Question about Biostar 945GCM4 7x Motherboard

1 Answer

I JUST INSTALL A BIOSTAR 945GMCM4 7.X MOTHERBOARD AND WHEN I POWER UP THE VIDEO WOULD NOT DISPLAY NEITHER IS THE HARD DRIVE AND LED LIGHT LIT UP WHAT SHOULD I DO . I CHANGED THE PROCESSOR AND STILL NOTHING

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,571 Answers

Have you installed the front panel connectors correctly?
Are there any beeps?
Is the bios version correct for your CPU

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to connect panel 1 of n68s3+


PANEL1: Front Panel Header for Biostar N68S3+ from

http://www.biostar.com.tw/app/en/mb/introduction.php?S_ID=506#dl

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case's front panel switch functions. Pin #1 has a black square on the motherboard and the pins are oriented from 1-8, left to right, bottom row and 9-16, left to right, top row. You will notice that there is no #11 pin.

pin #'s

1-2-3-4 Speaker (1+, 4-)
5-6 hard drive LED (5+, 6-)
7-8 reset switch (7-, 8+)
9-10-11 N/A (not used)

12-13-14 power LED (12+, 14-) ** only if power wire is 3 port connector **
13-14 power LED (13+, 14-) ** only if power wire is 2 port connector **

15-16 power button (15+, 16-)

Did this solve your problem?

Dec 22, 2012 | Biostar N68S3+ AM3 NVIDIA MCP68S Micro ATX...

1 Answer

I have installed a new motherboard in an acer case. The power cable from the switch on the front of the case will not connect to the board. Can anyone help? Thank you


You should read the motherboard manual, for cabling:
1. Power SW
2. Reset SW
3. HDD led
4. Power led - and power led +
5. Speaker

Cabling scheme, also written on the motherboard.

If the Power SW not installed the switch on does not work.
If the Reset SW not installed the switch reset does not work
If the HDD led
not installed the hard drive light (red) is not lit
If the Power led (+/-) not installed the power light (yellow) is not lit
If the Speakers are not installed, when the computer is on the beep sound is not heard.


I hope this information helps.

10_15_2011_9_30_03_pm.jpg

Oct 15, 2011 | Computers & Internet

1 Answer

There was no beeep sound heard at the beginning Delay in turn fan power supply the Power LED on the front panel of the computer doesnt light the HDD LED on the front panel of the computer doesn't...


as i always say:
intercept all of cables of your PC case and even power cable of your monitor.
evolve battery of bios then wait for 25 minutes then connect all of cables and try turning on your PC:
1- with battery of bios
2- without battery of bios
it should work.
(this works cause the motherboard reset it's bios and start correctly again).

Jan 13, 2011 | Biostar TF7100P-M7 Motherboard

1 Answer

When i turned it on led 1 error appeared but memory is already installed


If only Led 1 light is lit then you have a memory error. You either have your RAM seated wrong,
or you have the wrong ram installed. look in your users manual or go to the Biostar site
and get the recommended DDR3 or DDR2 matched pairs one or the other, not one of each.
Capiche?

Jul 27, 2010 | Biostar TP45E Combo Motherboard

1 Answer

IT POWERS UP BUT THE HARD DRIVE LED DOESN'T LIGHT AND NO DISPLAY ON MONITOR


check cable check board for wire to jumper video card replace it jim

Mar 08, 2010 | Biostar M7VKQ Motherboard

2 Answers

Dont know where to hook up the power and leads on the p4m80 -m4 to get power


missed placed the manual of the m935dlu motherboard having problem hooking up the panel switches the led sw, hhd sw, reset sw, suspd led and pwr sw

Jun 29, 2009 | Biostar P4M80-M4 Motherboard

2 Answers

My PC does not start.


When you say "does not start", does that mean none of the fans spin, the hard drive does not power up, CD drive door won't open, no lights light up on the motherboard?

If any of these are happening, let me know. I would start by unplugging all the things you added except the CPU fan first and see if it now powers up.

If it is indeed powering up, but there is no display, perhaps the video card is not properly seated (assuming video is not integrated). Also, you did not mention if you had plugged in keyboard, mouse or any other peripherals.

Start with as little as possible and when you get power, add one item and check, then add another and check.

Let me know if you need more help.

Honest1abe


Jan 06, 2009 | Biostar P4M890-M7 Motherboard

Not finding what you are looking for?
Biostar 945GCM4 7x Motherboard Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Biostar Computers & Internet Experts

Jayburt

Level 2 Expert

78 Answers

David
David

Level 3 Expert

781 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Are you a Biostar Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...