Question about Siemens D1675 Motherboard

1 Answer

D1675 Boot problems

Ok the parts list, P4 2.8ghz 512cache 800 mhz cpu, 1675 mobo, 512/ 333mhz ram, western 80g hd, generic dvd drive, !micro/ atxp4 2,03 swicthing powersupply, generic atx case, windows xp pro with service pac 3. ati radeon 2400 pro 8x 256mb video card. Can't get this thing to boot comes to the win xp screen the little blue thing that scrols back and forth but the blue dot never comes up and then it cycles. win did not start properly blah blah blah. have tried 5 different video cards and the only time it booted all the way to the desktop was when we put in a card out of an old dell horizontal desktop i have no idea what it was. we had to take the bracket off the front to get it to go in but it worked. any body got a clue? I'm thinking the 8x card dosen't like the 1.5v bus???maybe the old dell card was a 4x??? each of the components have been tested in my other computers and appear to work properly when substituted. help, please.

Posted by on

  • ghoompah May 30, 2008

    Ok so following that logic 4 out of the 5, 8X agp cards are not backwards compatible. I guess I now need to know where to find a 1,5 volt Agp card. My next assumption would be that the bus or slot was bad but it works consistaltly with the card that is phsyically inapropriate mounting wise but ok pin wise.

  • ghoompah May 31, 2008

    My nvidia card is a three volt 256meg 8x with two key slots. My ATI card only has one slot but no voltage information 256 meg 8x. My PNY card also has one slot and no voltage information 256 meg 8x. The mother board we know has one key and my spec sheet says it's a 1.5v bus. I don't have access to the old dell card cause it belongs to a friend and he wasn't willing to give it up. I might be able to get him to pull it again so we can see. To tell you the truth I'm currently looking for another MB cause I know my parts are good they just don't like each other. I do want to thank you for your help though. I not quiting yet but I'm definitely looking at plan B.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,351 Answers

Hi ghoompah, It's easy to tell if an AGP card supports 1.5volt. Look at the contacts (Copper) key of the video card. There should only be two key connectors. (This does not include the locking tail).
If there are three connectors than the card is most likely 3.3volt.
Click the link included to get an idea of what to look for.
Many 8x speed cards are backward compatible with a 4x speed AGP. Other than looking at the video card it's self it's best to look at the AGP slot on the board. Count the sperations in the AGP slot. (Also known as keys).

Hope you find this helpfull!

Posted on May 27, 2008

  • 1 more comment 
  • Mike Peluso
    Mike Peluso May 30, 2008

    The Fujitsu Siemens D1675 features the SIS 648FX chipset with integrated audio, Ethernet LAN controller, Firewire and SPDIF. The D1675 is a Socket 478 ATX motherboard supporting Intel Pentium 4 processors with an 800 MHz Front Side Bus and Intel Celeron processors with a 400 MHz Front Side Bus. Expansion is handeled by the AGP slot, five PCI slots and the CNR slot.

  • Mike Peluso
    Mike Peluso May 31, 2008

    Why not make it a bit easy on me. Look into the AGP slot & tell me how many seperator's you find & how many copper connectors on the old dell card. (You're thinking what's a seperator)? Look at Intel's decription at this link.

    What you are learning is there are many cards, 2x, 4x & 8x AGP cards that will fit an AGP slot with two seperatores in the slot on the board even if there are three connectors on the AGP video card. This next link may help you understand things a little better.

    When you mentioned old dell I thought you had an old AGP card which would still fit an AGP 2x & 4x slot. Which is why I added the link from tiger direct. Supporting AGP 2X & 4X 1.5v graphics card.

  • Mike Peluso
    Mike Peluso May 31, 2008

    Well if you have any more questions feel free to ask. Just click the Ask Me button under my ID.

    If the information helped you at all I'd appreciate a green vote. Have a great wekkend!




1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

This is going to be a bit long winded so please bear with me\ System mobo: nforce 5m-a gpu gforce 7200 psu generic 450w cpu amd 64x2 4200 Ram generic 1gb onboard sound Ok I hit the power...

This sounds like an OS issue. Like some component is corrupted. I would try to boot in to safe mode and see what happens. If it works in safe mode than i would say it is some kinda software or driver issue. Might even be antivirus software. If you cant boot in to safe mode, have you tired to reload windows. If this is not possible because pc wont run long enough in safe mode or allow to start system reinstall i would remove all components like cd/dvd rom. just unplug the power and ide/sata cable. Re-seat Hard Drive cable(power and connection) remove all external devices like usb keyboard and mouse, printer and what ever else you have. I would also try to remove cmos battery for 1 minute just to reset it. Hope this helps.

Nov 06, 2010 | Computers & Internet

1 Answer

After power on my eMachines C6537, there is no beep sound and nothing shown on screen. The CPU fan and fan in the box are working. The HD drive spin sounds normal. No problem to open doors of DVD and CD...

Disconnect the power cable open the case and pull the CR 2032 battery out for a minute. That will reset the BIOS. If you have no Beep Codes at all the MoBo might be dead. If this were just a video issue there'd be Beep codes. If there's more than one stick of RAM Pull one try to boot then do same with second stick. if there's only one stick of RAM try reseating it.

