Question about Coffee Makers & Espresso Machines

2 Answers

Durabrand (model # cm4113d) coffee maker

My durabrand coffee maker with model number cm4113d is not working...it heats up, but no water drips into the pitcher. it was working fine yesterday..please give me some tips or something to help me. thank you

Posted by on

  • puppy dog Aug 24, 2008

    I have a bunn dual 120/208v1set mach #rf rn 200900 0008 serial # dual 204038 0899. the coffee machine when you push start button it will make half pot then it stops drip water and the timer still calls for water and if you try the other side nothing and this unit has a water Pickett no water either.I have taking unit apart and de-limed and rebuilt valves all of them. Wait about one hour then you get a half pot then the same thing.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The dual bunn unit that gives a half pot then runs out of water. I replaced the liquid level board, and fill tube in tank and the hose from solnold to fill tube. reset timers for water on timer board. unit work like new.

Posted on Nov 29, 2008

Use Coke, put 200ml in water tank and leave overnight, then empty and rinse with tap water

Posted on Jun 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Why does coffee come out while pouring in water its a bunn 10 cup coffee maker


The Bunn has a little stopper that closes the water drain port in the reservoir while the lid is open. You can see a little white plastic pin protruding up out of the grate with the lid open. When you close the lid, it pushes on that pin which causes the stopper to lift off the drain port, allowing the water in the reservoir to enter the heating tank.

If water is entering the coffee basket BEFORE the lid is closed, then something is wrong with that little stopper. It may have a chunk of debris on it preventing it from sealing, or it may be deteriorated, torn, disconnected, etc.

Only way to know is to remove the the screws in the grate and pull the top off exposing the reservoir, and the stopper assembly. The little plastic flapper disc should be seated in the reservoir drain port. It should be relatively flat (not wrinkled) and covering the drain port completely. Test it by pouring some water into the reservoir. If it drains out without you activating the stopper, then a repair is needed.

Move the lever up and down and check its operation. The arm must move freely and close when released. There should be no dirt or debris on the sealing surface of the flapper nor on the sealing surface of the drain port. Gently clean with vinegar as necessary. If the seal is damaged, then a replacement is required.

Nov 29, 2014 | Bunn 10 Cup Home Coffee Brewer

1 Answer

Espresso maker continually leaks when heating


Most likely a gasket problem. But you say that it drips water while it heats. Try it without the coffee holder; it shouldn't leak.

Jul 16, 2014 | FrancisFrancis! Coffee Makers & Espresso...

1 Answer

Water heats. blue lights work. only drips come out. put vinegar in. 10 drips come out.


Hi,

Here is a tip that I wrote that will give you some things to try that will helpyou get your Keurig coffee brewer workingagain.

Keurig CoffeeBrewer not making a full cup of Coffee
heatman101


';

Aug 07, 2011 | Keurig B60 Coffee Maker

1 Answer

I have a commerical Bunn coffee maker. I ran vinegar to clean it out. It dripped very slow. Now, I get a 6 minute pot, the coffee is 180 degrees, but the coffee is very weak! What is up?


Coffee maker is not pre-heating the water.The brew cycle should take about two minutes, and the coffee should be 200°F when it comes out, that is why it's weak. To clarify, is it a commercial model, or a home model (like the one pictured)? Home models will have a 'vacation switch' on the side of the unit that needs to be on to get the water pre-heated properly.

Jan 19, 2011 | Bunn 10 Cup Home Coffee Brewer

2 Answers

A Krups KM7005 coffee maker/grinder doesn't heat or drip water .


Mine had the same problem ... all the lights are on, grinding works fine, but no heat on the plate, and no dripping of water.

After a weekend on the workbench, I mastered this machine. The KM7005 has 2 x MicroTemp G4 thermal cutoff (TCO) fuses which interrupt the Live line, for overheat protection. Mine didn't overheat per se, but the TCO blew anyway. Not reset-able ... need to be replaced with a soldering iron. To date, I have helped 13 people on this site fix this exact problem.

I'll be happy to advise you to fix this, or fix it for you. Write me at KM7005@flightsystems.biz.

Dec 16, 2009 | Krups Small Appliances Espresso Machine

1 Answer

My coffee maker won't brew the coffee. Mr.Coffee GBX25


you tube is clogged pour in 2 cups of vinagar an brew this will eat away the calcium deposits. in your coffee maker if you water is hard where you live you may want to by distilled water or use some type of filter or water softener

Jun 23, 2009 | Mr. Coffee TFTX85 Coffee Maker

1 Answer

My durabrand coffee maker (Model CM4113D) is not working. When turned on, the hot plate won't heat up and the water doesn't pass through the system. The on/off light lights up when turned on so I know...


I've owned a few of these models, and love them as they are for quick hotel cups of coffee... where, I need to make my own. Or I'm out on the road, and can quickly make a cup (with use of a generator).

I had one die, and it was the thermostat under the bottom plate (white thing, with two wires attached at each side). I simply bought another dirty 4113 online, and replaced my thermostat with my clean and hygiene friendly 4113... and threw the other maker away (keeping the pot of course as a backup spare).

For $13 new... you can't beat the price. However, I'd not trust it in my house or elsewhere for every day use. It's cheaply made, and has no fuse or circuit breaker in case of fault or shorts. It could be liable for your house burning down. So use with caution!!!
I still love mine, for what I use it for!!!

Dec 04, 2008 | Coffee Makers & Espresso Machines

1 Answer

Coffee maker parts


need a heating element replacement for model cm 500 coffee maker. How much does it cost? Mark
email to mmtazzy @yahoo.com

Sep 01, 2008 | Coffee Makers & Espresso Machines

Not finding what you are looking for?
Coffee Makers & Espresso Machines Logo

Related Topics:

673 people viewed this question

Ask a Question

Usually answered in minutes!

Top Coffee Makers & Espresso Machines Experts

Ernest R
Ernest R

Level 3 Expert

1618 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Sergio M Perez

Level 2 Expert

39 Answers

Are you a Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...