We would like to use our Wii to visualize multimedia files on TV from the computer without using a cable. We know that it's possible but a little bit difficult than Xbox and Playstation 3. Wii model:# RVL001 (USA) PC Window Vista Merci. Simon.

Hi Sane,

Multimedia Projectors uses a high power lamp to project the image onto a screen. These lamps have a typical life of 2000-3000 hours. It is quite possible that it may have blown.

1. Confirm that the unit itself switches on. You should have some sort of visual feedback from the projector that the unit is switched on, ie. the power light comes on, if it doesn't, check your power chord.
2. If there is power on the unit, but no image/light, check the unit for a fault indicator/light. Cross reference this with your user manual.
3. If you are unable to verify or do not have a user manual, "google search" your make, model and fault-code, else
4. approach a sales consultant at your nearest Audio & Visual retailer for advise.

My take is that the lamp has blown and needs replacement. These can be obtained from a Audio & Visual Retailer and can be self-installed with a little technical knowledge.

Everything You Need To Know About Replacement Projector And TV Lamps.

Here is what it looks like and what it typically costs:
multimedia projector lamp life Google Search

Did you hit the input button on your TV remove to select the input where the Wii is connected? If you TV allows for Component cables try getting a set of those. It's a possibility the TV connection has gone bad. Try connecting it on another tv. or some tv's have Audio connections in the front/Side/back.

Try to connect your Wii to another component input on the same TV, or to another TV. If the video works in one of those cases, then there is a problem with the TV. If not, your cable is likely broken. Try using a new component cable. If all this fails then there is a serious issue with your console that probably cannot be repaired at home.

Usually this is either a cable or a mode issue. First make sure that you have the correct cable connections. (Composite video cable to a component video jack is one possible cause of the problem.) Component video cables are not included with the set but will give better results. However, composite video in from the wii's composite video out should give good results.

If you are using HDMI or component video cables, then go into the Wii video menus to select the correct mode for your tv. Check your TV manual and the Wii setup guide for details on the mode (resolution, etc) you should be using.

If the problem persists, try new video cables and make sure that they are fully seated on both sides. Try switching inputs if you have several available.

I hope this helps.

Cindy Wells

HDMI cable for the Wii but a "Component" cable which is as near to HDMI as possible. The cable has 5 plugs on it (make sure your TV has the same 5 plugs). They are available off of ebay

u can download repair guide

click here to download repair guide

You need a tuner to tune in the tv channels. use a vcr that way you can change your channels

Are you selecting the right "Input" you do NOT use "Channels" You select an "External" input Or AV, "Audio Visual".

I just recently install Window 7 ultimate on my computer and then Acrobat 8 Pro start acting up. Try to open PDF file it will open for a little while then this thing pop up said Microsoft visual C++ Runtime Library and Runtime Error. Then it shut down.

Anyone know how to solve this problems please help.
Karoon Yip
[email protected]

Are you putting the cable into the correct audio and visual ports? check to make sure. Also, IF you have the little box that switches it from HD to analog tv is turned to the proper setting...if you have HD then make sure its on the HD. If you dont get any help on here you may check to see if you have any warranty on it and see where to take it to get it serviced.. hope it helps!

i put the wii on, powers up but i get a total black screen. wiimote does not connect either. what can i do to resolve this?
i have already disconnected all wires and connections, left it off for hours and tried putting it on again. no change. Black screen still remains. HELPPPP