Question about DISH Network IR Remote Control

1 Answer

DWIN tv, Marantz receiver and Dish system. Three different remotes needed to control. One for On/Off of the tv, one for the volume and the third for the Dish network. What is the best way to get to one remote? Most cost effective remote?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

Youdo have the ability to program your current DISH Network remote to all of yourcomponents. If you decide you would like to do so, I have included instructionsto assist you in programming your remote. In order to program your remote toyour DWIN television without the remote code, (I'm sorry unfortunately I wasunable to locate a remote code for a DWIN Tv L) you can complete what we refer to asa "Power Scan," to do this you would complete the following steps. 1. Withthe desired equipment on, press and hold the correct Mode button until all modebutton backlights illuminate, then release. (In this case the mode button willbe "TV") 2. Pressand release the Power button. 3. Pressthe Up button once a second while pointing the remote at the desired equipment. Note: If the code for the equipment comes up, theequipment will power off. 4. Pressthe POUND (#) button. If the codeentered is valid for the remote, the mode light flashes three times.

-In addition, you can also program the remote to yourMarantz receiver this can be done by pressing and holding the AUX botton inupper left corner of remote next to the SAT button.
-Press & hold AUX until all the other mode buttonslight up, then release AUX button, all the other mode buttons should turn off,only AUX button should be blinking now,
-While AUX button is blinking enter in the remote code742 for the Marantz receiver and then press the # key (pound key.) Afterpressing the # key on your remote, the AUX mode button should blink 3 timesmeaning the programming has been completed successfully. While still in AUXmode try any function on the remote, such as turning the volume up or down onyour Marantz receiver. The DISH Network remote should now be programmed tocontrol the receiver.
-If the 742 code doesn't program the DISH Network remotesuccessfully you can also try each of the following using the same procedures, 743,651, or 740. After completing the power scan to program the DISHNetwork remote to your DWIN t.v, & completing the AUX mode buttonprogramming, the remote should now work for your TV to powere on and off, theMarantz amplifier- to control the volume, and the DISH Network receiver. Hopethis helps! -Kirstie DISH Network

Posted on Jan 30, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The number 2 remote control do not work the remote


ramoshummer,

I would need more information to provide you a specific resolution, but below I have included basic steps to programming your remote to both your TV and your DISH Network receiver.

Link for codes if needed: http://www.dishnetwork.com/SupportSection/remote-setup

Addressing Remote to TV:

1.) Press and hold the clear TV button until all mode lights light up.
2.) Release and TV light will be blinking.
3.) Enter code and press #. The TV button should flash 3 times.
4.) Try functions (Volume, Power, etc..) and see if working.
5.) If no function, repeat steps 1-4 with another code.

Addressing Remote to Receiver:

1.) Go to System Info screen.
2.) Hold down the SAT button until all mode lights light up.
3.) Enter a number between 1 and 15 using the numeric keypad on the remote.
4.) Press the pound (#) button.
5.) Once the SAT button blinks three times, press record.
6.) Test remote and see if works.

If those don't solve your problem or you're experiencing a different issue let me know here or at thomas.faust@dishnetwork.com and I will check it out!

Tommy Faust
DISH Network

Sep 08, 2011 | DISH Network IR Remote Control

Tip

DISH VIP612 Program AUX Remote Code 2


DISH Solo DVR VIP612 Program AUX Remote Code

7c06801.jpg

Would you like to program the Universal Remote that came with your Dish Solo DVR VIP 612 to control your receiver, tuner, stereo, second TV or second VCR using your remote's AUX mode? (Instructions to setup a primary TV or a VCR are a little different, but can be found here.)

e818a57.jpg

To setup your Dish Solo DVR VIP 612 Universal Remote, follow these steps to enter the remote control codes to control a device with the AUX mode:

  1. Turn the device you would like to control on.
  2. Find the brand name of the device you would like to control in the control code tables on page 112 of the Dish Solo DVR VIP 612 User Manual.
  3. Press and hold the AUX mode button until all the other buttons light up, and then let go. The AUX mode button will flash.
  4. Press 0 for a TV, 1 for a VCR, or 2 for a receiver, amplifier or tuner.
  5. Enter one of the three-digit codes from the tables in the manual.
  6. Press POUND (#). The mode button will flash three times.
  7. Press POWER to turn off the device. If the device does not turn off, skip to step 9.
  8. Turn the device back on and try some of the other buttons to make sure they work. If the code works, stop here.
  9. If the code didn't work, repeat steps 3 through 7 with the next device code from the tables in the manual.
Your device control codes for your amplifier or other AUX device are now programmed into your DISH Solo DVR ViP 612.

