Question about HP DesignJet 90 - printer - color - ink-jet InkJet

1 Answer

HAVE AN HP DESIGNJET 90R WHERE THE SCREEN LESS THE LEFT AND RIGHT SIDE OF THE SCREEN IS BLANK AND THERE IS A FLASHING YELLOW LIGHT -

Posted by on

  • 2 more comments 
  • gblase27 Oct 01, 2010

    The printer, as was asked when I submitted my question, has this problem when it is not connected to a printer.

  • gblase27 Oct 01, 2010

    As was asked as I was submitting my question, the printer is off line when I have the issue described.

  • gblase27 Oct 01, 2010

    When I push the Start Button, the system starts to come up and at the same time the Yellow Light starts flashing and the system goes no further.

  • gblase27 Oct 01, 2010

    Additionally, when I try to turn off the Printer from the On/Off Button, it does nothing.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 857 Answers

Follow these steps :
•Log on to your computer and click on the "Start" button. Choose "Control Panel" from the menu, double-click "Administrative Services" and then "Services." Scroll down to the "Print Spooler" service and make sure it is running. If the print spooler is not running, the printer cannot communicate with the computer, and it might flash a yellow light to indicate a lack of communication. Right-click the "Print Spooler" service and choose "Start" and see if that resolves the issue.
•2
Shut down the printer and remove the power cord. Allow the printer to remain off for at least two to three minutes to reset its memory.
•3
Remove the printer cable from the back of the printer, then turn the printer back on. Wait for the printer to come up, then press and hold the power button until a test page begins to print. Printing a test page verifies that there is no physical problem with the printer.
•4
Shut the printer off again, then replace the printer cable and turn it back on. Wait for the ready light to come on, then send a print job to the printer from your computer.

Posted on Oct 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the front panel screen HP DesignJet 4020ps plotter show a blank screen with a blinking green light?


According to the manual, a blinking green power light indicates that the unit is transition between off and on.

Dec 30, 2014 | HP DesignJet 4020PS InkJet Plotter Printer

1 Answer

My cq 81 pc startsup but black screen. totally blank


the caps lock key is flashing a diagnostic code. If it just flashed once then a pause and repeats this continuously then you have an early chipset initialization failure and the motherboard need to be repaired or replaced. If it's flashing some other code a quick google search for "hp diagnostic LED codes" will find the correct cause for the code.

Jan 08, 2014 | Computers & Internet

1 Answer

Power light flashing 2 3


With II flashing, that's a harddrive problem.
With III flashing, that's a Main board or Power Supply.
You need a tech

Aug 12, 2013 | HP DESIGNJET T770 Printer

1 Answer

Error 8:11 HP Designjet T1100ps 44in PS3


Error indicates Formatter,Hard disc & main PCA any one of them faulty.. Through light pattern we can estimate which part is faulty...Read carefully, understand the indications..
Led pattern: Power supply LED as 1
Formatter leds 3nos from left to right as 2,3 & 4..

* indicates "on"
# indicates "off"
& indicates "flashing"

* # # # ....Main PCA
* * # # ....Formatter
* $ # # ....Hard disc
* * * $ .....Main PCA or Formatter
Note down which LED are on.off & flashing,compare with above said indications find out the faulty part..

d4wd6icgpc9laaaaaelftksuqmcc
nloqafiqpfr0pqy6fgsl6z+nlcjwrqeuxlt5siey8sjpc+feblil6+xgwjruzafracof0e359teuwi1ozhlmhrx0xfmcd+bfeilmn5l+ppik2hpic6wgwvpqfwee1yw0nvg1qi9vzo58bnigp4octvkvtsy87834sjn6odbsmoha2eycmv8comsjb7raqh4aaaaasuvork5cyii=

May 03, 2011 | HP Designjet T1100ps Printer

1 Answer

When I turn on my plotter error message system error 08:11


Error indicates Formatter,Hard disc & main PCA any one of them faulty.. Through light pattern we can estimate which part is faulty...Read carefully, understand the indications..
Led pattern: Power supply LED as 1
Formatter leds 3nos from left to right as 2,3 & 4..

* indicates "on"
# indicates "off"
& indicates "flashing"

* # # # ....Main PCA
* * # # ....Formatter
* $ # # ....Hard disc
* * * $ .....Main PCA or Formatter
Note down which LED are on.off & flashing,compare with above said indications find out the faulty part.. 11_19_2011_3_40_14_pm.jpg

Apr 19, 2011 | HP Designjet T1100ps Printer

1 Answer

ERROR CODE 18:10


Error indicates Formatter,Hard disc & main PCA any one of them faulty.. Through light pattern we can estimate which part is faulty...Read carefully, understand the indications..
Led pattern: Power supply LED as 1
Formatter leds 3nos from left to right as 2,3 & 4..

* indicates "on"
# indicates "off"
& indicates "flashing"

* # # # ....Main PCA
* * # # ....Formatter
* $ # # ....Hard disc
* * * $ .....Main PCA or Formatter
Note down which LED are on.off & flashing,compare with above said indications find out the faulty part.. 11_19_2011_3_40_14_pm.jpg

Nov 29, 2010 | HP Designjet T1100ps Printer

1 Answer

Hp designjet 2000cp code 050000 00180516 help us .


05000, on the 2000cp is the printer can not find the mark encoder, inside your printer there is a roller running left to right that the media will sit on,
on the far left side were the roller ends there is a small piece of white plastic that should sit in the vertical position. the sensor on the carriage is not able to find this.
Once you see it, clean with a q-tip, slightly dampened, and also change the lens on the carriage.
Power on the printer when finished and see if it will go to the ready status,

Oct 10, 2009 | HP DesignJet 2000cp InkJet Printer

1 Answer

HP DeskJet 648c InkJet Printer Problem


one of your staff addressed it completely via chat

Sep 05, 2008 | HP DeskJet 648c InkJet Printer

Not finding what you are looking for?
HP DesignJet 90 - printer - color - ink-jet InkJet Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

102366 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...