 2 speed original, with the 2.5Amp motor... it will NOT have a capacitor as the motor is a shaded pole unit. The three speed electrically reversible fans, have a capacitor, which can either be in the switch housing/ oil reservoir, or the top of the motor housing, depending on year of manufacture.

Oct 24, 2009 | Hunter 23852 Classic Original Ceiling Fan

1 Answer

Connecting electronic air filter to furnace fan


You may need a "current sensing relay" to clip around the neutral wire on your blower.
Run the 120v power to the main power (the power switch- hot,neutral and ground) . Run the Hot wire through the "Current Sesing Relay" wires to the EAC unit's 120v. power input. The unit will only run when the fan is on.

Hope this helps,
Matt

Dec 31, 2008 | Goodman Heating & Cooling

1 Answer

New fan not working but lights work


There is less than 120v getting to the fan. Its possible that the lights will turn on etc. Take an extension cord and plug it in another plug and grab both power wires from the fan and stick them in other end of extension and I do service calls for broan & Nutone

Jean-Marc
try it out. Im sure your not getting 120v completelty.

Feb 05, 2008 | Broan-NuTone Allure QS130SS Kitchen Hood

3 Answers

Panasonic SA-HT680 DVD Home Theater Sound System


when i turn my home theater system on it says f61 then it shuts off can u plz help me out here =[

Apr 18, 2007 | Panasonic SC-HT680 System

Not finding what you are looking for?
Technics SA-DX1040 Receiver Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5011 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Technics Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...