Question about Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

How do you keep it from pulling strings on towels?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 905 Answers

Check the agitator for a nick, as well as check under the rim of the agitator (use a mirror) for foreign objects.

If you find a nick / abberation in the agitator, try sanding it smooth again with a couple different grits of sandpaper.

If there is a foreign object under the agitator that is grabbing the towels, you may have to remove the agitator to get to it (usually single nut at top).

Posted on Oct 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a 1989 big bear it pulls to the right i put new tie rid ends and upper and lower balk joints in pulled cv axel it seems to be ok steering bearings seem fine also anyine have any ideas


Try aiming the handle bar straight and pull some kite string across the rear wheel , lightly touching the sidewalls of the tire. With the length of the string pulled across the front tire, adjust the outer tie rod so as to make front tire lightly touch the string. That should square the front tire to the back tire. Once the front and rear are squared, adjust tie rod in 1 turn for a slight negative toe. Do both sides while making sure to keep the handle bar straight during string and adjustment. That should help.

May 25, 2017 | Cars & Trucks

1 Answer

Jessie doll string in the pulled position


Sometimes you can get the string cord to release and retract back. Hold the doll firmly and gently pull the string out about an extra two or three millimetres (eighth of an inch) or as much as possible. Keep the string tight for a short while and then allow it to retract slowly. It may take a few attempts, the skill is in pulling the string that little extra distance, holding it for a few moments, then slowly releasing it again.

Dec 30, 2013 | Toys

1 Answer

Cant get the buzz out of the high E string on my Epiphone les paul guitar


A buzz on one string is not due to a pickup fault. It's rather a too low string height at the nut or a string slot that is either too wide or has too deep of an angle towards the tuner. It could however be that you had the pickup too close to the high E string creating excessive string pull.

Jul 04, 2012 | Epiphone Les Paul Studio Electric Guitar

1 Answer

I don't remember how to start my weed eater;i've lost my manual


Hello,
Pump the gas bubble near the black box air filter. Start pulling the string. Keep pulling until it turns.
Thanks

Jun 03, 2011 | Ryobi 30cc 17" String Trimmer Zrry30530...

1 Answer

I am re-stringing my Fender 140sce and every time I begin to tune a new string up, the peg pops up. Do I keep pressure on it to try and keep it in place until it is fully in tune, or is this out of the...


It is a little tricky, but you have to kind of pre-form the ball end of the string so it tucks under the ledge of the hole it goes into. Then put peg in and as you do pull up on the string slightly so the pre-formed ball end is caught under the ledge. Make sure the slot is toward the neck direction and the string seats in it, Also once the string is seated, kind of preform the string over the edge of the hole as the string is started to be tightened.

May 28, 2011 | Fender CD140sce Acoustic Electric Guitar

1 Answer

Homelite Mighty Lite 26CS Model21004D


Once you have the string wound onto the spool, place the spool onto the shaft and pull the strings out of the slots so that the string feeds through the holes without going through the slots. Good luck...Lee

Jul 26, 2010 | Homelite Mighty Lite Lawn Trimmer

1 Answer

Had to replace E string on Baby Z. Having difficulty getting the string on guitar to wind Any assistance would be great!


Normally you leave string slack enough at the start so you can get 3 or 4 winds before it is at tension.

While winding, pull string sideways to keep gentle tension on the string.

They have cranks to speed up the winding process you caanbuy that are inexpensive.

Here is an excellent video of how to:

http://www.ehow.com/video_4396928_replace-strings-acoustic-guitar.html

Dec 28, 2009 | Dean Guitars Dean Baby Z Electric Guitar...

1 Answer

When I dry my towels in our dryers, they have started coming out with the "loops" of the material in strings. I then have to cut the strings off the towels.They almost look shredded. There is nothing in...


If it is a Kenmore or Whirlpool, the rollers are worn out. If it is a GE, could be the glides are worn out Both of these can be replaced.

Jul 14, 2009 | Dryers

1 Answer

What size strings? and how to adjust pickups and bridge adjustments. can i find an owners manual online?


String gauge is a personal preference. I'll ask you this: what is your playing style? I see your picture and its a Jackson DK2M. One thing to remember is that the Floyd Rose usually needs adjusted with a different string gauge. With a Floyd, I recommend replacing one string at a time unless you are cleaning the neck with steel wool. If you are taking all the strings off at once and changing them all at once and not one after another, put a towel under the back end of the Floyd Rose so it does not tilt back and mar the finish. Jackson usually installs 9's on their guitars, but this is too light in my opinion.

The pickups...there is a screw on each end of the pickup to adjust the pickups up and down. Raiseing them will get you more output but more noise and feedback. Lowering them will get you a more mellow sound. I keep mine no less than 3/16 to 1/8" from the strings.

Bridge adjustment...Floyd Rose trems are tricky little animals. They have small allen screws to raise the saddles up and down. Raise the bridge just enough to keep the strings from buzzing excessively and as long as they don't make a buzzing sound thru you amp, its nothing to worry about.

Send me a message if you have any more questions. With a Floyd Rose, it would not hurt to go consult your favorite guitar shop or a friend with a Floyd equipt guitar to see them work on them.

Apr 05, 2009 | Jackson Dk2m Dinky Electric Guitar

Not finding what you are looking for?
Whirlpool Calypso GVW9959K Top Load Washer Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...