Question about Kodak EASYSHARE 5300 All-In-One InkJet Printer

1 Answer

Won't scan MY EASY SHARE 5300 WILL NOT SCAN OR COPY. WHEN I TRY TO CALCIBRATE THE PRINTER IY SAYS IT'S NOT READING THE CALIBRATION SHEET. AND WHEN I TRY TO COPY, IT PRINTS OUT A SOLID SHEET OF BLACK

Posted by on

  • Anonymous Mar 23, 2014

    All I get is a black sheet when trying to copy or scan. Printer still prints OK

  • Anonymous Mar 23, 2014

    Printer prints OK but can't scan or copy. All I get is a completly black sheet on the sheet

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

Upgrading the firmware could solve the problem if not calling tech support for further troubleshooting would be best..

Posted on Jun 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kodak easy share 5300 has printing issues. I


Try this one, Turn on the printer, Take out the inks, remove the printhead, put back the printhead make sure it will snap and you hear a click, put the inks back, wait for the printer to initialize, Press the Menu button, look for Calibrate printer, then print calibration page, then scan it after. Load a regular paper. Then try to print a demo page by pressing Photo and Copy at the same for 5 seconds then let it go. If same problem persist call this no for further assistance 1800 421 6699
Thanks

Aug 29, 2009 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

Kadak Easy Share 5300 printer. Screen reads "Paper Jam Clear Jam


Try this one Take out the inks and printhead Leave the cartridge door open, then unplug the power cord from the back of the printer while the access door is open Close the cartridge door once the cord is unplugged Reconnect the powercord, turn on the printer, then your printer will look for your printhead "Printhead missing or not installed correctly..." Then put everything back. make sure it will snap in to place. Then print a calibration page, then scan it. This is just over writing the error message. Thanks Josh - Kodak Tech Support

Aug 12, 2009 | Kodak EASYSHARE 5300 All-In-One InkJet...

2 Answers

My kodak easy share 5300 all in one printer will not scan


are getting any error msg like 1-2036 or anyother and are you using Vista or Xp,,,,try using the windows fax and scan settings....let me know and i will try and help you

Apr 04, 2009 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

My KODAK 5300 AiO printer wont print from PC


try pressing the copy and cancel buttons at once a blank sheet of paper will come out and that should solve your problem. I hope this helps

Jan 19, 2009 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

Printer easy share 5300


Remove the black and color ink cartridges.
Right above where the black ink cartridge was, in the top left hand corner of the printhead, push up towards the ceiling and you should be able to push a button that releases the printhead.
Place the printhead right back into the printer and push straight back on the back wall.
You should hear a loud snap.
Replace the ink cartridges which should snap as well.
Close the printer.
After about a minute or so the printer will ask you to do a calibration.
Insert a paper and press start.
Scan the calibration sheet.
After that, in the menu, do a printhead clean.
Do one basic and one deep.
Print a demo sheet to see if anything has changed.
If the picture looks better, continue to do cleans.
In the event that it does not, the printhead will need to be replaced and since the printer is still under warranty, Kodak specialists will try to overnight you a printhead.
The whole process is short and free.
The number for Kodak AiO Support is 1 800 421 6699.

Aug 01, 2008 | Kodak EASYSHARE 5500 All-In-One InkJet...

1 Answer

The black ink cartridge on my kodak easy share 5300 appears to be faulty. I have changed the cartridge and deep cleaned the print head as wel, any suggestions?


Depending on the issue, the solution may be just to replace the ink cartridge. If that does not work, try these steps:

Remove the black and color ink cartridges.
Right above where the black ink cartridge was, in the top left hand corner of the printhead, push up towards the ceiling and you should be able to push a button that releases the printhead.
Place the printhead right back into the printer and push straight back on the back wall.
You should hear a loud snap.
Replace the ink cartridges which should snap as well.
Close the printer.
After about a minute or so the printer will ask you to do a calibration.
Insert a paper and press start.
Scan the calibration sheet.
After that, in the menu, do a printhead clean.
Do one basic and one deep.
Print a demo sheet to see if anything has changed.
If the picture looks better, continue to do cleans.
In the event that it does not, the printhead will need to be replaced and since the printer is still under warranty, Kodak specialists will try to overnight you a printhead.
The whole process is short and free.
The number for Kodak AiO Support is 1 800 421 6699.

Jul 19, 2008 | Printers & Copiers

1 Answer

Owners manual for kodak 5300 printer


Hi - You can download the manual from the link below:

Kodak 5300

Please update the question & let us know if the information given was useful to you - Good Luck!

Jul 08, 2008 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

5300 Won't print text!


K...Trust the solution. Try these steps. Open the printer, remove the ink and remove the printhead (See User's guide). Reseat the printhead and the ink cartridges. The printer will come up with an error message that requires calibration. Do the calibration and scan the sheet that prints right after by pushing the start button. In the menu options, clean the printhead. Do one basic and one deep. Print a demo sheet (another menu option) to see if the quality has gotten better. If it has not call Kodak AiO Tech support. You will need a replacement printhead.

May 22, 2008 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

Printer


K...Trust the solution. Try these steps. Open the printer, remove the ink and remove the printhead (See User's guide). Reseat the printhead and the ink cartridges. The printer will come up with an error message that requires calibration. Do the calibration and scan the sheet that prints right after by pushing the start button. In the menu options, clean the printhead. Do one basic and one deep. Print a demo sheet (another menu option) to see if the quality has gotten better. If it has not call Kodak AiO Tech support. You will need a replacement printhead.

Apr 26, 2008 | Kodak EASYSHARE 5300 All-In-One InkJet...

Not finding what you are looking for?
Kodak EASYSHARE 5300 All-In-One InkJet Printer Logo

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Printers & Copiers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Michel Smith

Level 3 Expert

1218 Answers

Sajid Najmi
Sajid Najmi

Level 1 Expert

31 Answers

Are you a Kodak Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...