Jun 27, 2017 | eMachines C6537 PC Desktop

1 Answer

Need specifications for Intel PM-865G1 mobo

• Supports Intel® P4 Northwood/Prescott/P4 Extreme Edition processors.(PCB v1.1 only)
• FSB 400(Northwood only)/533/800MHz
• Supports up 3.2GHz and higher speed
Memory Speed/CPU FSB Support Matrix
Memory Speed/CPU FSB Support Matrix

FSB\Memory clock DDR266 DDR333 DDR400 800 MHz YES YES* YES 533 MHz YES YES NO 400 MHz YES NO NO
• Intel® 865G Chipset
- Supports 800/533/400MHz Intel NetBurst micro-architecture bus.
- Integrated graphic controller.
- Supports PC2100/PC2700 /PC3200 memory.
- Supports AGP 8X/4X at 0.8V (AGP 3.0) or 4X at 1.5V (not support 3.3V) interface.
• Intel® ICH5 Chipset
- AC'97 2.3 interface
- 8 USB 2.0/1.1 ports
- 2 channel Ultra ATA/100 Bus Master IDE controller
- SMBus 2.0 support
- 2 serial ATA Host Controllers
- Integrated LAN controller
• Support 100(Northwood only)/133/200MHz
• Support 400(Northwood only)/533/800MHz Intel NetBurst micro-architecture bus.
• Supports two 64-bit wide DDR data channels.
• Available bandwidth up to 3.2GB/s(DDR 400) for single-channel
mode and 6.4GB/s(DDR 400) for dual-channel mode.
• Supports four unbuffered DIMM of 2.5 Volt DDR SDRAM.
• Supports up to 4GB memory size without ECC.
• One AGP slot supports 8x/4x at 0.8V (AGP 3.0) or 4x at 1.5V (3.3V is not supported).
• Three PCI 2.2 32-bit Master PCI Bus slots.
- Supports 3.3v/5v PCI bus Interface.
• One CNR slot
• Dual Ultra DMA 66/100 IDE controllers integrated in ICH5
- Supports PIO, Bus Master operation modes.
- Can connect up to four Ultra ATA drives.
• Serial ATA/150 controller integrated in ICH5
- Up to 150MB/sec transfer speeds.
- Can connect up to two Serial ATA drives.
• AC'97 link controller integrated in ICH5
• 6 channels software audio codec C-Media 9739A
- Compliance with AC97 v2.2 Spec.
- Meet PC2001 audio performance requirement.
- Can support SPDIF Out via 3-pin SPDIF bracket only.
• Intel 82562EZ
- Integrated 10/100 Ethernet MAC and PHY in one chip
- Supports 10Mb/s and 100Mb/s auto-negotiation operation
- Compliant with PCI v2.2, and LAN on Motherboard (LOM) standard

Apr 27, 2010 | Intel Motherboard

1 Answer

HD booting in one PC but not in another

Ubuntu works with RAM and CPU Memory instead of a pc like xp that uses Virtual RAM. If the pc that could not load ubuntu doesn't have enough ram to support the reading of the Hard drive and the Operating System then it won't work and Xp will only run on the computer that xp was installed onto the hard drive.

Dec 19, 2009 | Computers & Internet

1 Answer

New build pc no boot... black screen

Try to remove the battery from the MB, and next time you try to install WIN XP, when you are asked how to format your drive, chose quick NTFS formatting; disable floppy drive in BIOS, because it might try to boot from it (and I suppose you don't have one), and in boot sequence (BOOT DEVICE PRIORITY) set cd-dvd as first, and HDD as second, and turn off any other device as bootable

Nov 17, 2009 | ASUS M2N-MX Motherboard

1 Answer

Installed more ram and now can't find the hard drive

Pull out the new RAM chips and install the old one or ones and see if it boots ok. I had this same problem. This can also be caused by no using matched sets of RAM chips. In my case I added one and used the factory one as well, caused the same issue as you have.

May 19, 2017 | Western Digital Caviar SE 80 GB Hard Drive

3 Answers

CPU upgrade problem

Hi there

what are your pc specs , like ram ect. So we can find out what is wrong. please check your cpu settings and reset the pc bios to see if that hasnt solved the problem



Nov 12, 2008 | AOpen AK77-8XN Motherboard

1 Answer

ECS P4M800-M V 2.0 wont POST

may u have a grouded DVD drive, did u try another DVD or CD drive? may be it will help.....

Aug 14, 2008 | EliteGroup ECS P4M800-M Socket...

1 Answer

No Video

Its easy to test your MB and CPU.
Just remove all components from *********** board, like CD-ROM, DVD disk, HDD, FDD or any PCI or USB component.
Add a speaker to *********** board.
Add CPU, and without RAM.
Now switch on, there must be along beep for RAM not found, if you don't get any beep it means your MB or CPU is faulty.
In other case if you got the long beep, then switch off and add your RAM to MB and switch on again. Now you will get an ok beep. It means every thing is ok.
Now attach your Keyboard and monitor and listen if you get the ok beep or not and also see the monitor there must be light on your screen and message to insert bootable disk.

If every thing is passed ok, then add your HDD and boot.

I think you can do the rest..

Mar 10, 2008 | MSI K9VGM-V Motherboard

Not finding what you are looking for?
Siemens D1675 Motherboard Logo

Related Topics:

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2263 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18420 Answers

john smith

Level 2 Expert

398 Answers

Are you a Siemens Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides