Question about Hotpoint VBXR1090B Top Load Washer

1 Answer

Vbxr1090b0ww hotpoint washer

I have a draining problem with my machine. A pillow got stuck during the spin cycle and it ripped it open and now all the stuffing is clogging the machine. We got a lot out and we checked the drain hose and it is clear. I need to know where and how to check I guess under the tub to clear out more stuffing. It now spins since we cleaned it more. But it will not drain. Please help I have a family of five and lots and lots of laundry.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 46 Answers

There is a large hose that runs from the basin to the pump. I would recommend checking this hose from the pump to the basin.  It is probably plugged in there as well as in the pump inpellor.  look under the machine to find the pump.. White/clearish plastic with 2 large hoses running to it

Posted on May 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WF220 Hotpoint - burning smell + wash cycle stalls?


The burning smell is coming from motor. Also your clutch is bad where you are hearing the rattle/grinding.

Dec 12, 2009 | Hotpoint Aquarius WF220 Front Load Washer

1 Answer

Door stuck


try unplugging and plug back in to reset

Nov 17, 2009 | Hotpoint First Edition FEW12 Front Load...

1 Answer

My BWD 129 washer dryer is not spinning or draining


I have a similar problem - washer wouldn't spin or drain. The problem with my Kenmore 90 series is that the lid switch needs to be replaced. It's a safety feature. During normal operation when the washer is spinning or draining - and you open the lid - the lid switch sensor knows that the lid is opened and then "stops" the machine. A new lid switch needs to be installed. I have picked up the part, but am still trying to figure out "how" to get inside of the washer. The only difference between what you describe, and my problem, is that there is no "unusual" noise coming from the machine. Hope this helps lead you in a good direction. Another good site is Bob Villa's site.

Jan 15, 2009 | Hotpoint Aquarius WD640 Front Load...

2 Answers

WMA54 Hotpoint Aquarius drum does not turn during wash or spin


Start checking the lid switch, if this is stuck the machine wont start.

If the drum does not move at all, the motor, the motor control unit, the motor coupler, the control board may be faulty.

For more details you need to observe if machine is draining and pumping water inside during cycle, see: It doesn't spin


Jan 06, 2009 | Hotpoint WMA54 Front Load Washer

1 Answer

GE WCSR2080B4WW - After wash cycle the washer does not spin and..


your washer must drain to spin.you may have a blocked or failed pump.you get to it thru the frount.use a putty knife between the lid and the frount ,push the springs.top comes up take frount off.pump has two hose .pumps white or tan smaller.God bless,tom

Jan 01, 2009 | GE WSM2700W Unitized Spacemaker Washer and...

1 Answer

Hotpoint WD420 Washer/Dryer - Not completing cycle


I WOULD FIRST CHECK THE COLD WATER VALVES ONE COULD BE INTERMITTEN

Jun 25, 2008 | Hotpoint Aquarius WD63 Front Load...

1 Answer

GE Top Loader - Spin Cycle Problem


bad door switch, probably ripped out by a comforter or pillow

May 29, 2008 | GE WBSR3140DW Top Load Washer

3 Answers

1 beep per second and odd light sequence


there some simple solutions but may not always work but everyone should try. underneath when the water pump engage with the tub. there;s a white plastic clip press it out and turn the water pump. it will come off the tub. before doing this you should have the washer disconnected. have someone or put something under so the washer won;t fell on you while reaching down. sometimes debris gets stucks on the way from the tub to the pump. it insert your fingers inside once the pump is taken out and if you find debris take it out. put back the pump and connect the washer again. this can be a very simple solution it won;t work all the times. but what if it does. :)

Jun 14, 2007 | Fisher and Paykel GWL11 Top Load Washer

Not finding what you are looking for?
Hotpoint VBXR1090B Top Load Washer Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...