Sky box will not come off standby cannot access sky tv

There may be a problem with your tv setup.Perform the following steps below:
1.Press the standby button on your Sky remote and switch off your Sky box at the mains. Check that the power light on the front of your Sky box is off before proceeding.2.Check your cable connections 3.Switch your Sky box back on at the mains. Wait 4 minutes before pressing the sky button .You may see a message before viewing resumes, on Channel 998.Tthat's it

Please try 0863 for Hyundai Televisions To program your Sky remote control using the 4 digit code

1. Switch on the TV set
2. Press the TV button on the Sky Remote
3. Hold down the Select and Red buttons for 2-3 seconds until the LED blinks twice
4. Press the TV button on the Sky Remote again
5. Enter 0863
6. The LED should blink twice, if not recheck the 4 digit code used and go back to 1
7. Press the standby button on the Sky Remote (The TV should go to standby)
8. Press the Select button to store

If the TV does not go into standby press the TV button then the standby button, then TV then standby, keep repeating this until successful. This will scan the codes used for a particular make of TV.

Please keep me posted.

Thanks.

Lor04

1) Switch on the TV set
2) Press the TV button on the Sky Remote
3) Hold down the select and red buttons for 2-3 seconds until the LED blinks twice
4) Press the TV button on the Sky Remote again
5) Enter the 4 digit code for your make of TV (try 0206)
6) The LED should blink twice, if not recheck the 4 digit code used and go back to 1
7) Press the standby button on the Sky Remote (The TV should go to standby)
8) Press select to store this setting If the TV does not go into standby press the TV button then the standby button, then TV then standby, keep repeating this until successful. This will scan the codes used for a particular make of TV.

I also have an LG TV. I used this 4 digit code: 0742.

TO PROGRAM THE remote USING THE 4 DIGIT CODE:

1. Turn your TV on.

2. Press tv on your Sky remote control.

3. Hold down select and the red button together for about two seconds, until the red light on the Sky remote control blinks twice.

4. Press tv on your Sky remote control again.

5. Key in the four digit code for your brand of TV. The light on the Sky remote control blinks twice. If the light blinks once only, recheck the code for your brand of TV and start again at Step 1.

6. Press the standby button on your Sky remote control. If your TV switches off, press select. The light on the Sky remote control blinks twice (code stored). If your TV does not switch off, press tv, then press the standby button. Repeat this (press tv, then standby) until your TV turns off, then press select (stores code).

Hi,

Always turn on your TV with the Sky box (or any other external device you want to use) turned OFF. When the TV is on, turn on the Sky box by pressing the "Sky" button at the top centre of the remote control. This will ensure that the TV recognises that there is an external input and it will automatically switch to the correct channel. It also ensures that your Sky remote control isn't in TV mode.

If you switch your TV to standby using the Sky remote after watching, the next time you use the Sky remote, it's still in TV mode. This is why your TV channels are jumping around.

Hope this helps.

You have to programme the correct code for your TV into the Sky remote.

You can get these via "Sky Active" (if your box is connected to a phone line) or from the Sky website, or google search: "Sky remote codes".

However your sky remote wont necessarily control more recent televisions unless you have a REV8 remote control. You can check this by taking the battery cover off your remote and looking at the sticker inside. If it says RC1600/00 you're probably not going to be able to control your TV. REV4 and REV6 are more likely to work - but not guaranteed. If it says REV8, then you are probably not using the correct code or you're not programming the remote correctly.

If you have REV8, the correct code for your TV (according to Sky) is: 0678 or 1678 or 0254

Sky remote code finder page is here: http://sky.uebv.com/

Sky guide to finding your remote code and programming remotes is here:

http://www.sky.com/helpcentre/tv/sky-remote-control/program-your-sky-remote-control-to-work-with-your-tv/

Please rate my solution if you find this helpful. Thanks.

Reset your Sky Box. That fixes 98% of all problems, disconnect from power reset, button at rear usually. Power back up, this may just fix your problem. Otherwise, get the Sky unit replaced.

Just got an LG 42LH2000 and code 0206 works

The code you need is 0145

1) Switch on the TV set
2) Press the TV button on the Sky Remote
3) Hold down the select and red buttons for 2-3 seconds until the LED blinks twice
4) Press the TV button on the Sky Remote again
5) Enter the 4 digit code for your make of TV
6) The LED should blink twice, if not recheck the 4 digit code used and go back to 1
7) Press the standby button on the Sky Remote (The TV should go to standby)
8) Press select to store this setting
If the TV does not go into standby press the TV button then the standby button, then TV then standby, keep repeating this until successful. This will scan the codes used for a particular make of TV.

Hi.

Its a long shot but try this,
It can cause problems when you switch set to & from stand bye.

Check that you are viewing a digital TV channel
Enter the menu and navigate to:
Setup > System > Software Upgrade > Standby Mode upgrade
Change the setting to Off.

I cant gteee that this will sort your problem out so post here if it doesnt & I will check samsung data base.

http://dysonmanuals.llc.nu/

Chris..