Question about Miele T1302 Electric Dryer

1 Answer

It takes 3 cylcles to dry clothes - Miele T1302 Electric Dryer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Miele Master
  • 7,482 Answers

If your dryer seems to run forever, it could be because of a clogged vent or internal ductwork. Your dryer may have an automatic cycle that turns off the dryer when the clothes are dry. It does this with a special thermostat or moisture-sensing system.
Normally, this is what happens during an automatic cycle:
The thermostat tells the dryer to heat until the interior of the dryer reaches a pre-set temperature--say 135 degrees.
When the dryer reaches the pre-set temperature, the thermostat tells the timer to begin advancing. (If there's a moisture sensor, the timer advances only if the moisture content of the clothing is low enough.)
The timer advances until the interior cools, then the thermostat tells the timer to stop advancing, and tells the dryer to start heating again.
This cycle continues until the clothes are dry. But...if the vent is clogged, the dryer may never reach the proper operating temperature, so it doesn't send the signal to the timer and the dryer continues to run indefinitely, even if the clothes are completely dry. To fix the problem, clean the vent and/or internal ductwork.
Heating Element
Your dryer's heating element may be partially burned out. If it is, your dryer still heats, but at such a low temperature that it takes three or four times as long to dry the clothes. If the element is partially burned out, replace the heating element. You can check for an ohm reading but will need to refer to the service manual for proper reading. This sometimes on the tech sheet located somewhere on the dryer. Usually between 9-13 ohms.
Cycling thermostat
Although this isn't a common problem, one of the thermostats that controls the temperature in your dryer may break and cause the dryer to heat poorly. If so, you need to replace it. The thermostat is usually a small, round, black device mounted to an oblong steel plate. The plate is mounted to the internal ductwork . This thermostat usually has four wires going to it. Check the 2 terminals that are opposite each other and are the closer together of the 2. These 2 terminals should have continuity. If not replace the thermostat.
This is a free answer, Please rate me

Posted on Oct 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my washing machine not complete a rinse & spin cylcle?


is it a top loader? if so, older top loaders do not have a balancing function so you must evenly distribute the load.

Oct 16, 2016 | Washing Machines

1 Answer

Taking to long to dry clothes


How long does it take you to dry your clothes? Normally, it takes 50 minutes (1 cycle) to 1.5 hours to completely dry clothes. However, if it's taking you at least 3 cycles (probably 2.5 to 3 hours) to dry a single batch of clothes, then, there might be a problem with your dryer's igniter.

Jan 09, 2014 | Speed Queen AGS17AWF Gas Dryer

1 Answer

I have a GE washer/dryer Model WSM2700RAWWH stack type and the dryer is taking very long time to dry the clothes. Please advise if it can be fixed. If not what will be best alternate washer/dryer stack...


first things first. if any dryer regardless of brand takes 2-3 hours to dry cloths 90% of the time it is your exhaust duct. take the exhaust duct off the back of the dryer and dry some clothes if the clothes dry fast then you need to have your exhaust duct cleaned. either DIY or call a professional
if it still takes a long time to dry then it could be the thermostats or the thermistor.
but in my experience its normally the exhaust duct.

Feb 10, 2011 | GE Washing Machines

1 Answer

Dryer is not drying clothes very well


check your wall vent,if it is clogged it will not dry right-mike

Jan 24, 2010 | General Electric DHDSR46EGWW Dryer

2 Answers

Dryer heats up but doesn't dry clothes take 3 hours after restarting 3 times to dry 3 articles of clothing.


It's not your heating element. Your venting system is clogged. Like mine was. You'll need to take care of this ASAP and from then on at least once a year. It is a fire hazard. Not only that if left this way It can kill your heating element.


9_12_2012_9_40_31_pm.jpg

Oct 15, 2009 | Whirlpool LER4634J Electric Dryer

3 Answers

Our dryer does not completely dry cloths even with small loads they have to be run 2 or 3 cylcles but there seems to be plenty of heat.


maks sure exhaust is fully flowing. plenty of air also filters are clear no fluff...good luck

Sep 29, 2009 | Dryers

1 Answer

LG dryer (model DLE3733W) takes forever to dry the clothes.


check your vent hose for a clog. If dryer dont vent clothes wont dry.

Aug 25, 2009 | LG DLE3733 Electric Dryer

1 Answer

Dryer heats up but does not dry clothes


first take the venting off the back of the dryer and dry a load if dryes normal replace venting if takes a long time to dry have a repair man clean the dryer

Jun 12, 2008 | Kenmore 74602 Gas Dryer

1 Answer

Spin cylce is slower than it should be


Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too. Height of exit hose should be approx 3 feet from ground level.

Rate me pl.....if helped.

Jan 02, 2008 | Kenmore 44832 Front Load Washer

Not finding what you are looking for?
Miele T1302 Electric Dryer Logo

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Dryers Experts

Tim Whalen

Level 3 Expert

3074 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Miele Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...