Ipaq 3650 I replaced the touch panel only. It is the glass gover with a sensative plastic sheet ans a connector on it. four wire leed and can only go in one way. the only number I see on the original is "94 HIT AR B5". I purchased the replacement from AX micro solutions "1paq h3600 & h3700 series digitizer/touch panel" HP1023. Thanks for your help. Bill

There is a poor diagram on Searspartsdirect.com, but no instructions. A diagram might help.

did you read out the thermal fuse with a meter?if not buy a meter or you'll end up changing parts you don't need,if you changed out the fuse and still have no heat then your old fuse was good and you have another problem,buy a meter,pull off at least one of the wires,set the meter on say 20k ohms,you'll see a 1 one the meter,touch the leeds together and you should see anything but 1,now touch the leeds to the part you're checking with at least one of the wires or both removed,if you see the 1 the part is bad,if you see anything other than 1 the part is good,next time send the full model number off of the machine you're having problems with so whoever is helping you can look up your machine,BUY A METER,don't replace parts you don't need,if you have no heat and you changed out the thermal fuse check the element and the fuses on the heater box,you'll see two red wires going to the heating element,pull one wire off,touch the meter leeds one to each connector on the element,if you see 1 the element is your problem.

The glass you refer to will be laminated and the muck is growing in the plastic that bonds the 2 pieces of glass You will have to replace that piece of glass.

"Replacing fog light bulbs on 2013 Santa Fe". Raise vehicle if you are a big person. In front of front wheels triangular plastic panels exists. Remove Phillips head plastic screws in chosen panel (2ea). Pull panel down. Stick hand through opening, remove wiring connector from bulb. (Bulb will not come out unless you do). Twist bulb housing counterclockwise and remove. Install new bulb, reverse procedure and don't touch the glass part of the bulb.

Using a wire cutting tool, cut and remove the outer sheath of the coaxial cable approximately 1/2-inch down from the end of the cable. Take care not to cut too deep or you will damage the aluminum sheeting and perhaps even the plastic wire insulation. Peel back the aluminum sheeting so it wraps around the outer sheathing and remove about 1/4 inch of the white plastic wire insulation using the wire cutting tool to expose the thin cable wire.

Attaching Connector

Slide the ferrule ring, which is the metallic piece used to hold the connector on the cable, onto the coaxial cable. Push the connector onto the cable so the white plastic wire insulation rests up against the inside of the connector. Slide the ferrule ring forward so it covers the bottom end of the coaxial connector.

Finishing

Crimp the ferrule ring tightly around the wire and the connector. You may notice that some of the aluminum sheeting that you pulled down sticks out of the bottom of the ferrule ring. Trim the sheeting before using the cable.

Contact Ricoh . Those touch screens are failing at almost a 100 percent rate. You do not have to replace the entire consol, just the glass panel that has the touch sensative plastic coating.
I believe those are being replaced free by Ricoh.
Very easy to replace also.

Window Regulator, Rear Door, Explorer Removal

1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .

Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation

1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.

1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.

1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .

1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .

1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.

1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
   
   

1. If equipped with power windows, disconnect the wire from the regulator.

1. Remove the rear door window glass as described in this section.

1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.

1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
   

1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.

1. Remove two upper regulator attaching nuts.

1. Remove regulator from the front door (20125) .

Installation

1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.

1. Install regulator into access hole in inner panel.

1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).

1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).

1. Install two upper regulator attachment nuts.

1. Install door glass as outlined under Door Glass Installation.

1. Adjust glass as outlined under Adjustments .

1. Reconnect wire to regulator, if equipped.

1. Check operation of window regulator.

1. Install door watershield and trim panel. Refer to Section 01-05B .

Y have a similar case, after replacing the LCD screen of one of my customers. The image is upside down and mirrored. We are going to test a new panel.
I'll let you know.

Could you write down the part number for the old and new screens to check for compatibility?
Regards,

The touch screen is a 4 wire resistive type made up of several layers. A thin plastic layer, a micro thin metal layer, microdots for insulators, another ultra thin metal layer, and a final plastic layer. All of these layers amount to the thickness of a sheet of paper. This whole stack is bonded to a thin sheet of glass and placed over the actual TFT display.

It's amazing that you can see through all these layers and only lose 20% of the light. What's not so amazing is that those thin metal layers are prone to damage. I've seen several with no apparent damage that didn't work, and several with visible scratches or cuts that worked fine.

I usually start by installing (or reinstalling) v7.2 firmware and then attempt to recalibrate the screen, sometimes that works. Next I would try re-seating the 4 conductor touch screen pigtail in it's ZIF socket nestled between the big white wires on the display assembly. The last resort is to buy a broken 2600 or 2700 series Garmin and salvage the touch screen. You could send it to Garmin for a flat $250, but that makes no sense at all.

If you get another screen (Garmin won't sell you one), Here's how to replace it:
Remove the six screw holding the case together.
Split the cases and pull the patch antenna out of it's slot.
Remove the four silver screws holding the display assembly into the front bezel.
Unhook the small ribbon cable that goes to the infrared receiver under the red lens.
Pull the display assembly out of the front bezel. It won't come all the way out because of cables.
Use a razor to cut the plastic tape holding the touch screen bracket to the TFT display.
Unlatch the 4 conductor ribbon from the ZIF connector nestled between the 2 big white wires.
Use a penknife to unbend the metal tabs keeping the touch screen from coming loose. I usually just do the two by the IR receiver.

When you reassemble, don't get frustrated with the gaskets, they're tricky but it can be done. Tom