Question about Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

1 Answer

How do you get the chuck off - Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 268 Answers

Hello,

Here is a link that explains with illustrations how to remove the chuck.

http://www.ereplacementparts.com/article/890/How_to_Remove_a_Drill_Chuck.html

Hope this helps

Posted on Oct 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you remove or reset a stuck drill chuck


If it is a reversible drill there is almost certainly a left-handed thread screw or allen bolt through the centre of the chuck into the drill shaft and this must be removed before the chuck can be removed.

If it is a keyed chuck select low gear if there is one, fit the chuck key and then strike it sharply with a hammer to jar the chuck in an anti-clockwise direction. Usually it takes only a couple of blows before the chuck is loosened.

Keyless chucks are more problematic. I hold them in a vice and use the drill in reverse which has proved fairly successful, though sometimes the chuck is only fit for scrap afterwards.

Lots of the keyed chucks can be taken apart for cleaning and lubricating if necessary.

Aug 28, 2016 | Dewalt DC740KA Battery 1500mAh, 12V, Ni-Cd

1 Answer

Where can i find a 5/8 in. chuck for a Pit Bull CH-16NF Drill press


Take it to a local engineering sales shop. They are all basically the same and fit into the shaft with a morse taper. You just need the correct taper.

  • 5/8 in. Keyed Drill Press Chuck ' Princess Auto www.princessauto.com/en/detail/5-8-in-keyed-drill-press-chuck/A-p...
    • 4.5/5
    • 2 REVIEWS
    Email Signup. Never miss a sale and receive special online only offers.
  • King Canada KDC-58M Chuck, Drill Press, 5/8" JT6 for ... https://eastcoastpowertools.ca/chuck-drill-press-5-8-jt6-for-milling King Canada KDC-58M Chuck, Drill Press, 5/8" JT6 for Milling At East Coast Power Tools
  • 5/8 in. Keyed Drill Press Chuck ' Princess Auto www.princessauto.com/en/detail/5-8-in-keyed-drill-press-chuck/A-p... Help others make a decision about this product by sharing your experience.
  • Related searches for 5/8 in. chuck for a Drill press
  • Woodstock D3455 Drill Chuck, 5/8-Inch by JT33 - Amazon.ca https://www.amazon.ca/Woodstock-D3455-Drill-Chuck-8-Inch/dp/B000HRXOLS This item: Woodstock D3455 Drill Chuck, 5/8-Inch by JT33 CDN$ 47.71. In Stock. Ships from and sold by Amazon.ca. FREE Shipping. ... (Canadian Tire) Drill Press.
  • 5/8 Drill Chuck ' eBay 2q== www.ebay.com/bhp/5-8-drill-chuck Suitable for drill presses or lathes spindle accepts R8 shank. Chuck key and R8-JT33 arbor are also included in the package. Special quenching treated ...
  • 5/8" Drill Press Chuck [MAG-DPC58] - $29.99 : KMS Tools ... https://www.kmstools.com/5-8-drill-press-chuck-2990 KMS Tools & Equipment from Vancouver BC 5/8 ... Home > Metalworking > Lathes and Milling Machines > Chucks and Taper Adapters > 5/8" Drill Press Chuck 5 /8 ...
  • 1 32 5 8 Heavy Duty Drill Chuck with Chuck Key and R8 Arbor Amazon com