Now you probably want to set your Dish Solo DVR VIP 612 Universal Remote up so that it always controls the volume of your stereo, rather than of your TV, regardless of whether it is in SAT, TV, VCR or AUX mode. Help for this remote control programming can be found here.

(Help for programming a TV or VCR using the TV or VCR mode buttons can be found here.)

I hope that helps.
________________________________________________________________
DISH Solo DVR VIP612 Manual Download
DISH Solo DVR VIP612 Quick Reference Download
DISH Solo DVR VIP612 Remote Code Scan
DISH Solo DVR VIP612 Program TV VCR Remote Codes
DISH Solo DVR VIP612 Program AUX (Stereo/Receiver) Remote Codes
DISH Solo DVR VIP612 Amplifier Control
DISH Solo DVR VIP612 What Is Limited Mode
DISH Solo DVR VIP612 Change Limited Mode

on Jul 05, 2010 | Televison & Video

Tip

DISH VIP612 Amplifier Control


DISH Solo DVR VIP612 Amplifier / Receiver Control

7c06801.jpg

Would you like to program the Universal Remote that came with your Dish Solo DVR VIP 612 to control the volume of your receiver, tuner, or stereo instead of your TV's volume?

e818a57.jpg


The first step in using the Universal Remote Control that came with your Dish Solo DVR VIP 612 to control the volume level of your receiver, tuner, or stereo is to program the remote to control your audio device using the AUX mode button.

Once your remote controls your audio device in AUX mode, you probably want to continue to control the volume of your stereo even if the remote is in SAT, TV or VCR mode.

To setup your Dish Solo DVR VIP 612 Universal Remote to control the volume of your stereo regardless of which mode it is in, follow these steps:

  1. Press and hold the AUX button until all the mode buttons are lit, and then let it go.
  2. Press the POUND (#) button.
  3. Press the PLUS side of the VOLUME button.
  4. Press 0.
  5. Press the POUND (#) button. The AUX button flashes three times to tell you the programming is complete.
  6. Confirm the VOLUME buttons are operating the tuner/amplifier's volume control by pressing SAT or TV, and then adjusting the volume. Your tuner/amplifier's volume should change rather than your TV's volume.

Your Dish Solo DVR VIP 612 Universal Remote is now setup to control the volume of your stereo regardless of which mode it is in

I hope that helps.
________________________________________________________________
DISH Solo DVR VIP612 Manual Download
DISH Solo DVR VIP612 Quick Reference Download
DISH Solo DVR VIP612 Remote Code Scan
DISH Solo DVR VIP612 Program TV VCR Remote Codes
DISH Solo DVR VIP612 Program AUX (Stereo/Receiver) Remote Codes
DISH Solo DVR VIP612 Amplifier Control
DISH Solo DVR VIP612 What Is Limited Mode
DISH Solo DVR VIP612 Change Limited Mode

on Jul 05, 2010 | Televison & Video

1 Answer

I have a Dish IR. Not sure of the model number. Uses 4 AAA batts. The problem I have is the every function seems to work fine except for the volume control. In order to change volume I have to use the TV...


It is possible that those buttons have failed, but a bit more likely the remote lost the codes for the TV itself... since almost everything the remote controls... is on the DVR. I apologize if I am guessing wrong in assuming other "TV" buttons (like INPUT) don't function either.

To re-program your remote to recognize your TV (like when the tech first set up the system) choose from the following receiver types to find the correct remote control TV codes for your Zenith.

Remote TV Codes for 722/622/612/411/222/211 Receivers
Remote TV Codes for 625/522/512/510/508/501 Receivers
Remote TV Codes for 811/381/322/311/301 Receivers

Aug 29, 2011 | DISH Network IR Remote Control

1 Answer

Cannot program Dish IR remote l03602


adeline_roll

You didn't specify if you are trying to program the remote to your TV or receiver. Is it a replacement remote or did it just quit working? I have provided instructions on how to program to your TV or receiver.

