Question about JVC AV-27530 27" TV

2 Answers

I have dishnetwork tv1 reciever is fine and shows tv2 is working but cannot see nothing but a blue screen on tv2. Dishnetwork will come out for 95.00 but the last 2 times they were here(free of charge), they did not fix nothing. any ideas ive done all that dishnetwork recommends.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I need help with the same thing. I have checked the channel 1000 times. I have unplugged the receiver multiple times. I have pushed the Sat button and the Rec button. I plugged in the new receiver according to the diagram, but there are leftover cables up there and it's hard to see the back of my receiver because it is in a tight spot. I didn't set up the original one, so maybe I set up the new one wrong. Either way, I am also not going to pay $95 that I don't have for a Dish repair person to come do something that I could do. Are there any tricks for plugging in the receiver? Like even though the diagram doesn't show anything plugged into the TV2 ports, something really should be plugged in there?

Posted on Jul 13, 2013

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 123 Answers

We would be happy to help get that fixed right away. Thefirst thing we want to ensure is that all connected equipment is on.Wealso need to know what channel your TV2 is currently on, we will do this byturning the TV off then back on and noting the channel or input that appears onscreen when the TV is powered on, if the TV is not on channel 60 or 73, tune to60 or 73. Then Access "Modulator Setup"from TV1 by pressing"Menu", 6 for "System Setup", 1 for"Installation", then 5 for "Modulator Setup". Tune TV2 tothe channel that appears under "TV2 Out" on screen. If stillno picture and the mode for TV2 is "Cable", change it to"Air" and change the channel on your TV2 to 60, if it is already on"Air" then change it to "Cable" then change TV2 to channel73. If the issue is only on ONE receiver, unplug the DISH receiver for10 seconds and plug back in. The next thing we want to check is the connectionon the back of your receiver labeled "Home Distribution", this cablecarries the picture all the way to your TV2. Start by removing the connectionand screwing it back in, make sure all the connections going to your TV2 arehand tight. These steps should get your TV2 up and running.

We want to thank you for being a valued DISH Network customer!


Phillip Chang
DISH Network Customer Service Representative

Posted on Mar 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I turned the living room tv on this morning and it is black and white and says no signal. The other tvs are working fine. I have turned it off and turned it back on still nothing


Hi my name is Mike Houston of DISH Network and I see youturned on the living room TV and it was black & white and had no signal.Depending if it's a Dual receiver and if the issue is TV1 or TV2 but there issome thing's you can check to make sure it is on the right channel. I will sendyou two links to help with the setup for both TV1 and TV2, if you have anymorequestions or concerns please e-mail me back at Michael.houston@dishnetwork.com;http://www.dishnetwork.com/SupportSection/bbs-screenand http://www.dishnetwork.com/SupportSection/black-blue-tv2.

Sep 04, 2011 | DISH Network 322 DTV Receiver

1 Answer

Umm my tv2 remote isn't connecting to my reciever so i tried to change the remote address and it doesn't work


Hi my nameis Mike Houston of DISH Network and I see your TV2 remote isn't connecting toyour receiver. You will want to make sure you're at the TV1 location to programthe remote for TV2, press the Menu button 2 times and you will see the SystemInfo screen. On the bottom for the screen you will see the remote address forTV2, make sure the TV2 remote has fresh batteries inside. On the back of thereceiver their will be a Remote Antenna port and you want to make sure that ishand tight. Push and release the SAT button and press record and you should seethe address change for TV2. I will send a link to help with these steps; http://www.dishnetwork.com/SupportSection/remote-control.

Jul 30, 2011 | DISH Network 322 DTV Receiver

1 Answer

When I change the channel on tv2, it also changes the channel on tv1. I have changed the address for tv2's remote, but it still changes tv1's channel.


Hi my nameis Mike Houston of DISH Network and I see your TV2 changes TV1 as well, thereis an easy fix to this problem. You will want to make sure the receiver is inDual Mode and then make sure the TV2 connection on the back of the receiver isin the right port. I will send a link to help with these steps, http://www.dishnetwork.com/SupportSection/same-video-2-tvs.I will leave my e-mail if you have any questions Michael.houston@dishnetwork.com.

May 22, 2011 | DISH Network DVR-625 DTV Receiver /...

1 Answer

I have a new DVR 622 reciever, the UHF remote(TV2) does not work at all, I have tried to program it, but itdoes not seem to work.(does the TV2 need to be hooked up to the receiver to et the remote to...


