Question about OKI C3200n Led Printer

1 Answer

Hi, is there a way to stop the OKI 3200n printer from demanding a new belt, the printer is working just fine but the darn red light stays lit

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 78 Answers

It will continue to report this until replacement. In my experience, it won't lock you out, but the error is a result of the printer testing the integrity of the belt, so until it is replaced, it will report this error. Use it until yu see print issues, and then replace.

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed front signal n now the signals all still work but on the back the signals dont stay lit up they only blink when the signals r on but the brake light works fine on both sides


Traditionally, almost all of the modern produced motorcycles are set up this way. The front 2 lights stay lit, while the back 2 stay off while not activated. The only concern is, the brake light is activated by either switch, and the tail light is full time on. Some state laws in the US demand that your headlight remain on. You're good!

Aug 20, 2013 | Motorcycles

1 Answer

Oki C5510 'Unable to detect printer'


If you have all the led's lit and they are not flashing it means the printer is in download mode. In other words its waiting for you to download new firmware. Look at OKI's site and find the firmware and follow the instructions. That's why you cant install drivers because the printer no longer knows what it is!

Jun 17, 2017 | OKI C5510 MFP All-In-One Led Printer

1 Answer

2003 ford escape seat belt warnign light


Probably no need to see an expensive mechanic. My seat belt warning light came on a few days ago when there were four people in the car and the rear seat belts weren't fastened (I thought that was why it lit up). However, the light came on and stayed on when I was the only person in the car. Logically, it suggested a bad connection somewhere, so I checked the connector under the passenger seat and made sure it was properly fastened together. I then sprayed a small amount of WD40 into the female clasps of both front seat belt connectors, clipped and unclipped the belts a few times and the light is now fine. Try it - it worked for my 2003 Escape.

Jun 03, 2012 | 2003 Ford Escape

1 Answer

The running belt motor does not work, everthing else works fine the belt will just not turn- no noise or anything


You need to pull the motor hood off to see if the belt is still on the motor. If it is and the motor is not turning, check the controler ( located on the otherside of treadmill) and you should see a red light on. When you tell the treadill to go.... the red light should start to flash, if it does then you need a new motor. If it just stays lit, you have lost communication from the console ( the upper controls ), and need to find out if something came dissconnected.

Hope this helps

Nov 10, 2010 | Horizon Fitness Horizon T91 Treadmill -...

1 Answer

JUST BOUGHT A OKIDATA 321 TURBO 9 PIN PRINTER OFF EBAY. WE HAD ONE BEFORE & IT QUIT WORKING SO WE ASSUMED WE COULD JUST PLUG THIS ONE IN & IT WOULD START WORKING BUT THE ALARM BUTTON KEEPS COMING...


If the alarm light is lit constantly it usually indicates that the paper is not loaded, it should go out when paper is loaded. If it is coming on and staying on for a while during printing then there is a problem with the paper out sensor and it may need cleaning. If it is flashing then the other lights that are lit indicate the problem.

Nov 18, 2009 | OKI MICROLINE 320 Turbo Matrix Printer

1 Answer

OKI C3200n and HP LaserJet 3052 Can't be in the same PC


You do not say what operating system you are using?. They are both compatible with Windows 10.There should be no conflict between the two printers. Use system restore and go back in time before you had the problem. Disable your antivirus and try and install them again. That should work.

Jun 26, 2017 | OKI C3200 Led Printer

3 Answers

OKI C3530N


Take cartridges out of the printer.
Close cover.
Unplug printer for 30 minutes.
Reconnect printer to power.
Printer demands cartridges.
Reinsert cartridges as demanded.

Oct 31, 2008 | OKI C3530N Color MFP Printer

1 Answer

Printer won't print labels


What driver are you using ? the default driver should be IBM Proprinter.
Hope this helps
Dezzi

Jan 24, 2008 | OKI MICROLINE 320 Turbo Matrix Printer

Not finding what you are looking for?
OKI C3200n Led Printer Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top OKI Office Equipment & Supplies Experts

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

386 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

SiNnA
SiNnA

Level 1 Expert

38 Answers

Are you an OKI Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...