Question about Kenwood Car Audio & Video

1 Answer

There is no option for the 'demonstration mode' to be either turned off or on, therefore i cannot turn it off!! How do I do this? Thanks...

Posted by on

  • 3 more comments 
  • terrypscott Sep 29, 2010

    I'll give it a shot, give me a minute and i'll let you know? thanks

  • terrypscott Sep 29, 2010

    Hey, I tried wht you said to do and I can now get the 'demo' option displayed but cannot turn it off? The model is kenwood kdc-w3041,
    Can you help? many thanks...

  • terrypscott Sep 29, 2010

    Yeah, once I had done that I left the stereo on standby, held the b. boost button down for the menu to come up then flicked through the menu. which then the 'demo on' option came up, but it wont let me turn it off?!?! any ideas?

    Thanks

  • terrypscott Sep 29, 2010

    Absolute genuis mate, thanks very much!! Only had the stereo a couple of days but it's been doing my head in constantly!! Must have spent about 2 and a half hours in the car after work tonight!! However all sorted now, cheers buddy...

    Terry

  • terrypscott Sep 29, 2010

    Absolute Genius, Many thanks, Terry

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,777 Answers

What is the model of the deck you are using? Usually you can hold down MENU or SETUP for a few seconds and it eventually comes up with options, try that and if nothing happens reply back with the model number.

Thanks
Tim

Posted on Sep 29, 2010

  • 4 more comments 
  • Tim Grayson
    Tim Grayson Sep 29, 2010

    Actually I just found this as well, if the before mentioned recommendation doesnt work, try holding down "5" if your deck has this, and press the reset button in with a PEN.... BUT KEEP HOLDING DOWN 5 AFTER PRESSING RESET, and eventually it exits demo mode.

    Strange, but it works on most Kenwood decks

    Tim

  • Tim Grayson
    Tim Grayson Sep 29, 2010

    Sounds good! Let me know
    Tim

  • Tim Grayson
    Tim Grayson Sep 29, 2010

    Do any other buttons function? You can get a demo mode menu? There should be a way to exit from there. You held down the 5 button for a while before and after pressing reset correct? I am checking more now, but please verify.

    Thanks
    Tim

  • Tim Grayson
    Tim Grayson Sep 29, 2010

    Ok here is what you need to do.

    The first step it says is "enter menu mode" to do that, hold the B. BOOST button for at least 1 second

    Then select the demonstration mode with the control knob (top or bottom of the knob)

    Press the center of the control knob for at least 2 seconds to "toggle" the mode on or off, it should say DEMO OFF when off.

    There we go!

    Tim

  • Tim Grayson
    Tim Grayson Sep 29, 2010

    Hope you saw my other post, get to that DEMO ON screen and hold down the control knob, press it in the middle, for at least 2 seconds, then it goes to off.

    Tim

  • Tim Grayson
    Tim Grayson Sep 29, 2010

    Also once you have it off please make sure you come back to the question here and click the Accept This Solution button otherwise I get no credit for the help.

    Thanks!
    Tim

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i get the demonstration of the screen


There is usually an option in the menu to turn the DEMO off. Not sure the exact model number of the camorder that you are referring to. DEMO mode acts as a type of screensaver. It will start demonstration if the camorder is left sitting idle too long.

Hope this helps.
www.austintelstarservices.com

Jul 20, 2011 | JVC Video Cameras

1 Answer

The reciver is stuck in demo mode. Can`t get it out of demo mode.


The demonstration will activate the first time you turn on
the power. When the demonstration starts, the following
message appears in the display:

“NOW DEMONSTRATION MODE IF YOU FINISH DEMONSTRATION PLEASE PRESS POWER KEY WHILE THIS MESSAGE APPEARS IN THE DISPLAY THANK YOU”

To cancel the demonstration
Press the Power 1/0 button to turn the receiver off while the above message is being displayed. The next time you turn the receiver on, the demonstration will not appear.


