Any one know how can I configure forwarding so my emule will work

To emulate Amiga buttons on your X2 Plus Game Stick Retro Console, you can use an emulator like Amiberry or lr-puae . Here are the steps to emulate Amiga buttons on your X2 Plus Game Stick Retro Console using Amiberry:

Install Amiberry on your X2 Plus Game Stick Retro Console by following the official installation guide .

Download the WHDLoad packages for Amiga games you want to play .

Place the WHDLoad packages in /home/pi/RetroPie/roms/amiga/.
Configure your controller by following the official controller configuration guide .

Launch Amiberry and select the game you want to play .
If you prefer to use lr-puae, you can install it from the optional section of the RetroPie-Setup Script . Once installed, you can place your desired Kickstart ROMs in /home/pi/RetroPie/BIOS/ and use disk and WHDLoad games with this core .

Amiga - RetroPie Docs

TikTok - Make Your Day

Amiga Gotek: Getting started guide ' Installation ' Set up and Game downloads (FlashFloppy) - Retro32

This should help. Its the exact instructions you need to forward ports with emule and your Netgear WNR2000:

http://portforward.com/english/routers/port_forwarding/Netgear/WNR2000/eMule.htm

Yes this router has a port forwarding capability, to know about that and how it is done from this router check this link.
http://portforward.com/english/routers/port_forwarding/Dlink/DI-634M/DI-634Mindex.htm

i'm using no$gba2.6a. what i did is... i click the southeast map and minimize the emulator

Here is how to set up port forwarding for emule: http://portforward.com/english/routers/port_forwarding/Linksys/WRT160N/eMule.htm If you use emule Plus see here: http://portforward.com/english/routers/port_forwarding/Linksys/WRT160N/eMule_Plus.htm

Hi,
To make the change permanent, click Tools and select System commands,
on the system commands click save all.

Hello,

I recommend checking out http://portforward.com/english/routers/port_forwarding/Belkin/F5D7230-4/eMule.htm

This is a great tutorial on configuring port forwarding on your particular router. This example is for emule but it will be very similar to uTorrent. You will want to determine what port uTorrent is configured to send data on and use that accordingly.

Good luck!

Jacob

it sounds like to emule client is hogging all your bandwidth. Try and limiting your emule client to only use 70% of your total bandwidth. If you don't know your internet speed, then go to www.speedtest.com and run a test

DMZ is a feature that is included on some routers but is not in Internet sharing software. A DMZ allows a single computer on your LAN to expose ALL of its ports to the Internet. When doing this, the exposed computer is no longer ?behind? the firewall. Port Forwarding vs DMZ A DMZ is far easier to set up than port forwarding but exposes your entire computer to the Internet. Sometimes TCP/IP applications require very specialized IP configurations that are difficult to set up or are not supported by your router. In this case, placing your computer in the DMZ is the only way to get the application working. Placing a computer in the DMZ should be considered ?temporary? because your firewall is no longer able to provide any security to it.

You must open ports on your router to allow incoming traffic while using eMule. eMule uses three ports*: 4662 (TCP) 4672 (UDP) 4711 (TCP) Visit eMule here. * To prevent getting a low ID (Firewalled), open additional TCP ports between 4661 and 4665. Also, limit the number of connections in the eMule software. You may need to change the TCP Clientport to something other than 4662.