Question about LogiSys 5.25" Multifunction Panel with Fan Control, Temperature Display, Power-On Remote Control, US... (FNCOXP3F80SL)

1 Answer

What is the red /white wire for that comes out the back ,marked H.H.D Led ? where does it go

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 40 Answers

Actually the HDD led was nothing all about.. it will just support the hard disk to have power.. if you have a good power supply and you trust your power supply .. the hdd led is no use..

Posted on Oct 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I trying to connect my SFC-4160 (security first color ccd camera) the wiring has been cut n there is 5 wires black,red,yellow,white and a bare wire ???? help


Inside the camera is a 4 pin connector connected to the LED Board, with the connector in hand, turn it till you see the pins inside the connector, from left to right wires 1st-white, 2nd-black, 3rd- bare wire or shield, 4th-red, yellow is not connected, the RJ45 end, face the latch away from you, wires are 1st-red, 2nd-white, 3rd-yellow, 4th-shield(bare wire), 5th-black, the LED Board has the wire positioning marked,,,,,

Nov 27, 2012 | Car Audio & Video

1 Answer

T6216


There should be 2 rows of pins in parallel usually around the bottom edge of the motherboard. The markings for which is which should be next to them on the board. HDled+, HdLed-, PwrSw, PwrLed, or something similar.

If you do find them but the hard drive Led does'nt come on it's because the plug for it needs to be turned around the opposite way, Led's only work one way as they are diodes. Same for the Power Led.

If there are no letters near the pins then you would have to find the motherboard manual.

Jan 28, 2012 | E-Machines eMachines Desktop PC

1 Answer

I have a 3 prong plug and 3 wires w/ connectors and they are not marked.which one attaches to the red, white, black terminal in the back of the dryer?


Looking at your dryer's wiring terminal block, you'll see three separated terminals. The red and black cord wires attach to the two outer terminals (it doesn't really matter which goes where), and the white one gets attached to the center one. You may even see smaller white wires coming from the back of the terminal and disappearing into the dryer. Make sure the terminals are securely tightened before you plug it in.

Dec 24, 2010 | Maytag Centennial 7.0 Cu. Ft. 7-Cycle...

1 Answer

What colors are the wires for the pwr sw, smi,rst,hdd led,grn led and where so i plug them in at s7sen 15-a01-013010 rev 3.0a


- the colors of the wires (can differ, depends on the case type):
  • Green(+ is the colored wire)-White(-) --> POWER LED (GREEN light)
  • Red-Black -> POWER SWITCH
  • Red-White -> HDD LED (RED light)
  • Blue-White -> RESET
  • Red-Black (4 pins wide)-> SPEAKER

df64004.jpg

Sep 03, 2010 | EliteGroup K7SEM Motherboard

2 Answers

I had a repairman come in yesterday. Said my


12 o'clock red...4 o'clock blue...3 o'clock white .( the white , has the smaller terminal )

Oct 24, 2009 | Whirlpool GS6SHAXLQ 25.5 Cubic Foot Side...

2 Answers

Blue LED light connection from Bezel to Motherboard


red white is the pair that supplies power it should be 2pin socket on motherboard

Sep 19, 2009 | E-Machines T6520 PC Desktop

2 Answers

NEED POWER SWITCH WIRING FOR A EMACHINE T-3095


check on the motherboard there should be a small prints on it near control panel.

Mar 05, 2009 | E-Machines eMachines T3830 PC Desktop

5 Answers

Gigabyte GA-8INXP Motherboard Problem- front connector pins


If the wires from the reset switch is white/blue the blue wire is positive, Hdd red/white red is positive power Green/white Green is positive etc. The wires on the speaker connector will be red/black/black/white - red is positive. The colored wire is always positive. On all GA mb's the positive connection is always towards the back of the MB and are marked with a + on the base of the pin as you can see on the photo. Hope this help.

Sep 19, 2008 | Gigabyte GA-8INXP Motherboard

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top LogiSys Computers & Internet Experts

Brett Duxbury
Brett Duxbury

Level 3 Expert

3592 Answers

Eric Andersen

Level 2 Expert

72 Answers

Julie Clark
Julie Clark

Level 2 Expert

68 Answers

Are you a LogiSys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...