Question about Vacuums

1 Answer

My McCulloch whipper snipper was working just fine after finding cracked fuel lines,. Replaced wiht home made lines and worked fine until Sunday and now wont start at all . Checked everything , now think its electrical Would like to kow if there is anyone in Perth who can sort this out

Posted by on

  • 3 more comments 
  • sabona Oct 04, 2010

    If they can get parts assuming its electrical then I will be extremely satisfied. I suspect its the equivalant to a coil that may have burnt out as there is no spark. Finding one for this model one may have to try the USA

  • sabona Oct 04, 2010

    I`ll see how I go with the lawn mower repair guy - if I can find one in Wangara - never had to use one except to replace blades :-))

  • sabona Oct 05, 2010

    Hopefully there is someone in Perth who can sort out the electrical side . I think the CDI coil has had it as there is no spark at all. If you know where in Perth I can take it would be most appreciative. Many thanks I had to roder to the cutting head from Randys Engine Repairs in Ohio and he is all but useless as he hasnt responded to any of my follow up post. Will lodge a compalint wiht E-Bay if Ihavent heard anything back by Friday

  • sabona Oct 05, 2010

    I wish I knew where in Perth I could get the CDI ignition coil replaced as there is no spark at all. I ordered the cutting head from Randys Engine Repairs in Ohio, and to date have not heard anyhing from him at all despite my follow up request. Will give him until Friday then hand it over to Ebay to sort out. If you know where in Perth I can take this to to get it sorted out would be most grateful. Many thanks. Peter

  • sabona Oct 06, 2010

    Thanks , I`ll try all of them and see what happens

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Vacuums Master
  • 32,281 Answers

Your local lawn mower repair shop will be able to fix it for you.

Posted on Oct 04, 2010

  • Chris Hingee
    Chris Hingee Oct 05, 2010

    McCulloch is a well known brand, I don't think you will having any trouble getting it repaired or obtaining spare parts.

  • Chris Hingee
    Chris Hingee Oct 06, 2010

    Here are some Australian WEB sites who can supply McCulloch parts. http://www.rotarymower.com.au/ http://www.au.best-price.com/search/land... parts/s/google/altk/Home Smart/

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont turn on after belt was replaced


Reset button is on the back towards the bottom.

Mar 20, 2014 | Riccar 8850 Vacuum

1 Answer

Vax turboforce not picking up


Hello Guest, Please check that your brushbar is turning, if isn't then your belt has broken, once replaced your machine should be fine.
If you need further help or advice, please call the Vax Customer Careline on 0844 412 8455 with your machine available, and an Advisor will be able to help you. The Vax Careline is open every day, from 8.30am until 6.30pm, Monday to Friday, and 9am until 5pm on Saturday and Sunday. Outside of these times please check the website support section which includes videos to demonstrate how to deal with everyday problems such as changing filters and belts and checking for blockages. With best wishes, The Vax Team.

May 11, 2010 | Vacuums

1 Answer

I need the fuel/gas mixture for a small (12") McCulloch Chain Saw. It has a 2.0 C.I.D. label with Fuel Mix I lnoted at the fuel cap. ja


The 2.0 CID is Cubic Inch Displacement, the size of your motor. As for fuel mixture, generally a 50:1 is a benchmark for this. Typically, it should be 1 gal. of gas for 2.56 oz. of two stroke oil. They sell pre-packaged, pre-measured oil at your local DIY shop or lawn mower repair shop.

Jan 18, 2010 | McCulloch MC1275 Steam Vacuum

1 Answer

I have a McCulloch Model PM 310 , Gas Chainsaw. How would the spark plug be accessed?....Rich


Storing a chain saw for longer than 30 days requires storage maintenance. Unless the storage instructions are followed, fuel remaining in the carburetor will evaporate, leaving gum-like deposits. This could lead to difficult starting and result in costly repairs. Never store a chain saw for longer than 30 days without performing the following procedures:
Remove the fuel tank cap slowly to release any pressure in tank. Carefullydrain the fuel tank.Start the engine and let it run until the unit stops to remove fuel from carburetor. Allow the engine to cool (approximately 5 minutes).
Using a spark plug wrench, remove the spark plug.
Pour 1 teaspoon of clean 2-cycle oil into the combustion chamber. Pull starter rope slowly several times to coat internal components. Replace spark plug.
Store the unit in a dry place and away from possible sources of ignition such as a furnace, gas hot water heater, gas dryer,etc. When removing the unit from storage, be sure to perform the following procedures:Remove spark plug. Pull starter rope briskly to clear excess oil from combustion chamber.Clean and gap spark plug or install a new spark plug with proper gap.Prepare unit for operation.Fill fuel tank with proper fuel/oil mixture.

This will help. Thanks, please keep updated. please do rate the solution positively .thank you for using fixya

Dec 15, 2009 | McCulloch MC1275 Steam Vacuum

2 Answers

I fill the hot water tank and it and it pours out of the tank onto the floor less than a year old used to work fine


don-I too have the same issue. I tore mine apart today and still don't know what the issue is...I have a Hoover Dual V...I'll let you know once I find the solution. Like you, mine machine is just at a year old.

Nov 15, 2009 | Hoover F7425-900 SteamVac V2 Widepath...

7 Answers

Parts for Mcculloch MC 1275 steam cleaner


You can find your parts on amazon. take a look here Amazon com Mcculloch MC 1275 parts. I hope this was helpful. cheers

Nov 15, 2008 | McCulloch MC1275 Steam Vacuum

2 Answers

Mc Culloch chain saw


You will need a parts breakdown and exploded views to start with as well as a manual , All you have to do is call 1-800-521-8559 and select U.S. then select the parts department, have your model number ready and ask them for a PDF of the owners user manual to be emailed to you, they will normally be sent in 1 hour for free.

After that is done then you can see the fuel filter and line inside the tank you will need to replace, take your printed views and manual to the nearby lawn mower shop and they will help you get the parts you need even if the original ones are not available. blow out the carb with chemtool and install the parts, use NEW GAS, NEW OIL and from that day forward never leave fuel in a unit for more than 3 months. Good Luck...

Aug 18, 2008 | McCulloch MC1275 Steam Vacuum

6 Answers

McCulloch Chain Saw Manual


Found all the mcculloch manuals you could ever want on mcculloch product information site. Its run by mcculloch an you put the product weather chainsaw or strimmer whatever an the type in the next collum an press download then print it off all very easy. My manual was in german so made up i found stumbled on this.

Jan 14, 2008 | McCulloch MC1275 Steam Vacuum

2 Answers

Problem hose


Try gently feeding a thin, springy wire down the tube to find is there is a blockage further up.

Mar 22, 2007 | Hoover F7425-900 SteamVac V2 Widepath...

Not finding what you are looking for?
Vacuums Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...