Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

The washer proceeds into its cycle, beeps then give a code F02 at 34 minutes remaining

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

This information is from repairclinic.com

F/02 Long Drain
If the drain time exceeds 8 minutes, the water valves are turned off and "F/02" is flashed.
NOTE: After 4 minutes the "Sud" error will be displayed, then 4 minutes later the F02 error code will be displayed.

Press PAUSE/CANCEL twice to clear the display.

  • Check the drain hose and make sure it is not plugged or kinked.
  • Check the electrical connections at the pump and make sure the pump is running.
  • Check the drain pump filter for foreign objects.
  • If the above does not correct the problem, replace the pump.
The drain pump filter is located in the front, center of the machine at the bottom behind the lower panel that can be removed by taking out 3 screws.

I hope this helps. Here we are starting with the most obvious. If not the filter, it could be the pump itself, or the flowmeter, but try this first. Handiest1 10-1-10

Posted on Oct 01, 2010

Testimonial: "Took off the front panel and saw the drain cap. Had to drain at least 1 gallon of nasty water, lint with shop vac. Cleaned up, all is well. Thanks"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does it beep through the entire. Wash cycle. No code showing.


Whirlpool Duet GHW9150P Front Load Washer Beeping ...

www.fixya.com > ... > Whirlpool Duet GHW9150P Front Load Washer
Question about Whirlpool duet Washing Machines ... my front loader is not workingwhirlpool washer flashes and beeps will not finish a cycle 1 Beep/E10--Error: Water... It beeps through the wash and rinse cycle every couple of minutes. ... Cycle signal which tells you that the cycle is complete beeps through the entire cycle.

[PDF]front-loading automatic washer use and care ... - Whirlpool

www.whirlpool.com/.../U...

Translate this page Whirlpool Home AppliancesWash. This is the main portion of the wash cycle. You will see the washer tumble the load. ... Spin cycle. If the laundry is still wet, take half of the load out of the washer and try again. .... Using recommended AFFRESH® washer cleaner, add.

[PDF]DISHWASHER USER INSTRUCTIONS - Whirlpool

https://www.whirlpool.co...

Translate this page Whirlpool Home AppliancesThe first cycle using the sensor will run longer to calibrate the optical sensor. Rinse Aid. Using rinse aid will optimize your drying and wash performance. This dishwasher is ...... laundry detergent, hand soap, or dish detergent for hand washing .... models) you will experience more starts and stops throughout the entire cycle.

Continuous Beeping - Whirlpool Duet Sport Washer - The ...

appliantology.org > ... > The Laundry Appliance Repair Forum

Jan 25, 2016 | Whirlpool Washing Machines

1 Answer

What does beeping mean during dry cycle?


My dryer did the same thing, it was so distrubing noise in the middle of drying cycles, so I turned off the sound switch it went away, now it doesn’t peep any more.

Oct 28, 2017 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Stops and beeps on wash cycle


If it's a whirlpool made washer, shift actuator is possibly the problem.

Aug 29, 2017 | Amana NFW7300WW Washer

2 Answers

Trying to self clean oven, error code F5 E1 alarm set off in the first few minutes of the cleaning cycle


F5
- E1 Self clean latch will not
lock

1.
If door latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from
    memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure
    operation is correct.

2. If door not latched:


  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch
    switch to control. If no damage to wires and all connectors okay, proceed to
    step C.
  3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals).
Replace switch if defective.
4. Measure latch switch (unlatch = switch open,
CAUTION - oven light contacts are closed). Replace switch if defective.
5. If
corrections are made in any step, reconnect power to control. Press and hold any
key for 1 minute to clear R failure code from memory. F2 will appear. Press
CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure
remains, disconnect power and replace control.

Note:
Applies to all F5-E... codes.

Dec 31, 2010 | Whirlpool Accubake SF362LXTS Kitchen Range

1 Answer

Kenmore front load washer error code E 10 - washer stops and beeps periodically and needs to have start button pushed again to complete cycle. Seems to happen one minute into cycle and then a coupleof...


1 Beep/E10--Error: Water doesn't enter Cause: Water supply problem, Check kinks and faucets
1 Beep/E10--Error: Water leaks Cause: Water connections loose,household drain clog,oversudsing. Correct problems.
1 Beep/E10--Error: Dispenser drawer is open Cause: Washer will not operate if drawer is open.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jan 11, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

We have a Kenmore Oasis HE.It stopped during the rinse cycle


“F21” (AKA SD) is a Long (SLOW) Drain error (LD). If the drain time exceeds 8 minutes this error code will be displayed. In addition, a “SUDS” error may also be displayed. This may be an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:


1.First, attempt to unplug the washer for at LEAST 30 minutes to reset the Central Control Unit (CCU). Sometimes this is all that is required to correct momentary glitches with the unit. If the error code returns, proceed to step 2.
2.Check the drain hose to make sure it is not kinked or clogged.
3.Check the electrical connections to the pump and ensure the pump is running.
4.Remove the drain pump filter and check for foreign objects and/or debris.
To check the drain pump, click on the following link for step-by-step instructions

http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

May 16, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Whirlpool duet washer problem


The following link explains the "FH" error code:

http://www.fixya.com/support/r615354-fh_error_code_whirlpool_duet_kenmore

First, try to unplug the washer for AT LEAST 30 minutes in an attempt to reset the Central Control Unit (CCU). Sometimes this is all that is required to correct momentary glitches with the unit. If the error code reappears, then proceed with the steps outlined in the link I provided for you.

This is one of the more "involved" error codes that you may need spend some time with. Although, it may NOT be a difficult repair, it still may require some diligence to figure out the cause. I would recommend checking your washer installation for a potential siphoning problem and then check the drain pump as these are the more common causes. If you require additional assistance, please let me know. I hope this helps you.

Jan 04, 2009 | Whirlpool Duet 3.8 cu. ft. Front Load...

1 Answer

The F code


Refer to manual; your filter could be blocked, or something could be clogged in the drain pipes. Plug off the wall & check the pipes, filter first.

Apr 16, 2008 | Kenmore Oasis HE 27062 Top Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2330 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...