Question about Blenders

2 Answers

Cuisinart bc56 blender

How do i change the clutch on this blender i have brought a new clutch but can't get the old one off!help I need to replace the clutch on the blender and I don't know how to remove the old one and replace with new one.

Posted by on

  • Anonymous Oct 19, 2008

    I am usually quite handy with any widgets and gadgetts but this one is a real pain in the patunski and I will probably never buy another Queezy art product again! I cannot, for the life of me, get the old driver clutch off of the working end of the motor shaft and need to do this first, before I can even begin to install the new one.The motor will not come out of the blender housing until the clutch is removed and there is no apparent set screw on the actual clutch driver plate itself. There is only a flat head screw located at the other end of the motor shaft which acts as if it was welded into place! Please help, if someone out there in magic box land has the answer, I'd sure appreciate hearing it. Thanks! wwmarkush

  • Anonymous Jan 19, 2009

    How do you remove the clutch - there are so many websites selling the clutches - but with no instructions on how to replace them! It madness!

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Instructions found in operations manual. "The rubber clutch disc on the blender base has reverse threads. To replace , remove the rubberclutch disc by threading it clockwise. To install the new clutch disc, thread it onto the motor
shaft counterclockwise."

Posted on May 19, 2009

Huh?

Posted on Jun 07, 2008


1 Suggested Answer

  • 1 Answer

SOURCE: cuisinart bc56 blender

I cannot find the part of the rotator that goes on the blender. the cuisinart parts only have the one that goes into the jar

Posted on May 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove old blade?


Hi Paul,
There is a collar on the base of the jar that screws onto the jar. You will need to unscrew the collar and fit a replacement blade. make sure the seal is replaced with the blade and the collar is screwed back securely.
See this link for the parts of the blender.
CUISINART CANADA SmartPower Premier 600 Watt Blender CBT 500C
Also see the product description for the blade.
https://www.youtube.com/watch?v=rdBxUAsT_TQ

Mar 04, 2015 | Cuisinart Replacement Cbt-Bg-1 Blender...

1 Answer

Manual is destroyed. Need new copy for Cuisinart PowerBlend Blender/Food Processor


The Instruction Booklet for your Cuisinart BFP-703 SmartPower Work Top Blender can be found here:

http://www.cuisinart.ca/pdf/ibs/en/BFP-703CHC_en.pdf

Thank you for using FixYa!

Jul 30, 2011 | Cuisinart BFP-703 SmartPower Work Top...

3 Answers

My cuisinart spb-7 blender won't spin


How do I replace the blender blade driver clutch? I have the part but do not know how to get it in.

Jun 13, 2009 | Cuisinart SPB-7 SmartPower Work Top...

2 Answers

Clutch on the jar of my cbt500 cuisinart blender is broken.


The clutch assembly is for the teeth on the base itself. If your problem is with the teeth that are connected to the bottom of the blade that sits in the jar, you want to order a blade assembly instead.

-Tha Mp3 Doctor (also loves Cuisinart)

Mar 21, 2009 | Cuisinart Blenders

1 Answer

Cusinert blender


I had the same problem and I manaed to fix my Cuisinart SmartPower Duet blender. There are two thermal fuses, one tape attached to each stator winding. Both of mine were blown.

In addition, when the fuses blew, it must have spiked the triac. I had to replace mine. It's the black 3-legged transistor looking device with a small metal heatsink attached to it. This gizmo directly throttles the power to the motor under control of the microprocessor. There are some guides on the internet on how to test it.

Also, the clutch was very hard to remove and needs to be removed to more easily replace the thermal fuses. I clamped down the end of the motor shaft to a bench vise real hard and then I used a 7/8-inch open-end wrench to wedge into the clutch prongs which made it much easier to apply torque. Remember that its screw threads are reversed from normal screws so that it does not unscrew during operation. You have to turn it counter-clockwise to unthread it.

Hope that helps!

-Vince

Sep 13, 2008 | Cuisinart SPB-7 SmartPower Work Top...

2 Answers

How do I change to clutch on this blender. The outside of the clutch broke off leaving just the screw head on the blender, when I turn to unscrew it, the entire piece just spins, any suggestions.


You can probably use a Vise-grip pliers to clamp down on the brass insert and unscrew it. Not only is it on very hard, but it is also threaded reverse of a normal screw. This is so it does not come undone in normal operation.

You have to turn it counter-clockwise to unscrew it (a regular screw turns clockwise).

I had to clamp the motor shaft real tight with a bench vise to be able to remove the clutch. Hope this helps.

-Vince

Aug 14, 2008 | Cuisinart SPB-7 SmartPower Work Top...

2 Answers

Cuisinart bc56 blender


how to get the base off the glass container. turn in what directionss it seems stuck

Feb 27, 2008 | Cuisinart CBT-500 SmartPower Premier Work...

4 Answers

Lights blink, but Cuisinart Smartpower 7-speed wont turn.


The thermal fuse is blown. You can buy a replacement from RadioShack for $1.69 You have to remove the old one and solder in the new one. If youre "handy" its very easy. Take it to a repair shop, you pay about the same as a new one. Its too bad that most electronics made today are cheaper to throw away and buy a new one rather than fix them when they break.

Aug 14, 2007 | Cuisinart SPB-7 SmartPower Work Top...

2 Answers

Broken gear on BFP-703 base


The drive is replacable and available from Cuisinart, you will have to sign a waver to get the part. the drive is screwed onto the motor shaft with reverse threads. the plastic drive will have to be completely broken off of the unit to expose a brass"nut" which was internal to the drive. depending upon your model you may have to remove the lower half of the base unit to access the lower part of the motor shaft. there will be a slot in the end of the shaft for a large flat blade screwdriver. this is used to hold the shaft still while turning the drive "nut" with a vice grip pliar or similar. the new drive is just threaded onto the shaft and normal operation tightens it.

Feb 14, 2007 | Cuisinart BFP-703 Blender

Not finding what you are looking for?
Blenders Logo

Related Topics:

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blenders Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

eyecam

Level 2 Expert

86 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...