It's in the manual - page 3.

Jun 10, 2010 | Sony STR-DE445 Receiver

1 Answer

Whenever i turn off the mains, i get a Demontration message after power on.


From the manual:

Demonstration Mode
The demonstration will activate the first time you turn on
the power. When the demonstration starts, the following
message appears in the display:
“NOW DEMONSTRATION MODE IF YOU FINISH
DEMONSTRATION PLEASE PRESS POWER KEY
WHILE THIS MESSAGE APPEARS IN THE
DISPLAY THANK YOU”
To cancel the demonstration
Press ?/1 to turn the receiver off while the above message
is being displayed. The next time you turn the receiver on,
the demonstration will not appear.
To view the demonstration
Hold down SET UP and press ?/1 to turn on the power.
Notes
• Running the demonstration will clear the receiver’s
memory. For details on what will be cleared, see
“Clearing the receiver's memory” on page 15.
• There will be no sound when the demonstration mode is
activated.

and...

Note: If the AC power cord is disconnected for about two weeks, the receiver’s entire memory will be cleared and the demonstration will start.

Mar 17, 2010 | Sony STR-DE445 Receiver

1 Answer

Turned off demo mode but it turns back on on its own


Viewing the demonstration (DEMO) mode
The DEMO mode automatically demonstrates several features of
your TV.
To start the DEMO mode:
1. Press MENU.
2. Press left or right button to highlight the SET UP menu.
3. Press up or down button to highlight DEMO.
4. Press left or right button to highlight START.
To stop the DEMO mode:
Press RECALL, EXIT, or POWER.
I hope this helps. Thanks for using fixya.

Jan 20, 2010 | Toshiba 36A43 36" TV

1 Answer

Stuck in demonstration mode


Hi,

Turn the Machine OFF. Then, Press and Hold the Start Button and ON/OFF Button at the same time for few Seconds and it would fix the issue.

Let me know, if problem persists, with Make and Model of the Washer.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Jan 10, 2010 | Bauknecht Dishwashers

2 Answers

Microwave timer counts down super fast


try unplugging it for about 15 minutes. if that doesnt work, you might as well get a new one. i fix everything myself for just the cost of parts and i have found that what parts cost for a microwaves, its cheaper just to buy a new one.

Oct 17, 2009 | Sharp R-540DK Microwave Oven

2 Answers

Timer runs extra fast and microwave does not heat


I had this same problem with my Maytag Microwave. Unplug the unit and plug it back in. It fixed my issue.

Sep 04, 2009 | Maytag Microwave Ovens

1 Answer

The function DEMO MODE can´t be set off. I want to set any wall paper and the DEMO MODE stay ON.


CLICK HERE for a PDF version of your manual.

To turn OFF DEMO mode - go to page 50 of the manual.... and find the following-

1 Select the Demonstration mode
Push the Control knob to [FM] or [AM].
Select the "DEMO Mode" display.

2 Set the Demonstration mode
Press the Control knob for at least 2 seconds.
Each time the knob is pressed at least 2 seconds,
the Demonstration mode switches as shown
below.

Demo Mode "ON"
Demo Mode "OFF"

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Apr 10, 2009 | Kenwood KDC-MP7028 CD Player

1 Answer

Philips magnavox fw-c1 3cd, 2 cassette, am/fm stereo


To stop the demonstration mode
• Press and hold stop (on the system
only)
for five seconds when the
system is in demonstration mode.
ª The demonstration will stop.
ª "DEMO OFF" is displayed.
ª The system will switch to standby
mode.

Feb 27, 2007 | Philips FWC1 CD Shelf System

1 Answer

Demo


To stop the demonstration mode
• Press and hold stop (on the system
only)
for five seconds when the
system is in demonstration mode.
ª The demonstration will stop.
ª "DEMO OFF" is displayed.
ª The system will switch to standby
mode.

Feb 26, 2007 | Philips FWC1 CD Shelf System

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4869 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...