Question about Milwaukee 1670 1 Drill 1/2 900 Hole Hawg

1 Answer

Need forward/reverse switch for older red and metal heavy duty 1/2 inch 7amp milwaukee drill serial number 0007196072.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 760 Answers

Link to find parts list:

http://www.milwaukeetool.com/CMS/Diagrams/54-10-4006.pdf

You can google the 23-66-1020 part number and find numerous suppliers.



RECALL NOTICE!

Milwaukee is providing a no-charge warranty service to owners of 1610-1, 1630-1 1/2" Compact Hole-Shooter Drills and

1670-1, 1675-1 1/2" Hole-Hawg® Drills. We are taking this action because under certain circumstances the switch of the drill

may stick in the "on" position, which could lessen control of the product, posing a risk of injury to the operator.

1610-1, 1630-1 1/2" Compact Hole-Shooter Drills and 1670-1, 1675-1 1/2" Hole-Hawg® Drills within the serial number

ranges shown below and sold between May 30,2000 and February 27, 2001 are affected.

Nameplate Catalog Number Serial Number Range

1610-1 700B400200013 thru 700B400480097

1630-1 718B400230057 thru 718B400480118

1670-1 472B400200061 thru 472B400440188

1675-1 413B400190567 thru 413B400522000

Drills listed should be inspected for the presence of a 23-66-1020 Switch with a date code within 0 0 2 1 t h r o u g h 0044.

If the unit contains a subject dated coded 23-66-1020 switch, please return drill to the nearest Milwaukee factory Service Center

or Authorized Service station for no-charge warranty replacement of the switch.

Affected switches carry a manufacture's four [4] digit date code of 0 0 2 1 t h r u 0044 imprinted on its body.

If nameplate has an 'X' stamped into the tool's nameplate, next to the catalog number, the tool has been repaired and the

defective switch has already been replaced.

If you need assistance in locating the service facility nearest you or have questions please call 1.800.729.3878

Posted on Oct 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vintage unlisted model Milwaukee drill with frozen chuck.


on the bench drill ( drill stand ) if you see a long slot in the shafts when you pull the drill down all the way , the you will need a tapered bit of metal that fits in that slot
Drive the metal through so that it forces the chuck assembly out of the morse taper
You can get replacement units from any good tool shop

Apr 01, 2018 | Milwaukee Drills

1 Answer

My impact driver when in reverse works fine but when in forward it will work for a few seconds then stop and keeps doing that. why?


I'd be looking for a defective forward/reverse switch, or a bad connection/wire on the forward side between the switch and the motor.

Jul 01, 2015 | Dewalt DW056 18V Heavy Duty 18V Cordless...

1 Answer

My cordless drill is running at half RPM. Is it the brushes or the motor?


cordless drills have a switch that allows for more torque at lower rpms si in effect it is a 2 speed drill coupled with a variable speed switch that alters the rpms
If the drill is running I would be looking at a speed control problem at this point I would be looking at the torque control switch

Jul 01, 2015 | Milwaukee Hand Trucks Milwaukee Electric...

2 Answers

MAGNET LIGHT BLINKS AND MOTOR WILL NOT TURN ON


Magnetic drills have a safety system built into them so the motor will not run unless the magnet is on and the tool is sitting on between at least 1/8-inch and 1/4-inch steel. If your drill is sitting on enough steel you may have a problem with the sensor system inside the drill. Those problems are usually electronic parts related and, most of the time, they are R&R (Remove & Replace) method is used until you fix the problem.

Jan 16, 2013 | Milwaukee Tool Milwaukee 4210-1 aka 4262-1...

2 Answers

Electric Milwaukee drill locked in reverse


This is a common issue with drills, you can resolve the issue by purchasing a new trigger switch and installing it. It is a very simple task. all you will need is a screwdriver and about 10 minutes.

Mar 09, 2011 | Milwaukee Electric Drill 1/2in. Chuck...

1 Answer

The chuck on my Dewalt 18v hammer drill will not stay tight. it loosens whether I am in forward or reverse


the chuck on my dewalt 18 volts hammer drill will not stay tight it loosenss whether i am in forward or reverse

Oct 14, 2010 | Dewalt DC920KA Heavy Duty Xrp 18V Cordless...

1 Answer

Milwaukee heavy duty hammer drill only works when pointed upwards. As soon as I point it down the motor stops (or doesn't start with the drill in that position).


could be loose connection at the switch or brush holders. You can go to Milwaukeetools.com to download a breakdown for this tool.

Aug 14, 2010 | Milwaukee Drills

1 Answer

Variable speed doesn't work on Milwaukee Magnum hammer drill


how new is the tool. Give me the serial number and I will come up with a solution, also what is the switch number you bought. Let me know.

Dec 31, 2009 | Milwaukee Drills

Not finding what you are looking for?
Milwaukee 1670 1 Drill 1/2 900 Hole Hawg Logo

378 people viewed this question

Ask a Question

Usually answered in minutes!

Top Milwaukee Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Jim Thurston

Level 3 Expert

672 Answers

Mike

Level 3 Expert

4350 Answers

Are you a Milwaukee Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...