Question about Weiser Lock Powerbolt 1000 Lock

1 Answer

Bought a house with one of these on it but no code was left...how would I go about changing the code?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

On the link below page 3 will tell you how to program the lock.

http://www.weiserlock.com/PDFs/install_sheets/pb_eng_install.pdf

Good Luck and please rate 4 thumbs up for the free answer

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change code user 1 on a gem-rp8


I am in the same boat. We bought a house with this system installed in it. How can we change the user 1 code?

Nov 10, 2013 | Gemini Sound Products Napco Gemini Gemrp8...

2 Answers

We bought a house with this lock and don't know how to cancel the previous code and start a new one. We don't know how many digits to put in for the code.


To change your code:

1. Remove the inner cover plate from the lock.

2. Locate the small round reset button near the left side of the circuit board (Red or Black).

3. To program, press the reset button once, then enter your 4-8 digit code on the exterior keypad, then immediately press the middle lock button on the exterior keypad. You will hear a beep. This signals that your code has been accepted.

4. To enter a second code, follow the same procedures as in step 3, but this time press the reset button twice then enter your code.


hope this helps

John

Sep 16, 2011 | Weiser Lock Powerbolt 1000 Lock

1 Answer

No instruction manual


There is a full program and instruction manual on Kwikset.com

Oct 02, 2009 | Kwikset 909 909-15 Satin Nickel Smart...

1 Answer

I need to know how to change the code on a Lockey 2210 Mechanical Push Button Lock (I think that's what it is). The lock was on the front door of the house when I bought it so I don't have the manual. I...


I also moved into a house with a Lockey unit and not operating manual. The following website states this is the way to change the code ... although I have not yet tried doing it. Bit of a bummer that you must take the lock off, but I suppose it makes sense if you want the security ....

http://www.totalproductsales.com/acatalog/info_58.html

Aug 14, 2009 | Lockey Digital M210 Mechanical Keyless...

1 Answer

How to change code


Take the cover off the back of the unit where you are supposed to install the batteries. The instructions should be inside the cover. Hope that helps.

Jun 03, 2009 | Kwikset 907 907-15 Satin Nickel Powerbolt...

1 Answer

Left directional light intermittent to plain out...


I was once a fleet manager with many Jeep Grand Cherokees 1999-2002. We had TREMENDOUS problem with REAR tailight housings. It seem the tailight/signal/back-up light circuitry is embedded in the plasticx of the housing. NO WAY to repair. Replaced with a new one from Jeep. Problem gone. ( at least until the other side went bad ) Not a guarranty, but it's a good chance it has the same problem.

Mar 31, 2009 | 2007 Jeep Grand Cherokee Overland

2 Answers

How do i change the time on this watch?


Try to find it here:

http://www.nike.com/timing/

Rate, please.

Mar 29, 2009 | Nike Midsize Triax 50 Regular Watch #R0082...

1 Answer

I get an "F1" code on my Maytag range.


you need a new temperature probe. its usually located in the upper left hand corner in the rear of the oven.

Mar 19, 2009 | Maytag MES5570 Electric Kitchen Range

Not finding what you are looking for?
Weiser Lock Powerbolt 1000 Lock Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Weiser Lock Locks & Locksmithing Experts

Cindy Wells

Level 3 Expert

5052 Answers

john h

Level 3 Expert

10917 Answers

ray gallant

Level 3 Expert

41378 Answers

Are you a Weiser Lock Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...