At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
The scanner will come on but sounds like sqealch is to high ,but it does not effect it at all,also when this happens a number is displayed it just want scane help me please jerry hill
Re: The scanner will come on but sounds like sqealch is...
Hi,my name is John. Try to adjust your squelch to where it will be silent, then press scan. hope this was helpful..Rate this solution on the four thumbs-up, good luck. John..
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
In spite of the display, does the effects work and do they change when you dial up and press the knob down? If they do, then likely the display is at fault. If the effects are NOT working sound wise, check the +5 volts as the whole effects runs from that, It should be within 10% of the 5 volts.
The backlight in your scanner is an 8volt bulb, but your scanner is 10 years old, and the exact replacement is no longer carried by radio Shack. You can, however, replace it with a 6volt 25ma bulb, Radio Shack catalog number 272-1140. Replacing it is fairly simple if you're at all handy with electronics and a soldering iron. Contact your local RS to purchase or order the bulb, and I'm certain that they can have it installed if you're not up to trying it yourself.
You didn't mention your location or the type(s) of digital system signals you lost, but if you've been listening to an EDACS system it's possible that the manager has switched on the PROVOICE security option. That would prevent your scanners from recognizing the effected users and would also account for both scanners being effected. If your area is using EDACS I suggest that you visit www.RadioReference.com to check on system particulars.
The PRO-95 is also known for losing its logic and requiring a RESET or INITIALIZE, although it would odd for two units to go squirrelly at the same time.
If all else fails, you can RESET or INITIALIZE the scanners to bring them back to normal operation.
To RESET: - Power the scanner OFF - Power the scanner back ON - Insert a pointed object (paper clip, penpoint, etc.) into the RESET hole on the back of the scanner - Gently press and then release the RESET button inside the hole.
NOTE: RESET will NOT erase the data that you've programmed into the scanner.
If RESET doesn't clear the problem, you can carry out the more drastic INITIALIZE process.
- Power the scanner OFF - Power the scanner back ON - Press 0 then 1 while "Welcome to Dual Trunking" is displayed. - "Initializing Please Wait" will appear for about 2 seconds.
DO
NOT power the scanner OFF until the INITIALIZE process is complete
(M000 and Bank 0 Ch 00 appear on the display). The INITIALIZE procedure
will reset the scanner to original factory settings and erase all data
that you have programmed.
This is a potential solution but if you are traveling down the highway and take your foot off the gas (or if you are on cruise no gas is required to maintain your speed) then the instant mpg calculation is similar to this 60 MPH / 0.0 GPH so effectively you end up with infinite gas mileage. But because the motor has to idle it's always using a little gas so it puts a very small number for the denominator which ends up giving you a high MPG. I've seen this happen in many makes of cars and I don't think it's anything to worry about.
When you downloaded the driver, did you make sure it was for the specific moder scanner that you have?
From the control pannel of your computer make sure that you added the cannon driver to the computer, you have to select
( ) cannon driver. I tmust be the spacific model name and number on your scanner.
The scanner must be on, so you can start test scanning . Why is not ON?
Finally after you done this avobe, If it doesn't work, the problem might be the cables.
Artgirl
hi,i have had the same problem but my son sorted it,go to control panel,sound effect manager,sound effect tab,my key read +4,this should be +0.it worked for me.
i dont know how it changed but it did,good luck
×