Question about SYMA Toys industrial Syma S032 Ready to Fly Gyro

1 Answer

Range of control only 3mtr ? SHOULD IT BE MORE ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 56 Answers

Yes. Normal range 50-100 meters depending on surroundings and conditions. I'll assume it's fully charged and remote has it's metal antenna extended and strong batteries. Have you messed with the helicopter's antenna? The grey or black wire that came wrapped around one of the landing skids? If so, you must put it back, coiled tightly but not pulling on connection to circuit board, and not touching the metal frame above the landing skid. If none of these is the issue, or fixing them doesn't help the issue, then your bird is likely defective. Sounds a lot like an antenna that's been mucked with....

Let me know if this doesnt help
r

Posted on Sep 13, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace control switches for a venmar hood fan


[PDF]Download - Venmar

www.venmar.ca/DATA/.../131_5_en~v~Installation_Manual.pdf
Before servicing or cleaning unit, switch power off at ... solid-state speed controldevice. 8. ... should not be allowed to accumulate on fan, filters or in .... We recommend to install the hood at a minimum distance of 24" from an electric range and.

FAQ - Venmar

www.venmar.ca/en-faq.html
Can I use other controls than Venmar controls with my unit? What is the ... Range Hoods. Can I replace an "over-the-range" microwave with a range hood? ... VenmarConnaisseur C270 and C600M · Rocker switch control. Venmar V10 ...

Range Vent Hood Switch Parts In Stock from RepairClinic.com

www.repairclinic.com/Shop-For-Parts/.../Range-Vent-Hood-Switch-Parts
Shop for your Range Vent Hood Switch from our huge inventory. Check our ... RepairHelp for Range Vent Hoods ..... Blower variable speed control switch.

Range Vent Hood Repair Help - Free troubleshooting


Jan 23, 2016 | Venmar Kitchen Ranges

1 Answer

Area/volume of a ellipse


I am afraid I do not understand what you want exactly (ellipse, parallelepiped?). The area of an ellipse with semi-major axis a and semi-minor axis b is given by
Area=PI*a*b

Nov 25, 2013 | Ellipse Visor 91810 - Red Line

1 Answer

I would like to have a longer hose put on my heater it has a 1.5 hose and I would like it to be 3mtr


Rinnai come standard with the hose you have. I know for certain a few years ago you could buy the longer hose (WA Australia). Ring around some of the gas retail shops, let them know the model. I'm sure if you found a shop that sold them they would fit it for you and test it. If your not in Australia ring the Rinnai helpline, make sure it's legal to have a 3M hose and maybe ask them for a retailer close to you if possible.

Aug 30, 2010 | Rinnai Unvented Gas Zone Heater. 99% fuel...

1 Answer

How can I remove the 3m safety stop on my mares Nemo Titanium?


Sorry you cant, The 3Mtr stop alarm is possibly the most important alarm on your computer to avoid you getting the bends. If you take your safety stop just below 3mtrs for the correct amount of time then the alarm wont sound. If you ignore this alarm and dont complete your safety stop you run the risk of DSC. Hope that helps

Jul 06, 2010 | mares Nemo Titanium Computer Great Scuba...

1 Answer

My oven when turned on goes to F1 and the heat is like broil...only the top burner comes on????


Hello,Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

May 28, 2010 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

66993 pizza oven microwave oven combo pizza oven not heating error code f1 microwave part works


Hello, please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

Jul 20, 2009 | Kenmore 63662 / 63664 / 63669 Microwave...

2 Answers

Where can i find motor fan part # 2mtr and 3mtr ingersoll rand compressor ssr-ep25


I would try Grainger (www.grainger.com)

They sell IR compressors and always have a large assortment of parts

Jul 16, 2009 | Ingersoll Rand Type 30 Fully Packaged Ir...

1 Answer

1996 ford contour transmission range sensor


Transmission range sensor and neutral safety switch are the same thing (when you go to buy the part). It's at the top of your transmission. You'll see the shifting cable connected to it. Here are the instructions for adjustment:
Shift Control Linkage
The transmission shift linkage adjustments must be performed in the order in which they appear.

Column Shift

Place transaxle range selector lever in (D) (OVERDRIVE) position or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS). A weight of 1.4 kg (3 lb) should be hung on the transaxle range selector lever to ensure the lever is located firmly on the (D) (OVERDRIVE) or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS) detent.

Loosen manual control lever-to-control cable retaining nut.

Move transaxle manual control lever to OVERDRIVE position or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS), second detent from most rearward position.

Tighten retaining nut to 17-23 Nm (13-17 lb-ft). Check operation of transaxle in each transmission range position. Make sure that park mechanism and transmission range (TR) sensor are functioning properly.

Floor Shift

Position transaxle range selector lever in DRIVE position against rearward stop. The floor transaxle range selector lever must be held in the rearward position using a constant force of 1.4 kg (3 lb) while linkage is being adjusted.

Loosen manual control lever-to-control cable retaining nut.

Move transaxle manual control lever to DRIVE position, second detent from most rearward position.

Tighten retaining nut to 17-23 Nm (13-17 lb-ft).

Check operation of transaxle in each transmission range position. Make sure that park mechanism and transmission range (TR) sensor are functioning properly.



To take it off, it's a couple of retaining bolts and a wiring harness.

Jun 28, 2009 | 2000 Ford Contour

1 Answer

My kenmore oven is beeping and will not stop. the display shows F-1.


Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Dec 16, 2008 | Ovens

3 Answers

My kenmore electronic stove is having a beep with code F1 on the


Please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacment of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal checksum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Dec 15, 2008 | Kenmore 40494 / 40495 / 40499 Electric...

Not finding what you are looking for?

Open Questions:

See all SYMA Toys industrial Syma S032 Ready to Fly Gyro Questions

SYMA Toys industrial Syma S032 Ready to Fly Gyro Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top SYMA Toys industrial Toys Experts

MeAndMyBrain

Level 1 Expert

52 Answers

Terry Hair

Level 3 Expert

4128 Answers

GI Consulting

Level 2 Expert

108 Answers

Are you a SYMA Toys industrial Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...