Question about Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

1 Answer

Dishwasher won't start

The light comes on when the cycle button is pushed but the dishwasher start button and delay button will not work

Posted by on

  • BR335 Jul 19, 2008

    I have a model 665 15805891. select any cycle and red light comes on over cycle selected, push start and the light goes out and nothing happens. push start again and the motor starts. there is no water in the washer so you have to hit cancel drain on key pad to stop motor.

    I replaced the electronic board and it appeared to be ok. Filled with water and started the wash cycle, I had to run an errand so I stoped it thinking I had fixed the problem. The next day filled with dishes and detergent I had the same old problem I described at the beginning. They let me return the board so I put the old one back in and it's back to square one. Please help.

  • Anonymous Mar 14, 2014

    Trying to start dishwasher but delay button keeps coming on, how do we start it without this happening

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 110 Answers

THIS IS A ISSUE WITH A THERMAL FUSE WHICH IS ATTACHED TO THE MAIN PROCESSING BOARD GO TO WWW.SEARPARTS.COM FOR THE PART BREAKDOWN AND ILLUSTRATED MODEL

Posted on May 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am getting a 5H in the panel where the time cycle usually is and when I hit start it won t start


I think your dishwasher is in delay start mode. Some dishwashers can be set to start at a later time say for instance while everyone is sleeping. See if your control panel has a button that says delay start. If YES--just keep pressing it until it clears. Some go as high as 12H which is a 12 hr delay.

Feb 28, 2015 | GE Dishwashers

1 Answer

Purple light is on and cycle won't start


It's possible that you have put the dishwasher into delay mode. Try powering off at the powerpoint as this will force a reset of all programming.



The pause/start button also sets the Delay Start feature which can delay the start of a wash program
from 1 to 12 hours.


To cancel Delay Start
Press the I button.

Dec 30, 2012 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Wash cycle does not start. I push the normal wash (or any other cycle) button and a tiny amount of water flows. If I leave it alone, eventually, several lights start flashing. I have tried pressing the...


Hi,
Either the hose is clogged at the entry point to the dishwasher or the solenoid vlave is bad...

Here is a tip that will help you to find out why water will not come into the dishwasher...

Dishwasher Trouble
No Water entering Dishwasher

heatman101

Dec 21, 2010 | Dishwashers

2 Answers

My frigidaire dishwasher model #fghd2433kf1


It is in a delay wash mode.
Disconnect power for 60 seconds.
Re-connect power.
Press the Cancel button.
Press the regular wash cycle and start the dw.

Jul 17, 2010 | Frigidaire Dishwashers

1 Answer

Flashing lights on Maytag dishwasher


Check whether the door is getting closed fully. Try pushing little hard. If the door close switch problem it may work.

Contact service for help if u can not proceed further with electrical circuits. Micro-controller board to be checked!

May 18, 2010 | Dishwashers

1 Answer

Electrolux dishwasher delays before starting


  1. To cancel the delay.press the delay pad again when the delay is counting down. The indicator light will go out and the cycle will start or resume immediately.
  2. To cancel the delay and the cycle, press Start/cancel once to drain and turn-off the dishwasher.
  3. Press Start/cancel twice to turn-off the dishwasher without draining.

Aug 31, 2009 | Electrolux EDW5505ESS Built-in Dishwasher

1 Answer

Control panel lights but won't start


the front control panel fries out.. We had to have ours replaced after 7 months ... after that was replaced it only lasted 2 months... WE ARE VERY disappointed and will be calling once again tomorrow. The dishwasher is not even a year old yet!

Aug 16, 2009 | Maytag MDC4650AW Built-in Dishwasher

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to...


SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Aug 01, 2009 | Bosch SHU5315UC Dishwasher

Not finding what you are looking for?
Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...