Address to receiver:
Remote: All Other Remotes
  1. Go to System Info screen (depending on receiver - press System Info button on receiver panel or pull smart card out till System Info screen appears on TV screen).
  2. Hold down the SAT button until all mode lights light up.
  3. Enter a number between 1 and 15 using the numeric keypad on the remote.
  4. Press the pound (#) button.
  5. Once the SAT button blinks three times, press record. Note: If successful, the number selected in step 3 will appear in the System Info screen under Remote Address.
Remote: Basic Remote (Television Only)
  1. Turn the Television On.
  2. Press and hold the TV Power button for three seconds until the LED flashes.
  3. Press and release the TV Power button.
  4. Press and release the Up or Down Arrow on the remote until the television turns off.
  5. After the television turns off, press and release the OK button.
  6. Test functionality with the TV.
  7. Return to Step 2 if the remote is not able to turn the TV On/Off, change the volume and mute the television.
Please let me know if you have any other questions or problems. Thanks.

Ray Calo
DISH Internet Response Team

Jun 23, 2011 | DISH Network IR Remote Control

Tip

DISH VIP612 Amplifier Control


DISH Solo DVR VIP612 Amplifier / Receiver Control

7c06801.jpg

Would you like to program the Universal Remote that came with your Dish Solo DVR VIP 612 to control the volume of your receiver, tuner, or stereo instead of your TV's volume?

e818a57.jpg


The first step in using the Universal Remote Control that came with your Dish Solo DVR VIP 612 to control the volume level of your receiver, tuner, or stereo is to program the remote to control your audio device using the AUX mode button.

Once your remote controls your audio device in AUX mode, you probably want to continue to control the volume of your stereo even if the remote is in SAT, TV or VCR mode.

To setup your Dish Solo DVR VIP 612 Universal Remote to control the volume of your stereo regardless of which mode it is in, follow these steps:

  1. Press and hold the AUX button until all the mode buttons are lit, and then let it go.
  2. Press the POUND (#) button.
  3. Press the PLUS side of the VOLUME button.
  4. Press 0.
  5. Press the POUND (#) button. The AUX button flashes three times to tell you the programming is complete.
  6. Confirm the VOLUME buttons are operating the tuner/amplifier's volume control by pressing SAT or TV, and then adjusting the volume. Your tuner/amplifier's volume should change rather than your TV's volume.

Your Dish Solo DVR VIP 612 Universal Remote is now setup to control the volume of your stereo regardless of which mode it is in

I hope that helps.
________________________________________________________________
DISH Solo DVR VIP612 Manual Download
DISH Solo DVR VIP612 Quick Reference Download
DISH Solo DVR VIP612 Remote Code Scan
DISH Solo DVR VIP612 Program TV VCR Remote Codes
DISH Solo DVR VIP612 Program AUX (Stereo/Receiver) Remote Codes
DISH Solo DVR VIP612 Amplifier Control
DISH Solo DVR VIP612 What Is Limited Mode
DISH Solo DVR VIP612 Change Limited Mode

on Jul 05, 2010 | DISH Network ViP 612

Tip

DISH VIP612 Program AUX Remote Code


DISH Solo DVR VIP612 Program AUX Remote Code

7c06801.jpg

Would you like to program the Universal Remote that came with your Dish Solo DVR VIP 612 to control your receiver, tuner, stereo, second TV or second VCR using your remote's AUX mode? (Instructions to setup a primary TV or a VCR are a little different, but can be found here.)

e818a57.jpg

To setup your Dish Solo DVR VIP 612 Universal Remote, follow these steps to enter the remote control codes to control a device with the AUX mode:

  1. Turn the device you would like to control on.
  2. Find the brand name of the device you would like to control in the control code tables on page 112 of the Dish Solo DVR VIP 612 User Manual.
  3. Press and hold the AUX mode button until all the other buttons light up, and then let go. The AUX mode button will flash.
  4. Press 0 for a TV, 1 for a VCR, or 2 for a receiver, amplifier or tuner.
  5. Enter one of the three-digit codes from the tables in the manual.
  6. Press POUND (#). The mode button will flash three times.
  7. Press POWER to turn off the device. If the device does not turn off, skip to step 9.
  8. Turn the device back on and try some of the other buttons to make sure they work. If the code works, stop here.
  9. If the code didn't work, repeat steps 3 through 7 with the next device code from the tables in the manual.
Your device control codes for your amplifier or other AUX device are now programmed into your DISH Solo DVR ViP 612.

Now you probably want to set your Dish Solo DVR VIP 612 Universal Remote up so that it always controls the volume of your stereo, rather than of your TV, regardless of whether it is in SAT, TV, VCR or AUX mode. Help for this remote control programming can be found here.

(Help for programming a TV or VCR using the TV or VCR mode buttons can be found here.)

I hope that helps.
________________________________________________________________
DISH Solo DVR VIP612 Manual Download
DISH Solo DVR VIP612 Quick Reference Download
DISH Solo DVR VIP612 Remote Code Scan
DISH Solo DVR VIP612 Program TV VCR Remote Codes
DISH Solo DVR VIP612 Program AUX (Stereo/Receiver) Remote Codes
DISH Solo DVR VIP612 Amplifier Control
DISH Solo DVR VIP612 What Is Limited Mode
DISH Solo DVR VIP612 Change Limited Mode

on Jul 05, 2010 | DISH Network ViP 612

1 Answer

My remote is fully deprogrammed, how I can turn to turn on and off the TV and box


Hi, Cheri Torres with DISH Network Customer Service here. In order to help you reprogram your DISH network remote to your TV to control your TV functions such as power on/off of TV and volume, I would need the model number of the remote and the brand name of your TV. You should be able to locate the model number of your remote on the back of the remote at the top usually a 2 to 3 digit number with a decimal point. I will list here for you the instructions for reprogramming your remote to your DISH receiver to control your receiver functions. If you would also like me to help you get your DISH remote reprogrammed to your TV please email me directly at Cheri.Torres@Dishnetwork.com with your remote model number and the brand name of the TV. I hope you find this information useful and if you have any further questions or concerns feel free to email me.

Instructions for addressing the remote to your receiver.
  1. Go to System Info screen.You can do this by either pressing the system info button on the front of the receiver or you can press the power button once and then the channel up button once on the front of the receiver.
  2. Hold down the SAT button until all mode lights light up.
  3. Enter a number between 1 and 15 using the numeric keypad on the remote.Change the number to something different then what is already listed in the small white square.
  4. Press the pound (#) button.
  5. Once the SAT button blinks three times, press record. Note: If successful, the number selected in step 3 will appear in the System Info screen under Remote Address.

Apr 19, 2011 | DISH Network IR Remote Control

1 Answer

I need the remote control code numbers for the SR-18 so I can turn it on with my Direct TV remote.Do you know what they are?


the best thing to do is a code search per the directv manual and hope the Marantz powers off when you find the code.

If it turns off, you have won half the battle. Save the code and try turning the Mar back on.
The issue is that these universal satellite remotes are very limited on there funtionality with audio systems.

Keep in mind that if you find a code that turns it on & off, you will probably be limited volume only. If you get those three functions, you are very happy and call it done.

Hope this helps.

This goes for all sounds systems and not only Marantz.

Jan 19, 2010 | Marantz SR-18EX Receiver

1 Answer

After programming my NEW Harmony One Logitech remote I can't get it to change channels on the Dish HDTV DVR along with a bunch of other problems.


To control a Dish Network PVR/Satellite, it needs to be set to respond to the default Remote Address (1).

To reset your Dish Network PVR/Satellite to the default Remote Address:

1. Press SYSTEM INFO on the receiver's front panel. The System Information screen displays on the nearby TV and shows the Remote Address.
2. Using the original Dish Network remote, press and hold SAT on your remote control for about three seconds, until all of the mode buttons light up, and then release SAT.
3. Using the NUMBER PAD, press the 1 button
4. Press POUND (#). If you entered the address correctly, SAT will flash three times.
5. Press RECORD. Make sure the Remote Address you see on the System Information screen is 1.
6. Press the SELECT button on the front panel to close the System Information screen.
7. Your Harmony remote should now control your Dish Network PVR/Satellite box

NOTE: Dish Network PVR/Satellite receivers sometimes have two tuners, allowing them to be used in more than one room on different TVs. Harmony remotes can only control a Dish Network receiver's main tuner while still in the same room with direct line of sight to the device.


What other issues are you having with the remote?

Dec 25, 2009 | Logitech Harmony One Advanced Universal...

Not finding what you are looking for?
DISH Network IR Remote Control Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Televison & Video Experts

S. Gontko

Level 2 Expert

142 Answers

john milligan

Level 3 Expert

514 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a DISH Network Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...