Question about Honeywell Heating & Cooling

2 Answers

My Honeywell rth230b thermostat continues to give me a flashing snowflake signal and will not allow the AC to turn on.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 49 Answers

Your snowflake should flash for about five minutes, that is the time delay built into the thermostat. It should stop after that and your system should begin to function.

Posted on May 29, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

    Sergeant:

    An expert that has over 500 points.

  • Master
  • 347 Answers

The snow flake indicator is a feature of the unit. I doubt it is not functioning. Just let it blink for a few minutes then you should be able to use the unit. If you need any more advice checkout AC Repair Fort Lauderdale

Posted on Mar 03, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honeywell portable heater HCE322V manual


Honeywell has the manual for the HCE322V ceramic tower heater on the product page: http://www.honeywellstore.com/store/products/digital-ceramic-tower-heater-hce322v.htm . Click on the Manuals tab. The direct link to the manual is http://www.honeywellstore.com/store/images/pdf/HCE311-HCE322-HCE323-honeywell-heater-manual.pdf .

I hope this helps. Note: the manual covers a few different models. You should ignore any section about the HCE323; that model has a remote and a few other extras.

Cindy Wells

Jan 08, 2017 | Honeywell Heating & Cooling

2 Answers

Replaced ac unit with new compressor. Fires up as usual but compressor wont start.No fault code coming on controller. Whats the problem?


possible causes include
excessive gas
low gas
relay not working,
faulty thermostat
faulty start/run capacitor
bad circuit board

Jan 03, 2017 | Heating & Cooling

2 Answers

What icon do i use on my handset to cool a room


Hello Glen Turner,

Snowflake (?)

Just guessing here
(a brand, make & model would've been really helpful)

Carnac the Magnificent

Jan 01, 2017 | Heating & Cooling

1 Answer

I need to know if a mercury thermostat is bad will it allow the ac to come on but not the heater


need to know what thermostat you are referring to
the coolant thermostat has no connection to the ac system
if it is the ac thermostat the it maintains the cabin temperature by activating the ac compressor as required
if you are referring to climate control then that controls the heater flow to keep the ac temperature at a set temperature with the ac compressor operating all the time
so as an answer to you question , check the climate control module

Dec 30, 2016 | Heating & Cooling

2 Answers

My thermostat is set on 68 degrees and it shows room temperature is 68, but the furnace still kickson, Honeywell said it has a 1 degree difference. so what's the problem then?


Yes there is a one degree tolerance, in fact my heater just kicked on and it is set to 67 and the inside temperature reads 67. It is also a Honeywell.

Dec 28, 2016 | Heating & Cooling

1 Answer

Electric Furnace stopped running


You have one of two problems. Either the capacitor for the motor has failed or the motor has failed. I would turn off the power to the unit and see if you can locate the capacitor and remove it. An ac supply or electrical supply house can match up the capacitor. This is relatively inexpensive. Otherwise you will need a new motor.

Nov 11, 2014 | Heating & Cooling

1 Answer

Ac will not turn on. Once I pull the face it will work but if I try to turn to another setting it turns off again. Help


Hi Aaron,
You need a new thermostat, they are not very expensive and they are easy to install...

Oct 24, 2014 | Heating & Cooling

1 Answer

My termost set to a/c, the fan auto, blow very well, but when I switch to heat and the fan auto, doesn't work, but if I put fan on work why?


the thermostat says to call for heat buildup in the work if its not cold enough the thermostat won't call for heat and I won't go on but when it gets cold and the thermostat set to the temperature you want or hire someone that doesn't cycle

Oct 12, 2014 | Heating & Cooling

1 Answer

Why can't I lower my honeywell 8500 below 67 on cool?


With a two story house you have to be aware that cold air flows downwards so any cold air coming from an ac unit will flow downstairs( normally down the stairway) so unless you can close off the down stairs then the up stairs unit will be cooling downstairs as well. Ac units have a thermostat located in the air intake and it cools until the cold air has risen to that point. In effect the space above the ac unit will be hotter than the floor. Knowing how they work ,you can see that the upstairs unit will never reach the set temperature because the cold air is continually heating from the house and will never get to the top thermostat.
So your solutions are
1-- fit controls that restrict the cold air from leaving the upper floor (Doors)
2--don't run the upper ac unit unless you are living up there (waste of money
)3 place an ac in each upper room and keep the room door closed

Aug 12, 2014 | Heating & Cooling

2 Answers

Flashing re co


Re Co stands for Recovery Mode. That means if you have programed your thermostat to be at say 72° at 5:00 then it should kick on in Recovery Mode several minutes before 5 in order to reach that temperature. This is normal and doesn't indicate that something is wrong, just that your thermostat is trying to reach or recover the programed temperature.

Feb 08, 2008 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

7,848 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honeywell Heating & Cooling Experts

Bill Long

Level 3 Expert

587 Answers

paulcarew

Level 3 Expert

2047 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Honeywell Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...