Question about Schaerer Siena Espresso Machine

2 Answers

My display says select beverage heating steam. I can pour shots of espresso but no steam or hot water will dispense

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 38 Answers

Heating Steam The steam boiler has fallen below set point... could be tripped hi -limit .. steam relay faulty

Posted on Dec 21, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 29 Answers

Firstly, try to reset the overheat Klixon on the side of the steamboiler. Sometimes they can trip out if they overheat. Once you open the lid cover. You will see the round over heat stat with 2 wires going to it and right in the centre there is a little button that will be popped out, this needs to be reset by pressing it in.
If this is not tripped out, then you need to check the boilers element for resistance using a multimeter to make sure it is ok, I think on those boilers it should be about 45ohms but i'm not 100% sure on that figure? The hot water boiler and steam boiler on these machines are the same so you can check the resistance is the same on both.

If this doesnt help, please provide more details of the fault and I can try to further assist you.

Posted on Mar 20, 2014

  • markybean Mar 20, 2014

    Firstly, try to reset the overheat Klixon on the side of the steamboiler. Sometimes they can trip out if they overheat. Once you open the lid cover. You will see the round over heat stat with 2 wires going to it and right in the centre there is a little button that will be popped out, this needs to be reset by pressing it in.

    If this is not tripped out, then you need to check the boilers element for resistance using a multimeter to make sure it is ok, I think on those boilers it should be about 45ohms but i'm not 100% sure on that figure? The hot water boiler and steam boiler on these machines are the same so you can check the resistance is the same on both.



    If this doesnt help, please provide more details of the fault and I can try to further assist you.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When machine is turned on from the off position it does not go into rinse mode message comes up to hot please wait and yet the machine has been turned off for at least 20hrs


the power on sequence for the XP9000 is
1) Internal diagnostic
2) if no cold water, display notice and wait for water level in cold water tank
2) if water heating block is not hot, display notice and wait for block temperature
3) display "Rinse Press Hot Water" notice and wait for button press
4) rinse
5) display "Select Beverage" and wait for button press, ground coffee flap, or other input switch state change.etc...

in short... its doing what its supposed to.

Please consider reading the manual supplied wih your XP9000 or downloading the manual if you don't have it.

Nov 10, 2011 | Krups Super Automatic XP 9000 Espresso...

2 Answers

When you press the coffee button the machine grinds the beans, but then the water comes out the steam wand... please help


The problem is a very frequent one a small scale part have been moved and it stack to the water steam valve and it blocking it from closing completely. So when you make coffee the hose of water for coffee is in parallel with hot water steam wand and since the valve remains partially opened the water for coffee find easy escape from steam wand.

So we suggest to perform one more descale and it may need twice hopefully this small scale part to be dissolve a little bit more in order to pass thought the steam valve and thus the valve can close again completely. If you are not so lucky the part remain on the valve then only solution is to disassemble the machine thus clean the steam valve manually. In this solution you may find out that the valve o ring might be damage and thus the leak.
here is the link with steam valve parts and this the parts diagram of the machine and here many more for your machine

Aug 15, 2011 | Saeco Magic Comfort Plus Espresso Machine

1 Answer

Hi all. In desperate need of help. I have a La Cimbali M29 Select. I am unable to get hot water from the hot water tap and when the machine dispenses a shot of coffee, I have to turn the machine of...


From your description it sound that the button strip need to be replaced. All the buttons of the coffees and also for hot water are all set in one unit the button strip. This like a membrane and is located under the buttons. This is frequent problem with m29 select since the connector of the button strip it is exposed under the cup warmer area and is very easy to absorb the humidity from steam escape inside the machine and when one short circuit it happens then since the whole strip is one unit it will mull faction as you described.

Jun 14, 2011 | Espresso RMI La Cimbali Espresso Machine

2 Answers

It shoots too much water coffee come out watery


try adding more coffee to the filter, or making the grind FINER or both

Mar 08, 2011 | Coffee Makers & Espresso Machines

1 Answer

RE: F9 Upon startup the unit goes thru the normal cycles for making an expresso but, after the beans grind, little to nothiing is dispensed. The unit stops and the message is to fill water portion. I push...


