Question about Dishwashers

1 Answer

Dishwasher will not start and multiple lights are blinking including the lock button

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

It is very possible that the locking mechanisim has slipped past the actuating point. If you take the front of the dishwasher off you should be able to see all the componets and determine if something just slipped out of place.

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinking auto lock Whirlpool


What does it say in fine print right under control lock? "Press & Hold"? Page 16 of the user manual shows it as "air dry" with two lights, twelve and three o'clock positions. It says hold it for four seconds and the light turns off.

Aug 20, 2012 | Whirlpool GU1200XTLS Stainless Steel...

1 Answer

My Kitchenaid dishwasher is acting up. Everything else works but when you push the start button it will not start. model # KUDM01TJBT0


What happens when you try to start ?Do you get any lights blinking?Do your hear any motor turning ?What happens?

Sep 09, 2010 | KitchenAid 24 in. KUDI01IL - Multiple...

1 Answer

Normal cycle button blinking, cannot start new wash cycle


Press Heated Dry, Normal, Heated Dry, Normal buttons in sequence within 6 seconds to reset control. Could also be locked. Press and holding the air dry button for four seconds.

Nov 18, 2009 | KitchenAid 24 in. KUDI01IL - Multiple...

1 Answer

Kenmore dishwasher ultra was quiet guard 3 model 56516012403 control panel will not activate red lights blinking on normal wash and cancel drain. did the hold the heat dry button then the normal wash...


that would be model # 66516012403 correct??
you may have inadvertently set the lock on function..
check this out from your manual...

Lock On
Use the Lock On to prevent unintended use of the dishwasher
between cycles. You can also use the lock feature to prevent
unintended cycle or option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked. However, the lock must be turned off and the Start/
Resume button pressed to resume the cycle.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
NOTE: If the Heated Dry option is selected, the light will
temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.

hope this helps,
best of luck,
ttfn

Oct 25, 2009 | Kenmore 15912 Built-in Dishwasher

2 Answers

Lock Light Blinking


silly question but did you try holding the control lock button(perhaps its the heated dry button) in for 3 secs???? sonds as if the CONTROL LOCK has benn activated( child lockout)

Jan 14, 2009 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Dish washer 665.13824k601


LOCK LIGHT STAYS ON AND WILL NOT START. I HAVE TURNED THE POWER OF AT ELECTRICK PANEL AND IT STARTED ONE TIME. BUT DID NOT START ANYMORE.

HELP

Nov 27, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Kenmore elite dishwasher 665 15962990


Hold down the "HEATED DRY" button for 4 seconds to unlock.
Try to press these botton in sequence,Heated Wash, Heated Dry, Heated Wash, Heated Dry.release your hand, the unit will go into diagnostic mode. that is all leds will ON for a few seconds,and start normal operations.
If that does not work, you might need to check the electronic control board if the ribbon is seated properly.
Finally solution, is to change the electronic control board.

Jul 27, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Kitchenaid dishwasher mdl: kud101t jbt0


try the reset button sequence.. described in that other post about the clean light blinking.. that will reset the whole machine..

tpug

Jul 07, 2008 | KitchenAid 24 in. KUDI01FL - Multiple...

5 Answers

Kenmore dishwasher Lock On light flashing


holding the button for four seconds will not do it, you have to hold it until the light stops blinking and
will go back to normal, normall takes more than four seconds to unlock the unit, this is something
the sears repair techs know becouse the are trained on all this things but, they will not share this things, becouse thats how they make money

Dec 29, 2007 | Dishwashers

2 Answers

DISHWASHER LOCK


I too had the same problem,,and tried it again,,,and it worked for me,,i pushed the button next to the lock light it blinked and i kept holding in the dry button and the lock went off,,,,good luck

Aug 15, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...