Question about RCA HD52W56 52" Rear Projection HDTV

1 Answer

Set turned off game back on in 3D

Our HDTV R2WM2 Which is little over a year old, and never moved and not use much.Turned off, and game back on , almost looking as the images are in old fifties 3D movies. Almost a fish-eyes or curved effect. Colors look lime green yellow and blue and pinks in and in a triple like out line. Like I said like a 3d movie or comic

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 317 Answers

Have convergency rebilt

Posted on Jun 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a Mitsubishi WS 55313 rear proj TV. Has been used maybe 30 hours in all. TV sat for a few years unused. Passed TV to my daughter. Once TV was reconnected at her house, she watched it in all its...


All old DLP tvs have a common design flaw,any time this could happen during the tv existing life,the tv problems is call a convergence problems,it dead.Tv have colors lines R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?The tv convergence board is dead,the board have dead 2 STK convergence ICS and some or all of it resistors too.This parts on the tv convergence board,must me replaced,to solved the tv picture convergence problems.The shop,will cost u like $300-350 for parts and labors.

Dec 13, 2010 | Mitsubishi WS-48313 48" Rear Projection...

1 Answer

Intermittent problem of no picture


Archive Projection TV Repair Answered Questions QUESTION NO. P710-9: Sony KP-53XBR45 projection TV picture had severe intermittent vertical pincushion symptoms. Pincushion problem stopped and picture now ...

No thank you, Not interested in buying another TV at this time But the above solution should give ya some ideas in what to look for and could help ya and get your tv back on again.

Good Luck, Please dont for get to Vote.Thank you

Dec 14, 2007 | Samsung HLN5065W 50" Rear Projection...

1 Answer

Rca 56 inch, picture looks like its in 3D


Go to menu then setup if you do not see convergence in menu then FL231 is bad it is on right side of FBT flyback Transfomer on the deflection board their is 3 of them in a roll small brown rectrangler looking caps but are fuses it will be the one in the Middle if fuse is good try this with set off Press and Hold at same time vol- and ch- see if set will come on this is How to Enter service Mode.

Aug 26, 2009 | RCA R56WH76 Projection Television

1 Answer

Phillips HDTV looks like it is in 3D


Your convergence ic's went bad and possibly took out the fuses in that circuit. I believe they are stk392-120's on that set. Also, check all the resistors around them. Should be located on two heatsinks near front of chassis. Good luck.

May 19, 2009 | Philips 50PP9202 50" Rear Projection...

1 Answer

DLP HDTV shut off, sound but no picture


replace light bulb,
if you are hearing a click like the stove is because the lamp balast is trying to power on the lamp,
if you need part number and vendor please send me the model number

Apr 18, 2009 | Philips Magnavox 50ML8105D 50" HDTV DLP TV

5 Answers

Phillips rear projection tv model #60pp9202/17f


Here are some of the most common symptoms and example photos of a convergence problem

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
701cb04.jpg
77ea520.jpg
f0900cb.jpg
Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.



You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

2c07611.pngSolution #1

You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick note and they will put one together for you. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, etc.

Feb 25, 2008 | Philips 60PP9202 60" Rear Projection...

1 Answer

Samsung HLN5065W Light Engine problem or not?


Look at my ether post on cleaning out the DMD bord I thank this will fix your problem.

Dec 16, 2007 | Samsung HLN5065W 50" Rear Projection...

2 Answers

AKAI 55" Rear Projection TV won't turn on.


the 3d effect tells me that your convergence ic's have blowned. standard for these sets.. not to much of a difficult repair. repair them all the time..

Dec 13, 2007 | Akai PT5598HD 55" Rear Projection...

1 Answer

Projection 52" lcd


so use the warranty as is less than a yr old let them fix it....

Aug 09, 2007 | Hitachi 60V500 60" Rear Projection...

1 Answer

Horizontal Lines


The unit most likely has a short in the horizontal section and would require repair by a service center. Go here to find a JVC repair center in your area http://maps.jvc.com/cAscList/

Sep 18, 2006 | JVC AV-56WP74 56" Rear Projection...

Not finding what you are looking for?
RCA HD52W56 52" Rear Projection HDTV Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...