Question about Vtech t2121 Cordless Phone

3 Answers

When trying to make a call "can't connect" appears on the screen. i have tried resetting it.. unplugging everything for 5 minutes and the same command appears. what do i do?

Posted by on

  • 4 more comments 
  • janellebelai Sep 29, 2010

    no how do you do that?

  • janellebelai Sep 29, 2010

    i didnt register it to begin with. can i still do that? if so how?

  • janellebelai Sep 29, 2010

    i'm not getting quick responses

  • janellebelai Sep 29, 2010

    hi

    you did not include the link to download the manual..

  • janellebelai Sep 29, 2010

    can you tell me where to find a manual??

  • janellebelai Sep 29, 2010

    i've downloaded the manual however there is no instructions on how to set the frequency. there is only information saying what the frequency is or should be

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,278 Answers

Hello.

Plug a different phone into the same jack to see if the problem is the phone or the jack.

Hope this helps.

Posted on Sep 30, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Expert
  • 2,973 Answers

It seems that the phone can not communicate with the base. And for that you must set the same frequency on both. How? Read the manual and act accordingly. If you do not have the manual the follow the link below to download one.

Posted on Sep 29, 2010

  • Rinoo Kumari Sep 29, 2010

    Sorry. My fault. the link I spoke about is below. Download the manual from here.
    http://www.retrevo.com/s/Vtech-t2121-Tel...

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,566 Answers

Hello,

Have you tried re-registering the handset already?

Posted on Sep 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

I have a uniden Tru9466 base station and a uniden TWX 977 that the later that was previously registered with the first displayed a out of range notice so I went thru the process in the owner's manual...


Welcome to FixYa.

  1. Turn OFF your handset (TWX977) and any other handset registered to the base (9466).
  2. Unplug the base from its power source.
  3. Unplug the phone line from the base.
  4. Wait for 15 mins.
  5. Plug back the power source and the phone line.
  6. Turn ON the handset (TWX977)
  7. Reset the handset (TW977) by doing the following:
  • Press the MENU soft key. Select the DEREGISTRATION submenu.
  • ARE YOU SURE? appears. Move the cursor to select YES. Press the OK soft key.
  • To clear other handset information, please follow these steps:
  • From the handset, press and hold [ ] and [#] for more than 5 seconds. Select the DEREGISTER HS submenu.
  • Move the cursor to select the handset ID to be de-registered from the list, and then press the OK soft key.
  • DEREGISTER HS appears. Move the cursor to select YES. Press the OK soft key.
  • ARE YOU SURE? appears. Move the cursor to select YES, and then press the OK soft key. You will hear a confirmation tone.

8. Register the handset by doing the following:
  • With the base in standby, press the MENU soft key.
  • Move the cursor to select REGISTER HANDSET. Press the OK soft key.
  • On the handset, press and hold [#] until you hear a beep.
  • While the handset is registering, HANDSET REGISTERING will appear in the LCD. When REGISTRATION
  • COMPLETE is displayed; the handset has been registered to the base. If REGISTRATION FAILED appears,
  • please try these steps again.

Thank you for using FixYa.
Have a great day.
Jas247

Aug 22, 2011 | Uniden TRU9466 Cordless Phone

1 Answer

My TV was working and then all of the sudden the screen went blank and now there is a flashing red light that appears. I tried to turn everything off and back on (the universal solution to everything) but...


Hello

There is something confusing the system control of your TV and it should me resetted. To reset it, just switch OFF your TV with its front panel power control switch, and after that, unplug the TV from the wall socket. Wait for about 5 minutes or so, and the plug it and switch It ON. If this does not work for the first time, give some more time to reset, say about an hour or so, and try. OK.

Jan 29, 2011 | Philips 37PFL5332D 37 in. LCD Television

1 Answer

My sharpe aqous runs for so long then a message appears saying the tv will automatically switch of in 5 mins, this appears every minute until the 5 mins are up. I have checked and the sleeper timer is set...


Tries unplug,replug tv an hour later.Let the tv reset itself.Than goto tv Menu go to PICTURE,go down to reset.This will reset everything on the tv Tuner board back to factory setting.This should solved ur problems.Not,than the tv Tuner board have intermitten isuse problems.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish Tuner board for the replacement.

Sep 13, 2010 | Sharp Aquos LC-37GD6U 37 in. LCD HDTV

2 Answers

Wii will not load past Health and Safety screen.


Hi,

Try a hard-reset. Unplug the console from the Mains For 5-10 Minutes.
Wii returns back to default settings.

Thankyou for Using Fixya.

Mike @ Compurepair.

Jan 19, 2009 | Nintendo Wii Console

1 Answer

Mitsubishi 65in


try unpluging for 5 min then try again..this should reset it!

Nov 07, 2008 | Mitsubishi WS-65313 65" Rear Projection...

1 Answer

There is no picture on the screen yet we can here everything that is being said and change channels and listen to everything but there's just a blank screen.


Good Day, Gibbler;

No picture, has audio.....First try resetting the TV (unplug from a/c from wall), wait 3 to 5 minutes then plug back in. If it is a MIT's check for fluid on PCB's.

Good Night & Luck, big IRISH.

Aug 16, 2008 | Televison & Video

1 Answer

Monitor menu screen appears on screen


Try a hard reset: Unplug from power source, disconnect from PC and wait for 10 minutes. Reconnect everything and see if the issue is resolved.
If not, then you either have a loose contact on the menu button or failing circuitry. I'd recommend calling Sharp tech support in this case..

Jun 14, 2008 | Sharp LL-193AB 19" LCD Monitor

1 Answer

Speakers killed my moniter


Well as you have already tried disconnecting the peripherals from your computer, and tried restarting the computer too which did not help you, it sounds to be an hardware issue with the monitor. However if incase you have not tried this, you can disconnect the monitor completely from the tower, power on the monitor, if it powers on and you get a message as no signal, your monitor is working good. If not replace the monitor. If the message appears on the monitor screen, disconnect everything from the tower, push and hold the power button on the tower for a minute. Connect just the monitor and check for any display. If you do get display, thats good, connect one device at a time and check to see if the display appears.

If theres no display with just the monitor connected, the issue would be with the graphics card. You may need to replace it or get the system repaired.

May 27, 2008 | Dell Dimension 2400 PC Desktop

3 Answers

Hi, we have a goodmans GTVL27W23HD that was left on standby for 6 days, now will not show the digi-box channel, just a blue screen, sound only on scart 1 any suggestions anyone? something re-setting...


Try to unplug everything and plug it back in at the correct order(without power). Then plug the power and into the items in the correct order and let them power on for about 5 minutes. With the blue screen that may take about 15-20 minutes.

Apr 19, 2008 | Televison & Video

2 Answers

NEtgear RP614 cannot connect after a electricity shortage in our home :(


How is it not working? You get limited or no connectivity or it isn't functioning at all. Firstly, let's do a power cycle. Push the reset button for 5 seconds, unplug for 45 seconds, and reset 5 seconds, and unplug for 45 seconds. If that doesn't work try a hard reset. Alright, it's time to do a hard reset, this will rest all your passwords, Take a Pen or a pin, push the pin the the reset hole for 45 seconds, Uplug the modem for 1 minute, reset hole for 30 seconds, unplug for 30 seconds, and it should be hard resetted also power cycle.

Aug 25, 2007 | NetGear RP614 Router

Not finding what you are looking for?
Vtech t2121 Cordless Phone Logo

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vtech Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Cindy Wells

Level 3 Expert

5183 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18407 Answers

Are you a Vtech Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...