Wireless-G WPS54GU2 Print Server Lost disk

HP LaserJet 1022 is a "host-based" printer so it must be connected to a PC. Load the driver on PC first and connect the USB cable when software tells you to do so.

Will not work on a Linksys print server.

LaserJet 1022N & LaserJet 1022NW have "special" HP print servers that can support HP host based printers.

Hi,

Based on your post description, I am assuming that:
1. You can connect to the Internet through your 2241 Neptoia modem;
2. You can access your WRT54G V8 Linksys Wireless router @ 192.168.1.1;
3. Both 1 & 2 above could be done through a wireless connection from your PC.

Connect everything as they are supposed to be wired (printer, Print Server, modem, router etc)

Pls try:
a. Connect the Linksys wireless print server using a lan cable to the Linksys WRT54G Wireless AP/router. (Will tackle the wireless connection a bit later)
b. Reset your print server; &
c. Do a diagnostic print-out.
Instructions for b & c are in page 4 of your manual.

You need to verify that:
i. the Power indicator is contnously green
ii. the Ethernet indicator is contnously green
iii. the USB indicator is contnously green
iv. the Wireless indicator may or may not be contnously green

Pls post back with the generated diagnostic print-out before we can proceed with the other steps.

Additionally, try installing the Epson Stylus Photo RX600 direct to one of the USB ports of your PC. Use the installer/driver CD that came with it. Try using it as a regular printer. This will tell us status of the printer.

Good luck and kind regards.

I'm not sure how you have your server set up, but when I did the initial setup I had to add my printer as a TCP/IP port.
See this link for instructions on how to do that: http://homecommunity.cisco.com/t5/Print-Servers/Installation-of-WPS54G-Print-Server-for-Windows-7/m-p/362651?comm_cc=HSus&comm_lang=en#M6440
The hanging on the last page happens if you don't have LPR byte counting enabled. Go find your printer in the devices and right click. Go to "Printer Properties", then the ports tab. Click "Configure Port", then in the popup dialogue make sure that LPR Byte Counting Enabled is checked.

If you are using a belkin router, wrt54g-tm and netgear switch box. Basically they won share the printing. you need a wireless print server..try the linksys WPS54GU2

Check the settings on your wireless print server. And as well check your router.

Installation of WPS54G Print Server

Using standard TCP/IP Procedure (Windows XP/2000)

1. Make sure your printer already has its drivers installed on all PC's prior to attempting to install this print server.
2. Be sure also that your printer can print when it is connected directly to your computer.
3. Click on Start go to Printers and Faxes.
4. Right click your printer and go to Properties.
5. Click on the Ports Tab on the top.
6. Click Add Port. Select Create a new port: and select the Type of port: Standard TCP/IP Port, click Next.
7. This will bring the Add Standard TCP/IP Printer Port Wizard, click Next
8. Inthe field for Printer Name or IP Address: enter the IP address of thePrint Server and click Next. (You can get the IP address of your printserver by pressing the reset button on your device for 3 seconds thenit will print out it's status).
9. Select Custom, click Settings.
10. Under Protocol select LPR, and for Queue Name: type L1. Click Ok, then Next, and Finish.

Youshould be able to print on the device afterwards. You can refer to yourRouter's Wireless Settings and match them on the WPS54G so that theywould be able to communicate wirelessly.

1. For re-configuration of the printserver, it has to be wired to the router.
2. You may go to this site http://www.linksys.com/servlet/Satellite?c=L_CASupport_C2&childpagename=US%2FLayout&cid=1166859942287&pagename=Linksys%2FCommon%2FVisitorWrapper&displaypage=nodata#versiondetail to download the setup wizard.

great if ur laptops r acessing the internet ... perform the followings ....
> open the page of the print server and try to match the wireless settings of the router on it and u will be able to use the printer as well ....

Reset the Wireless print server , and run the setup cd once and check..press the hold the reset button for 60 sec with the power cable connected , that would properly reset your print server and then try to install it..contact linksys support for live assistance over phone 1800-546-5797

generally speaking any compatable wifi unit should work with any other unit.. In saying that yes it is "Better" to get all the same make if one can.. but not essential.