    Jun 05, 2016 | Drills

    3 Answers

    How much wood would a woodchuck chuck if a woodchuck could chuck wood


    Well, that all depends on the dimensions of, not only the wood, but also the woodchuck itself. There are many different kinds of woodchucks out there and they all very in the amounts of wood it would be able to chuck if woodchucks could chuck wood. So let's start with the woodchuck itself.
    1.) Slimmer woodchuck would likely be able to chuck more wood over any given period of time while thicker (fatter) ones would lag behind the quantity of wood chucked, but they may be able to chuck it farther than their slimmer counterpart if that's any consolation.
    2.) A smart woodchuck would certainly get more chucking done than one of lesser intelligence because it would be much less likely that a smart woodchuck would get distracted from none wood chucking activities and events.
    3.) A friendly woodchuck would be more likely to chuck less wood than a grumpier woodchuck because the friendly woodchuck would want to help other's who were having trouble chucking wood while the grumpy woodchuck is only concerned with his own work.
    Now we go over the qualities of the wood that is being chucked.
    1.) If you have rather large pieces of wood, then the slimmer woodchuck may have more problems chucking it than the larger woodchuck and may, therefore, produce a lesser quantity of chucked wood.
    2.) The length of the wood would affect all types of woodchucks because if all the pieces of wood are of perfect length, then the woodchucks can get good leverage to chuck the wood and increase the wood chucking production.
    3.) The type of wood can also affect how well woodchucks chuck wood because lighter types, such as balsa, would be easier for woodchucks to chuck than would maple.
    These are the main factors to seriously consider when trying to determine how much wood a woodchuck could chuck if woodchucks could chuck wood, but there are other details that could be taken into account such as, location of the wood chucking, weather conditions of the wood chucking, and the surrounding environment of said wood chucking.
    I'm not sure how this relates to your Dell Latitude D410 PC Notebook, but I hope I helped!

    Jul 28, 2011 | Dell Latitude D410 Notebook

    1 Answer

    We have a chuck that got jammedand broken, is it possible to remove the chuck only and replace it or do u only get the whole front section with chuck. And if the chuck can be removed, how do u remove it....


    Hello,

    With the chuck open as far as possible, look within the jaws of the chuck for a bolt or screw head that attaches the chuck to the shaft. Remove the bolt/screw and remove the chuck. Some chucks can also be screwed onto the shaft, so look for signs of threads at the base of the chuck. Otherwise, once the bolt/screw is removed, tap along the outside around the chuck with a plastic hammer to loosen the chuck. Penetrating oil will help.
    Take your chuck with you to a "big box" type hardware store, where a replacement should be available. Any well stocked hardware store should be able to help you. I have found that the somewhat smaller hardware stores are usually staffed with knowledgeable persons, and getting a replacement ordered is easier. One is more likely to be stocked in the larger stores.
    The name brand of the chuck isn't as important for a replacement as is the correct shaft size and style of fit.
    Best regards, --W/D--

    Jun 15, 2011 | Chicago Pneumatic RP9790 STANDARD GRIP...

    2 Answers

    How can I replace the keyless chuck on my Dewalt DWD215G?


    Open the chuck wide open. In the center is a retaining screw, they usually have left hand threads. Remove the screw. Take an allen wrench1/4" to 3/8" in size and fasten the short side tightly in the chuck. The chucks are usually right hand thread, so take a small hammer and strike the allen wrench to turn the chuck to the left to loosen it. Once you have the chuck off, verify the thread size of the drill motor shaft, then go to McMaster-Carr and choose the one you need.

    Apr 16, 2011 | Dewalt DWD215G 12Inch 10AMP Heavy Duty Mid...

    1 Answer

    How to fix the bit


    If your Makita matches the one on the picture, you will need a chuck key to attach a drill bit or tool to the machine's chuck. The chuck key inserts to any of the small holes in the front part of the chuck and at the same time its teeth interlocks with the teeth of the chuck. When turning the chuck key you will widen or loosen the grip of the three jaw pieces, that clamps to your tool or bit. Tighten the chuck key by hand until the chuck grips the bit securely. For safety, unplug the power cord whenever operating the chuck key on the chuck.

    Jan 09, 2011 | Makita & 1/2 Inch Drill

    1 Answer

    3/8 Drill Driver, chuck replacement.


    hi friend,
    Step 1. Determine what kind of replacement drill chuck you want - a keyed chuck or key less chuck. Over the years, key less chucks have been widely used for handheld power tool drills, due to their improving grip torque and convenience.

