Question about Marantz Audio & Video Receivers

1 Answer

How do i change the belts - Marantz Audio & Video Receivers

Posted by on

  • Graeme Ross
    Graeme Ross May 11, 2010

    Hi d4evil

    What make and model of tape deck are you wishing to service?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,512 Answers

Hey d4, you still need some help with that?


Posted on Jun 29, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Occasionally when my dryer is running it makes the most awful high pitched screeching noise! Help! Not even sure what to do or look at to resolve this issue.

It'll either be the drive belt that goes around the drum needs replacing or the idler pully that keeps tension on the belt needs replacing. It is usually the belt. This is not a difficult replacement. A generic procedure is to remove the back of the dryer. You should be able to get to the belt to replace it. While you're in there, check the pully for smoothness of operation and that it rotates easily. If it needs replacing also, do it while you're changing the belt. If the belt seems to be in good condition, the pully might just need a drop or two of light oil.

Jan 03, 2011 | Audio & Video Receivers

6 Answers

Technics RS-CH770 double tape decks not spping round/working

Please check Capstan Motor working / rotating. If no, check its supply volts. If yes, then check Capstan Belt and FR Belt, should not be any cracks on it. If found cracks, please replace them.

Aug 13, 2008 | Technics Audio & Video Receivers

1 Answer

The drive belt off my AWA turntable has come off and I cannot re-configure it

undo clip on centre of deck circlip normally (round clip) remove deck platter round plastic that records sit on...when removed turn over replace drive belt if brokern . if just come of place belt around the inner circle so there are no twists etc on the belt ....look at near outer edge of platter there is a clip you can stretch belt to to hold so you can put over drive motor...(belt stretch from centre to clip creating v with the bely as you veiw from above ..locate motor on the deck noe alifn top of v with positin above motor .. when done drop down platter onto centre shaft again.gently turn the platter clock wise until belt locates correctly with deck ..replace clip and test ..if ok done ..if not repeat until you get it right....sometimes over time belts stretch so a new belt may be required ..ebay can supply most belts . type in turntable drive belt ..measur size of belt by cutting is it..(if strectched and no use) measure lenght of belt find replacement belt that is smaller than measurment .i.e nearest size ...hope this helps yammandan

Aug 19, 2010 | Audio & Video Receivers

1 Answer

Need belts for

Your best bet is to contact MCM electronics and use their cross-reference service to get a more common belt number. They should have the belts that you need. I would give you the numbers, but I don't have a listing for your specific model.

Keep us posted.


Mar 03, 2009 | Optimus Audio & Video Receivers

1 Answer

I have teac reel to real tape recorder. It drags in play mode and the speed is wrong. Do I need to change the belt?

Most likely .
All the belts should be changed out and wheels/rubber rollers need cleaning.

Jan 05, 2009 | Teac DRH300DAB Receiver

2 Answers

I need help to replace the belt in my Teac C-3X

Hi rjwolfe

You can get a complete set of drive belts from here

There is a great instructional guide by the same guy here.

I am more than happy to answer any other questions you may have about it, just give me a hoy :) If you are still unsure, or have problems, then before you give a rating for this advice, please get back to me and we can try some more things.
Thanks for using FixYa, If you consider the advice I have given you as sound, a FixYa rating is a great reward for my efforts to help you. Cheers.


Jun 22, 2008 | Teac Audio & Video Receivers

1 Answer

Turn table not going round on a Sharp VZ-1900E?

Please help as I have this problem too and can't see how to get into it to change the belt

Apr 15, 2008 | Sharp Audio & Video Receivers

3 Answers

JVC turntable LA10

The trick is to lift up on the platter (tothat metal on metal feel that you had) while simtaneously "lightly" tapping on the top of the shaft with a hammer. Trust me it will work as just changed my belt.
Hope that helps.

Mar 16, 2008 | Audio & Video Receivers

1 Answer

The fish on my fisher price ocean aquarium have stopped turning. I've changed the batteries and everything but that works, help!

I think there is a belt or gear in there that might have broken. I am familiar wih that cute little "aquarium" that shines a light up through the liquid.

Mar 04, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marantz Audio & Video Receivers Experts


Level 2 Expert

180 Answers

Pieter Vleeshouwers

Level 3 Expert

1410 Answers


Level 3 Expert

60769 Answers

Are you a Marantz Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides