Question about Dewalt 18 Volt Compact Drill Kit

2 Answers

My dewalt drill won't drive

My cordless dewalt will not drive a screw now. something in the unit is spinning but not the tip with the bit. is it the clutch?
thanks!

Posted by on

  • whiteykt May 30, 2008

    yes, the battery is charged and I've tried all settings. my thought was that it could be the clutch but wasn't sure. is this your best guess?

    thanks!

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 313 Answers

I bit the speed setting is not properly engage.

Posted on May 31, 2008

Is your battery is fully charge or maybe your clutch setting are too low. set it drill mode if it is not working you need to replaced
trans/clutch assy

Posted on May 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jaws won't tighten or loosen to hold a bit


Hmmm some times the counterclockwise screw that attaches the chuck to the drill come forward and that is how then it stucks the 3 parts that fix a drill to a chuck. Check if this screw come forward. If yes then destroy it and replace it... We destroy it by using a drill smaller than it (usually it is 5mm so we use 4mm bit and of course a CARBIDE one because even cobalt ones can not drill a hardened bolt)

Mar 26, 2012 | Dewalt 18v Battery Hammer Drill Dcd950...

1 Answer

Have a screw head stuck in the chuck .. it was a small bit and now wont pull out.... help


Just took apart a DeWalt, the chuck has a left hand scew that holds chuck in place, may be the problem

Jan 20, 2011 | Dewalt DW056 18 Volt Cordless Impact...

1 Answer

My driver will Work until the rachet starts then it just spins. What needs to be fixed on it?


If you begin to ratchet, and then the bit stops,and the drill is still running, the gearbox will have to be replaced. That is a part # 616908-03 and runs about 80.00

Here is a link to the DeWalt website where you can download the part diagram, take the unit apart, and verify that this is all you need.

http://servicenet.dewalt.com/Products/Detail/DW056K-2

Nov 21, 2010 | Dewalt DW056 18 Volt Cordless Impact...

1 Answer

How to take off a broken tip from impact drill dcf826


there are 4 hex screws the tip to fit it can be bought from most hard ware stores like drill dits they com in many different sizes. undo the screws and take of the tip toll be carefull to not not tip it downwards *** all the gears will fall out find the broken part take it out and replace with spare from dewalt supplys

best of luck sir

Aug 12, 2010 | Dewalt DW056 18 Volt Cordless Impact...

1 Answer

Was using with a spsde bi and hit a nail. Now


You may have inadvertently hit the hammer/drill switch and it is floating the middle between functions. This selector switch has a symbol showing a drill bit on one side and a symbol of the hammer on the other. Engage the switch bacK into the drill position

Jun 08, 2010 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

1 Answer

How to remove a chuck from a DeWalt hand drill


Open chuck all the way (like for a large drill bit). There should be a set screw at the bottom (where you would put a drill bit). Don't turn too hard - it may be a left handed screw (I don't remember if it is a lefty for sure but try gently each way then with a bit more force each way until it moves).

Good luck.

Mar 19, 2010 | Dewalt DC925B Heavy Duty Xrp 18V Cordless...

1 Answer

I have a DCD940KX 18v Dewalt drill driver with the one click drill chuck. It does not keep drill bits or screwdriver bits from spinning. They spin with the slightest bit of pressure on them. My questions...


this is not a common problem with dewalt. I have been using them in my construction business for years and only heard of this once or twice. I would go to their web site and get the number for their customer service. They stand behind their products and im sure they will help in every way they can to repair the drill

Nov 26, 2009 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

1 Answer

DeWalt cordless drill DW926. I can't get the


Turn your drill speed selector to "1" and put drill direction in reverse. Hold the outer end of the chuck and push the trigger. Should come loose.

Nov 18, 2009 | Dewalt Cordless drill/driver kit 9.6 volt...

2 Answers

Dewalt cordless DW995 , 18.0V broken piece in side.Can't open.


A TORX I believe , if it is a 6 point star type screw hole? They are measured in mm I think and 15 and 20 are the most common sizes.

Mar 26, 2009 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

1 Answer

Drill bit Stuck (and then broke off)!


b94710a.jpg078ca6c.jpg
Keyless chucks have two parts (see pictures) when the drill is in operation both parts spin. Assuming you put the drill bit in and tightened the keyless chuck by hand, put on a work glove and grasp the part of the chuck at the front of the drill, grasp the other part and twist the front part anti clockwise.
If this does not work you can hold the front of the chuck and reverse the direction of the motor as if you were unscrewing something, then pull the trigger. If your hand does not grasp the chuck tight enough it will slip, hence the glove. If this does not work you may have to hold the front of the chuck in a vice or with caliper pliers and again the pull the trigger with the drill in reverse.
All this depends on what you used to put the drill bit in with your hand tight or held onto it with something else. Whatever was used should be enough to loosen the chuck
Hope this helps.
If it does let fix ya know.
Cheers
Les

Feb 02, 2009 | Dewalt DW056 18 Volt Cordless Impact...

Not finding what you are looking for?
Dewalt 18 Volt Compact Drill Kit Logo

713 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills & Drill/Drivers Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Jim Thurston

Level 3 Expert

669 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Are you a Dewalt Drill and Drill/Driver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...