    Step 2. If you prefer replacement key less chucks, then you have to know what type of key less chuck you will need - a single sleeve key less chuck or a double-sleeve chuck. You can simply determine it by checking your current chuck. If your current chuck is a keyed chuck or a double sleeve chuck, then you will need a replacement double-sleeve key less chuck. On the other hand, if your current chuck is a single sleeve chuck, then you should get a replacement single sleeve chuck.

    drill-chuck-sleeve-type.jpg

    Step 3. Confirm the threaded mount size (spindle size) on the chuck. 3/8"-24 threaded mount for 3/8" capacity drill chucks and 1/2"-20 threaded mount for 1/2" capacity drill chucks, but there are some exceptions where just the opposite may occur. To be safe, always check the threaded mount before you buy replacement drill chucks.

    drill-chuck-thread-mount.jpg
    hope this helps u
    please rate me.........................
    thank u for using fixya
    regards
    sivaranjini

    Nov 26, 2009 | Craftsman 19.2V C3 DRILL/DRIVER

    1 Answer

    Can't remove the chuck retaining screw.


    Place drill in vice with chuck in vice facing up . Clamp chuck lightly but with enough force to hold firmly.
    put allen wrench in chuck and lightly tap down to make good fit to allen screw head.Clamp chuck jaws down onto allen wrench lightly to hold wrench steady. Take piece of pipe to end of wrench,10".
    These chuck screws are tight. Hammer clockwise until screw brakes loose.Open chuck completely and remove screw.Chuck is threaded to spindle shaft . Place allen wrench with long end facing out of tool in chuck and tighten chuck securely. With hammer tap allen wrench sharply counter clockwise ( normal thread.)

    Jul 08, 2009 | Makita Drills

    1 Answer

    Drill chuck swap


    1. Turn the screw clockwise to take it out.
    2. Then you needs 3/8 allen key & insert the short side of the allen key & tighten the chuck.
    3. hold the drill at the edge of the table & wack the allen key
    counter clockwise & do it again as needed.
    4. dewalt keyless chuck will fit but you might add a washer to insure the chuck is not rubbing the clutch collar.
    5. putting it back together the other way.

    Jun 01, 2008 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

    1 Answer

    Dewalt dc920 repair instructions chuck


    To remove the chuck on your drill follow the instructions for the type of drill chuck you have:
    Instructions for removing a keyed chuck
    Most reversing drills have a left hand threaded screw located inside the bottom of the chuck.
    1.) If the unit has this screw place the chuck key, with the chuck facing toward you, into one of the holes on the right side of the chuck. Strike the key in a clockwise direction with a wooden mallet or similar object. This will loosen the screw inside the chuck.
    2.) Open chuck jaws fully. Insert screwdriver into the bottom of the chuck to engage screw head. Remove screw by turning clockwise this is a left-hand screw.
    3.) With the chuck facing toward you place the key into one of the holes on the left side of the chuck. Using a wooden mallet or similar object, strike the key sharply in a counter-clockwise direction. This will loosen the chuck so that it may be unscrewed by hand.
    There is no way to stop the motor from turning.
    It may require several attempts to loosen the chuck
    Instructions for removing a keyless chuck
    Most reversing drills have a left hand threaded screw located inside the bottom of the chuck.
    1.) If the unit has this screw open chuck jaws fully. Insert screwdriver into the bottom of the chuck to engage screw head. Remove screw by turning clockwise this is a left-hand screw.
    2.) Insert the short end of a 1/4" or larger hex Allen wrench into the chuck and tighten. Facing the tool strike the long end of the hex wrench sharply counter clockwise as it is a standard right hand thread. This will loosen the chuck so that it may be unscrewed by hand.
    There is no way to stop the motor from turning.
    It may require several attempts to loosen the chuck

    Oct 15, 2007 | Dewalt 18 Volt Compact Drill Kit

    Not finding what you are looking for?
    Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver Logo

    140 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dewalt Drills Experts

    Doctor PC
    Doctor PC

    Level 3 Expert

    7733 Answers

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Jim Thurston

    Level 3 Expert

    670 Answers

    Are you a Dewalt Drill Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...