Question about Sharp AR-BC260 Color Copier

1 Answer

Sharp arc 262 m

I have done what told me and its working perfectly,there is a maintenece massage code is DC,any idea what that is and how to fix it plz?
Regards

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 54 Answers

It means the drum for Cyan is due for replacement. Can reset with sim 24-7. Hit P * C * on control panel hit 24 then start (copy button) then select 7 enter. Select Cyan or C. Hit execute, then Yes. After complete hit CA button twice.

Don't forget to rate your answers please!

Posted on May 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have xerox dc 250 machine, it shows fault code 077-909, paper jam at tranfer module but i checked there is no paper in it??


Hello friend, you are not alone !!!!
From http://www.copytechnet.com/forums/xerox/28764-dc-250-fuser-problem-077-909-a.html

At the bottom of the page it says.......

'what sometimes happens is that the sensor flag/arm call it what you will, twists out of its holder and jams, hence the machine thinks that there is still paper. the flag/arm should pivot freely'

Sep 03, 2014 | upbright AC / DC Adapter For XEROX...

1 Answer

What is maintenance code of DC on Sharp 3100N


This is a scheduled maintenance programmed into all of these machines. It pops up when the machine crosses a certain "milage." If your machine is still making nice copies and prints it's nothing to worry about.


Copier Collin Houston TX Copier and Imaging Expert

Jul 04, 2014 | Sharp Printers & Copiers

1 Answer

What does error code dc on sharp 3100n mean?


image cartridge cyan need to be replaced

Jul 04, 2014 | SHARP MX-3100N

1 Answer

H4-00


There are 2 possible causes for this error - both closely related. H4-00 means the fusing temperature is not reached within a specified time. You can check and clean/replace the thermistors in the fuser unit, check the thermostat aswell. If thermostat rattles it is good otherwise press the reset button it. If everything checks ok reset the fuser code in service mode pressing the following keys :
P * C * then enter 14 and start then confirm action and restart copier. If error comes back then it could be related to the wiring harness to the PCU board (loose connector) or possibly a bad lamp. Check the lamps with a meter set to check continuity (you should get a beep if its working)

Mar 21, 2009 | Sharp AR-BC260 Color Copier

1 Answer

SHARP AR201 COPIER


Hey Robert,
Sounds like it could be in need of a maintenece kit. The ghostinf is usually caused from the fuser or transfer roller. And that would also apply to the band down the page.

Feb 13, 2009 | Sharp AR 201 Copier

1 Answer

OKI microline 3391 MATRIX PRINTER - WRITE IN CRO ČĆ?Đ????


It can't be done, that printer dont speak croatian.But thanks anyway

Nov 17, 2008 | OKI MICROLINE 3391 Matrix Printer

1 Answer

Sharp arc262


FK is Fuser Kit. You can check supply status by hitting P * C * then 22 start then 1 start. You can scroll down pages. Alot of the numbers displayed will make no sense to you, because they are values not meter counts.

Don't forget to rate your answers please.

Jun 04, 2008 | Sharp AR-BC260 Color Copier

1 Answer

Sharp arc 262


Turn off machine, open drawer where fuser unit is and gently pull out the jammed paper. You may have to replace the fuser unit.

May 27, 2008 | Sharp AR-BC260 Color Copier

1 Answer

Sharp arc 262


Open the Left side door and remove the fuser unit by unscrewing the large green wheel located under the frame on the left side door below the fuser unit. Lift the fuser unit using the handles front and rear sides. (be careful it is very hot). Set the fuser unit on a table or counter or desk. Look carefully at the left side, as it sits in the machine, near the middle. You should see a actuator for a sensor. Make sure both ends of the arm are in the holes where they shoud be. If it is out of place, put it back into place and carefully place the fuser unit back in the machine. Secure the fuser back in the left door and close the door.

May 27, 2008 | Sharp AR-BC260 Color Copier

2 Answers

No bottons are working


This means the developer unit is not installed . Check and instal.

May 16, 2008 | Sharp SF 2020 Copier

Not finding what you are looking for?
Sharp AR-BC260 Color Copier Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Printers & Copiers Experts

George Mclaughlin

Level 2 Expert

330 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Vito Suglio

Level 1 Expert

23 Answers

Are you a Sharp Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...