Hi Rich, myname is Mike Houston of DISH Network and after going over your post I see theTV2 remote as well as other issues with TV2. There is a easy fix to this so youcan enjoy both TV's, on the receiver you will want to make sure it's in DualMode, you will see a Yellow, Blue and Green lights on the front of thereceiver. I will send a link to help with the steps of setting up the remoteand making sure the TV2 is configured correctly and on the right channel. http://www.dishnetwork.com/SupportSection/troubleshoot

Apr 18, 2011 | DISH Network ViP622 DVR DTV Receiver /...

1 Answer

I'm in the room and using tv 2 on dvr but I see tv1 and don't know how to go back to tv 2. So what I'm trying to say is I'm watching what tv 1 is watching.


Himarcos_and_s, my name is Mike Houston of DISH Network and I was going over yourpost and with TV2 showing what's on TV1 you want to make sure the receiver isin dual mode and if that is the case please unplug the receiver for 10 secondsto reset the receiver and you will have your TV1 and TV2 showing differentprograms. If you have any questions please e-mail me at Michael.houston@dishnetwork.com.

Mar 22, 2011 | DISH Network Televison & Video

1 Answer

How do I record two channels at once on a DMR-EX773EB DVD Recorder


I cannot find on online manual for this model. If dual channel recording an actual specification for the model? If it really should be able to record two channels at once then it may be similar to the DishNetwork DVR. It has one input but internally splits and creates two different outputs for two different channels.
Check to see if there is a mode setting for single/dual. You will need to set it to "dual". The Dishnetwork DVR has what it calls TV1 and TV2. You can record to TV1 but cannot watch a different channel on TV1 while it is recording. You CAN however watch and record a different channel on TV2 while TV1 is recording. (and vice versa). You can also record two shows while watching other recorded shows.
I'm guessing that you may need to look for some recording options to be able to record two channels at once.

Mar 21, 2011 | Panasonic Televison & Video

1 Answer

I have a Dish receiver 322. TV1 is set on channel 3 and TV2 is set on channel 116. Everything worked. We moved the receiver and TV1 into another room (right next door to where it was). We triple checked...


Hi hartbettinaI see where your TV2 has a blue screen, there are a couple of things you can doyou can do. The first things you want to do is press the buttons of MENU-6-1-5and see if TV2 is set to channel 60 or 73 and make sure TV2 is on that channel.Once TV2 is on the channel on the Modular Setup page you will want to unplugthe receiver for 10 seconds and plug it back in and it will reset itself. Iwill send a link that will help with these steps. http://www.dishnetwork.com/SupportSection/black-blue-tv2

Feb 27, 2011 | DISH Network 322 DTV Receiver

1 Answer

The dish network is not working correctly in another room for two tvs what do I do?


Hi dmarshall020my name is Mike Houston of DISH Network and I was looking at your post and seenwhere your having problems with two TV's in your home. Depending on if it's TV1or TV2 and what is on the screen, if it's a black, blue, or snowy screen willdepend on the channel it is set to. For TV1 you will want it on channel 3 or oneof the inputs of the TV. If it is TV2 you will want to put it on channel 60 or73, I will send a link to help with these steps and if the problem still existplease e-mail me at Michael.houston@dishnetwork.com.http://www.dishnetwork.com/SupportSection/video

Feb 18, 2011 | Insignia NS-LCD19 19 in. LCD TV

1 Answer

My tv2 only shows one channel on dual mode and i cant change the channel with the remote


Hi billabongwanmy name is Mike Houston of DISH Network and what you will need to do isreprogram the remote. You will need to take the TV2 remote to the TV1 location,on the TV1 remote press the MENU button two times and it will take you to theSystem Info screen. You will then press and release the SAT button and pressthe record button one time on the TV2 remote. I will leave the link to helpwith these steps. http://www.dishnetwork.com/SupportSection/setup-remote

Feb 10, 2011 | DISH Network ViP722 DTV Receiver /...

2 Answers

Cannot get it to work with dish network. It won't accept channel input either!


Hello! If your tv just won't cycle to the correct channel you can change the setting if its tv1 you need a channel scan if it's tv2 try these steps:
http://www.dishnetwork.com/SupportSection/video

Daniel Busa
DISH Network Customer Service

Dec 31, 2010 | Insignia IS-LCDTV32 32 in. Television

Not finding what you are looking for?
JVC AV-27530 27" TV Logo

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74251 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...