Question about AT&T TL7600 Wireless Headset

3 Answers

How do I put the TL7600 att headset into pairing mode?

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Here is the solution to deregister the TL7600 without the base:


Push these buttons in the following order:

  • vol+
  • mute
  • vol-
  • mute
  • vol+
  • vol-
  • mute

Posted on Oct 18, 2013

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 4 Answers
  • Rohit
    Rohit Dec 31, 2015

    *** How to Pair AT&T TL7600 with AT&T 86103 or 86109 !!!



    If you have been going nuts on how to pair TL7600 with TL86103 or TL86109 Deskphone, here is a detailed answer.





    http://i.fixya.net/uploads/images/pair-t...">



    http://i.fixya.net/uploads/images/pair-t...">

    http://i.fixya.net/uploads/images/pair-t...">

    First of all TL7600 does not need pairing, it is a passive wireless i.e it remains in hunt mode till a deskphone actually pairs with it.



    First things first - Charge the Dect Headset TL7600 for 1-2 hours. Press the On/Off button once and you will see a blue/red light that will keep blinking every 2-3 seconds. This shows that the headset is unregistered with the Deskphone. When the headset becomes properly paired and placed on the charger, it will show steady blue light.



    Okie, now to registering the headset.



    a) First, lets reset the TL7600 just incase it was paired to another phone. Even if it is not, lets just do a reset to avoid some problem.



    Push these buttons in the following order one by one :



    Push these buttons in the following order:

    vol+mutevol-mutevol+vol-mute

    b) Go to the TL86103 and keep TL7600 very close to it. Lift off the TL7600 off the charger and then put it back in.







    c) Press "MENU" on telephone mode with phone handset on the phone and the phone in Idle Mode.



    c) Scroll to "Settings" and then scroll to "Register"



    d) All this while, the TL7600 should be on the charger. If you remove it from the charger, it will not register.



    e) Within 90 seconds to 2 minutes, the headset will be registered and you will see the handset will be assigned a name on the phone.



    f) Pick up the headset, switch it on and you will hear a dial tone.



    g) If this doesnt work, try to first press hold for 10 seconds till it says "Unregister All Devices', Click Yes and go through the process again.



    j) If you want to know how to make a call, please note that the call will have to made first on the deskphone, then switch on the headset and there you go. Either lift the reciever and make a call or press Speaker and make a call and then switch on the headset, put the deskphone handset down or switch off the speaker and your TL7600 will be connected.



    *** For TL86106, everything is same till (b). After that, press HOLD Button on the phone for 4-5 seconds till you see "Registering". Within 90 seconds to 2 minutes, the device will register the TL7600.http://i.fixya.net/uploads/images/pair-t...">

×

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 23 Answers

Did a quick search on google and found the manual for this, read page 6.
http://smbtelephones.att.com/docMgt/public/art/595984/TL7600_manual_i6.pdf

Posted on Oct 08, 2010

  • mlmosner
    mlmosner Oct 18, 2013

    Here is the solution to deregister the TL7600 without the base:

  • mlmosner
    mlmosner Oct 18, 2013

    Push these buttons in the following order: vol+, mute, vol-, mute, vol+, vol-, mute

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to pair AT&T TL7600 with AT&T 86103 Deskphone


*** How to Pair AT&T TL7600 with AT&T 86103 or 86109 !!!

If you have been going nuts on how to pair TL7600 with TL86103 or TL86109 Deskphone, here is a detailed answer.


pair-t-tl7600-t-86103-deskphone-wg3ndzwv23znm50ophchmy55-5-0.jpg

pair-t-tl7600-t-86103-deskphone-wg3ndzwv23znm50ophchmy55-5-2.jpg
pair-t-tl7600-t-86103-deskphone-wg3ndzwv23znm50ophchmy55-5-5.jpg
First of all TL7600 does not need pairing, it is a passive wireless i.e it remains in hunt mode till a deskphone actually pairs with it.

First things first - Charge the Dect Headset TL7600 for 1-2 hours. Press the On/Off button once and you will see a blue/red light that will keep blinking every 2-3 seconds. This shows that the headset is unregistered with the Deskphone. When the headset becomes properly paired and placed on the charger, it will show steady blue light.

Okie, now to registering the headset.

a) First, lets reset the TL7600 just incase it was paired to another phone. Even if it is not, lets just do a reset to avoid some problem.

Push these buttons in the following order one by one :

Push these buttons in the following order:
vol+mutevol-mutevol+vol-mute
b) Go to the TL86103 and keep TL7600 very close to it. Lift off the TL7600 off the charger and then put it back in.



c) Press "MENU" on telephone mode with phone handset on the phone and the phone in Idle Mode.

c) Scroll to "Settings" and then scroll to "Register"

d) All this while, the TL7600 should be on the charger. If you remove it from the charger, it will not register.

e) Within 90 seconds to 2 minutes, the headset will be registered and you will see the handset will be assigned a name on the phone.

f) Pick up the headset, switch it on and you will hear a dial tone.

g) If this doesnt work, try to first press hold for 10 seconds till it says "Unregister All Devices', Click Yes and go through the process again.

j) If you want to know how to make a call, please note that the call will have to made first on the deskphone, then switch on the headset and there you go. Either lift the reciever and make a call or press Speaker and make a call and then switch on the headset, put the deskphone handset down or switch off the speaker and your TL7600 will be connected.

*** For TL86106, everything is same till (b). After that, press HOLD Button on the phone for 4-5 seconds till you see "Registering". Within 90 seconds to 2 minutes, the device will register the TL7600.pair-t-tl7600-t-86103-deskphone-wg3ndzwv23znm50ophchmy55-3-4.jpg

Dec 31, 2015 | AT&T Lands Phones

1 Answer

Pairing at&t to uniden


Please note we do not test our products with third party accessories/products.

Jun 22, 2015 | Uniden Radio Communications

1 Answer

How do I put TL7600 in pairing mode


Watch this video and follow the instructions

Apr 30, 2014 | AT&T TL7600 Wireless Headset

1 Answer

How do i pairing a tl7600


*** How to Pair AT&T TL7600 with AT&T 86103 or 86109 !!!

If you have been going nuts on how to pair TL7600 with TL86103 or TL86109 Deskphone, here is a detailed answer.






First of all TL7600 does not need pairing, it is a passive wireless i.e it remains in hunt mode till a deskphone actually pairs with it.

First things first - Charge the Dect Headset TL7600 for 1-2 hours. Press the On/Off button once and you will see a blue/red light that will keep blinking every 2-3 seconds. This shows that the headset is unregistered with the Deskphone. When the headset becomes properly paired and placed on the charger, it will show steady blue light.

Okie, now to registering the headset.

a) First, lets reset the TL7600 just incase it was paired to another phone. Even if it is not, lets just do a reset to avoid some problem.

Push these buttons in the following order one by one :

Push these buttons in the following order:
vol+mutevol-mutevol+vol-mute
b) Go to the TL86103 and keep TL7600 very close to it. Lift off the TL7600 off the charger and then put it back in.



c) Press "MENU" on telephone mode with phone handset on the phone and the phone in Idle Mode.

c) Scroll to "Settings" and then scroll to "Register"

d) All this while, the TL7600 should be on the charger. If you remove it from the charger, it will not register.

e) Within 90 seconds to 2 minutes, the headset will be registered and you will see the handset will be assigned a name on the phone.

f) Pick up the headset, switch it on and you will hear a dial tone.

g) If this doesnt work, try to first press hold for 10 seconds till it says "Unregister All Devices', Click Yes and go through the process again.

j) If you want to know how to make a call, please note that the call will have to made first on the deskphone, then switch on the headset and there you go. Either lift the reciever and make a call or press Speaker and make a call and then switch on the headset, put the deskphone handset down or switch off the speaker and your TL7600 will be connected.

*** For TL86106, everything is same till (b). After that, press HOLD Button on the phone for 4-5 seconds till you see "Registering". Within 90 seconds to 2 minutes, the device will register the TL7600.

Nov 07, 2013 | AT&T TL7600 Wireless Headset

1 Answer

TL7600 Headset will not pair with TL8802 base


*** How to Pair AT&T TL7600 with AT&T 86103 or 86109/TL88002 !!!

If you have been going nuts on how to pair TL7600 with TL86103 or TL86109 Deskphone, here is a detailed answer.

First of all TL7600 does not need pairing, it is a passive wireless i.e it remains in hunt mode till a deskphone actually pairs with it.

First things first - Charge the Dect Headset TL7600 for 1-2 hours. Press the On/Off button once and you will see a blue/red light that will keep blinking every 2-3 seconds. This shows that the headset is unregistered with the Deskphone. When the headset becomes properly paired and placed on the charger, it will show steady blue light.

