Question about Homelite FactoryReconditioned ZR10522 46cc 20in Gas Chain Saw

1 Answer

This one is a new reconditioned saw. Sounds like a contradiction if ever.. I have maybe 10 minuites on it. Will start just fine, and run untill it get somewhat warm then starts running as if spark or fuel is being slowly eliminated. Then it will stall. Will have to wait untill it cools then it starts and does the same thing. It is under warrenty but if this is just a simple fix I would just as well do it myelf as to travel 75 miles to the nearest homelite service center. Have adjusted low and high because it did have a hesitation under throttle but it made no difference. I live 9000 feet high but do not think that that has anything to do with it. Thanks to all who respond. I have been an auto mechanic for 35 years so I will understand what you try to explain.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 7,733 Answers

Did you try a new "cooler sparkplug" And yes high altitude had something to do with the sattings.

Give a try on --->HomeLite Support.

Posted on Oct 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New to table saw use, have my husbands old 10 craftsman, was learning to rip with it doing fine, then it started to bog down during cut until the blades stops, moving. put on a new blade and noticed...


If I understood correctly, you started using your husband's table saw and while ripping boards, you managed to stall out the blade AND motor?! If that's the case, you probably have a very dull blade and are binding your board on the blade. Neither is safe and it sounds like trouble is brewing.

First and foremost, get someone to show you how to safely and properly use and adjust the saw if you are new to wood working and power tools. That saw is capable of turning your lumber into a high speed missal if you do things improperly.

It also sounds like you tried installing a new 10" saw blade. Changing the blade requires 2 wrenches. One to hold the arbor and one to tighten the nut. The blade itself should rest on the arbor between two large washers. Also make sure you install the blade so the front face of the cutter teeth face you and rotate toward you. Make sure the saw is unplugged when changing the blade and never turn on your saw with a loose blade.

Oct 20, 2013 | Craftsman 10" Table Saw

1 Answer

Its a new one not reconditioned but it didnt come with manual and i cant put it togather its a 4000-09


What's the problem they come mostly tougether? They are great saw's! A break down can be found at tools parts direct.com

Jun 25, 2010 | Bosch 4000 Factory Reconditioned 10"...

2 Answers

Husqvarna 359: Has run fine for 3 years. Now when first starting idles fine but as soon as it warms up idle speed increases enough to continually engage the clutch. Carb. setting have never been changed...


I think an air leak and she is running lean. Maybe time for some pressure/vacuum testing. Continuing to tweak the carburetor may camouflage a larger problem until the saw fails.

If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou

Apr 05, 2010 | Husqvarna Chain Saw 20" Bar

1 Answer

FR- 2.0 14'' Factory Reconditioned My


I am going to assume you are following the warm start procedure in your manual. Most start problems with 2-cycle engines are caused by flooding.

Before you shut if off roll it to the side and loosen the fuel cap (vent tank - leave it loose until restart) Better? Repair fuel vent. No better carburetor needs small adjustment. This explains it better than I can but you will need to experiment some.
Carburetor Adjustment by Madsens.com
http://www.madsens1.com/saw%20carb%20tune.htm
CW is leaner; to lean will destroy the saw. If over tightened closed (CW) the adjustment screw faces are easily marred; marred adjustments are difficult to impossible to set properly.
Clean the air filter; adjusting with a dirty filter can cause a run lean condition once cleaned and the saw run.

There are 2 wav (sound - idle & full – may not be highlighted) files that I find most helpful, I think you will too.

Just because this is the most likely cause:
Start Procedure
Cold:
  1. Ignition on/off to on
  2. Set compression release – optional step even if saw is equipped with a compression release
  3. Pull (close) choke, set fast idle (done when choke closed on some saws); pull starter and listen for an attempt to start. once heard (usually two pulls; no more than 4)
  4. Set compression release – optional step even if saw is equipped with a compression release
  5. Push (open) choke pull starter until it starts. (usually first pull)
Warm:
  1. Ignition on/off to on
  2. Set compression release – optional step even if saw is equipped with a compression release
  3. Pull (close) choke, set fast idle (done when choke closed on some saws) – Do not pull with choke closed.
  4. Push (open) choke, pull starter until it starts. (usually first pull)
I hope you found this helpful. You can reply below if you need additional help.
Lou

Jan 17, 2010 | McCulloch Garden

1 Answer

Replaced armature and brush's and there is alot of heat and spark and it starts slowing down?


Unless somewhat preformed, brushes have a tendency to arc like crazy and can produce heat and even smoke. I would remove the brushes and use a fine 'keyhole' type file to give them a little inside curve so they have better contact to start with.

Nov 02, 2009 | Dewalt DW744 Factory Reconditioned Heavy...

1 Answer

I am looking for a repair manual for my 10" ryobi


Takes a bit of navigating to reach it, but I'll try to help you get there.

Start at this page HERE.
Click "Repair Parts Catalogue"
Click "I HAVE READ THIS PAGE & AGREE TO THE TERMS PROVIDED".
Click the "Model" tab located at top left of page.
In the box labeled "Model Name/Number" type in the following without the brackets [TS1342] and click the "Search" button to the right.
One (1) Result should be found. To the right is a list of two available drawings.
The one you seek is "General Assembly"

Hope this helps,
Dolf-

Oct 15, 2009 | Ryobi ZRTS1342L Factory-Reconditioned 14...

Not finding what you are looking for?
Homelite FactoryReconditioned  ZR10522 46cc 20in Gas Chain Saw Logo

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Homelite Garden Experts

roeb

Level 3 Expert

603 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Mike Squire

Level 2 Expert

420 Answers

Are you a Homelite Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...