Hi Bill
What happens when you do a tea ? (hot water only, NOT the steam button) do you also get little water ?
The fact that you are getting steam is good as there are 2 heating systems in the unit.
Have you ran the descaling recently (if you do not use filter ) ?
If you have or use a filter the problem is likely to be at the rear of the machine, however the back contents all the power and you will need to be happy to do some stripping down of the machine,
In the back you have the pump, valves, heater etc.
I am just about to draw up a flow chart of the water system inside the machine and have it published online (couple of days).
Are you happy to strip machine down ?

---


Please dont forget to vote if you liked my answer


thanks

------




Feb 12, 2011 | Jura Capresso Impressa F9 Espresso Machine

1 Answer

I have a miele cva620 ind it displays expel air.. what shall i do? how can i do it?


FIll the water tank.

Turn the program selector to "ON with light" and place containers below the hot water dispenser and the steam nozzle.

Press the hot water button, turn the steam selector counterclockwise and let water run out until it streams steadily.

Press the hot water button again.
Turn the steam selector to "o" to shut off the water.

That should solve the problem

Jun 25, 2009 | Miele CVA615 Espresso Machine

1 Answer

No coffee dispensed and no water comes out when Rinse selected


1st use cleaning tablets used for brew unit. and go on cleaning procedur.
2-the sound you hear i think is only motor of
grinding
thank you

Mar 24, 2009 | Miele CVA615 Espresso Machine

1 Answer

The coffee maker doesn't work - all the lights, timer, on/off switch, etc., seem to be working, but the water doesn't pour through the grounds to make the coffee


Does it make steam or can you hear the water boiling? Try and pour 4 cups of vinegar or lime away in it if it is clogged or plugged up from lme or mineral deposits, if it not getting hot( you can tell very easily by seeing if the plate the pot sits on is getting hot) then the thermocouple or heating element is shot.

Jan 26, 2009 | Krups 888 Centro

1 Answer

How do I descale the saeco magic deluxe coffee machine?


Hi,

Try this:

Standard descaling
Switch off the machine.
Pour a descaling product into the water tank.
Switch the machine on to the programming mode(see below). Place a large container under the steam/hot water dispensing tube and open the steam/hot water knob slowly, turning it counterclockwise.
Turn on the machine by pressing the main switch and let the descaling product flow out of the dispensing tube for approx. 1 min.
Close the knob again.
Turn off the machine with the main switch and let the solution take effect for approx. 5 minutes.
Repeat this procedure two or three times, to allow all of the descaling product in the water tank to flow out of the dispensing tube.
As soon as descaling has been carried out, rinse the tank thoroughly and fill it with fresh water.
Switch on the machine and let fresh water (approx. 2 l) flow out of the steam/hot water dispensing tube in order to rinse away residue.
The machine is now ready for operation.

When the machine is on, the warning light switches off automatically, by pressing the steam selection button for at least 5 seconds.

To enter the programming mode, turn the machine
off with the main switch.
Press steam , espresso coffee and the
main switch at the same time.

Release the buttons.

Hope this will help you.
/Mirran

Aug 16, 2008 | Saeco Magic De Luxe Espresso Machine

5 Answers

Trying to ventilate and hot water not flushing through on button 26


Before you press water button to vent you need to restore to factory settings.


First press menu (far right button) then toggle to restore factory settings (using far left button), press menu button then far right again until yes comes up, then press menu button. Press esc button (3rd from left), machine should now be back to normal. Then press water button (3rd from right) and turn steam knob to vent until free water is coming through.

This is the only way I could get mine to work!

Dec 30, 2007 | Gaggia Titanium Espresso Machine

Not finding what you are looking for?
Schaerer Siena Espresso Machine Logo

510 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schaerer Coffee Makers & Espresso Machines Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Kolbrun...

Level 3 Expert

1205 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Schaerer Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...