Okie, now to registering the headset.

a) First, lets reset the TL7600 just incase it was paired to another phone. Even if it is not, lets just do a reset to avoid some problem.

Push these buttons in the following order one by one :

Push these buttons in the following order:
vol+mutevol-mutevol+vol-mute
b) Go to the TL86103 and keep TL7600 very close to it. Lift off the TL7600 off the charger and then put it back in.


*** FOR TL86103, do the below (See below for other models)

c) Press "MENU" on telephone mode with phone handset on the phone and the phone in Idle Mode.

c) Scroll to "Settings" and then scroll to "Register"

d) All this while, the TL7600 should be on the charger. If you remove it from the charger, it will not register.

e) Within 90 seconds to 2 minutes, the headset will be registered and you will see the handset will be assigned a name on the phone.

f) Pick up the headset, switch it on and you will hear a dial tone.

g) If this doesnt work, try to first press hold for 10 seconds till it says "Unregister All Devices', Click Yes and go through the process again.

j) If you want to know how to make a call, please note that the call will have to made first on the deskphone, then switch on the headset and there you go. Either lift the reciever and make a call or press Speaker and make a call and then switch on the headset, put the deskphone handset down or switch off the speaker and your TL7600 will be connected.

FOR TL86106, 86109 and 88002, do the below steps.

*** For TL86106, everything is same till (b). After that, press HOLD Button on the phone for 4-5 seconds till you see "Registering". Within 90 seconds to 2 minutes, the device will register the TL7600.

Aug 06, 2013 | AT&T TL7600 Wireless Headset

1 Answer

Phone cannot find headset


Be sure the the headset in in 'Pairing' mode.
When in pairing mode, the light should be flashing red and blue or have a steady blue.
The put most headsets in pairing mode, turn headset OFF, then hold the power button until it goes into pairing mode as discribed above.
Then you can discover it with your phone.

Mar 11, 2010 | Samsung Bluetooth?® WEP200 Headset...

1 Answer

Pair bluetooth em227 with my phone


Be sure the the headset in in 'Pairing' mode.
When in pairing mode, the light should be flashing red and blue or have a steady blue.
The put most headsets in pairing mode, turn headset OFF, then hold the power button until it goes into pairing mode as discribed above. Then you can discover it with your phone. Pin (pass key) should be 0000 (4 Zeros) or try 1111, 1234, 9999

Mar 05, 2010 | Southern Telecom Emerson Bluetooth Headset...

2 Answers

I don't know how to pair it to my mobile phone..need to put the headset inot pairing mode??


Yes. To put your headset into pairing mode:
1.) Make sure your headset is off.
2.) Hold the Power Button on until the blue light stays lit (about 8 seconds). This puts it into pairing mode.

Nov 05, 2009 | Samsung WEP170 Wireless Headset

1 Answer

I am unable to pair my bluetooth with nokia 5310 music xpress


Be sure the the headset in in 'Pairing' mode.
When in pairing mode, the light should be flashing red and blue or have a steady blue.
The put most headsets in pairing mode, turn headset OFF, then hold the power button until it goes into pairing mode as discribed above.
Then you can discover it with your phone or PC. Pin (pass key) should be 0000 (4 Zeros) or try 1111, 1234, 9999

Oct 16, 2009 | Nokia Bluetooth Headset BH-207 Wireless...

1 Answer

I can't pair my motorola h681 bluetooth and my SGH -A837


Be sure the the headset in in 'Pairing' mode.
When in pairing mode, the light should be flashing red and blue or have a steady blue.
The put most headsets in pairing mode, turn headset OFF, then hold the power button until it goes into pairing mode as discribed above.
Then you can discover it with your phone or PC. Pin (pass key) should be 0000 (4 Zeros) or try 1111, 1234, 9999

Jun 08, 2009 | Motorola Mobility H550 - Bluetooth Headset...

Not finding what you are looking for?
AT&T TL7600 Wireless Headset Logo

Related Topics:

2,424 people viewed this question

Ask a Question

Usually answered in minutes!

Top AT&T Radio Communications Experts

eradiostore
eradiostore

Level 3 Expert

1646 Answers

Brad Brown

Level 3 Expert

15441 Answers

Mike Charette

Level 3 Expert

1795 Answers

Are you an AT&T Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...