Question about Office Equipment & Supplies

1 Answer

Gear missing teeth

Is there a way that i can order a gear for my techko sh52408

Posted by on

  • 1 more comment 
  • Anonymous May 30, 2008

    I have a model memorex MPS 2800 . I found the gear connect to Moter shaft with the Ideler gear which is the teeth worn out and I need replacement ( Idler connect to the motor)

  • birddog1298 Jul 29, 2008

    gear missing teeth

  • Anonymous Mar 15, 2014

    Put paper in and overload light comes on



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 58 Answers

This is how a got my hard to fine gear!

Contact Michael Business Machines for your local dealer 1-800-223-2508

Good luck, Tom

Posted on Mar 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2003 toyota camry 4cyl.engine doesnt turn over but starter does.starter ck. and is ok , just makes starter whining noise

if starter motor runs (hear it??) but doesn't turn engine , then it needs to be replaced also at same time , the gear it contacts with on flywheel edge ,needs to be visually inspected (easy with starter removed) for any missing or bent teeth , as a engine this old is bound to have some worn or missing teeth, if gear is missing teeth or are very worn (teeth looks like a shark fin with hook to them) then engine and transmission will need to be separated to be replace the gear , most shops will just remove engine to allow for this , but this isn't always nessacary

Dec 14, 2016 | Toyota Cars & Trucks

2 Answers

Runs but doesn't turn. Worm gear is not broken.

Something must be broken if the motor is turning and the planetary is not. It will be one of the following, we will start from the first point of contact with the armature
1) Worm gear broken (fuse gear) you say no teeth broken
2) Worm gear not broken but whole unbroken plastic part not gripping aluminium boss
3) Pin through worm gear broken or missing
4) Pin through centre (or bevel) gear broken or missing
5) Pin through small gear in planetary broken or missing
6) Pin through planetary hub centre shaft broken or missing

The most common ones in order of likelihood are, 1, 2, 3 and 6

Dec 29, 2014 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

Starter gear missing teeth 2005 Aqula 250 Cruiser

If you mean the starter ring gear behind the rotor then yes it will be easier with the special puller and tools.

Apr 03, 2010 | 2003 Hyosung GV 250 Aquila

1 Answer

How do I figure out the gear ration on a 4X4 front transaxle with the lable missing?

It will be the same as the rear. It the rear is missing you will need to count the ring and pinion teeth. Ring gear teeth Divided by Pinion gear teeth.

If you just want a ballpark idea, you can rotate the driveshaft and count how many revolutions it takes to make the tire go around once. That will be your ratio.

Sep 13, 2009 | 1995 Chevrolet K1500

1 Answer

Not sure about the postion of the missing teeht and valve timing

when there are missing teeth on a cam gear the motor will never run. for as those teeth pass thru it puts the motor out of time again and again , and again

Feb 26, 2009 | 2001 Ducati 748 R

1 Answer

Shredder does not pull in paper to be shredded

If it doesn't accept the paper, more than likely the gear coming off of the motor has broken teeth. I think for this model you have to call the manufacturer. Good Luck!

Feb 18, 2009 | Office Equipment & Supplies

1 Answer

Need Information:

This is how a got my hard to fine gear!

Contact Michael Business Machines for your local dealer 1-800-223-2508

Good luck, Tom

Oct 09, 2007 | Techko SH2106PA Shredder

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

640 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts


Level 3 Expert

102366 Answers


Level 3 Expert

2237 Answers


Level 3 Expert

77947 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides