Question about Brother HL-5270DN Laser Printer

Open Question

I have the Brother HL-5270DN model and i have a problem. When the toner finished (error message : the toner life end), i replaced the toner with the new one. However, the printer can not print pages ("replace the toner cartridge" is the new message). What can i do now?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ctf1800
  • 4402 Answers

SOURCE: brother dcp 7020 says toner end life

unplug plug it back in, did you remove the protective cover and clean coria wire?
http://welcome.solutions.brother.com/BSC/public/us/us/en/faq/faq/000000/000000/000065/faq000065_018.html?reg=us&c=us&lang=en&prod=dcp7020_us

Posted on Dec 20, 2007

Ad
  • 1 Answer

SOURCE: Brother HL-5270DN PF Kit Problem

I found the answer in another group, from Sunshine3240:

Open the front cover and leave open while completing the following steps:
Turn the printer off.
Hold the 'go' button while turning the printer on. All panel lights should be on.
Release the 'go' button.
Press the 'go' button 2 times.
Pause.
Press the 'go' button 5 times.
The toner light should be off.
The paper light should be on.
Close cover. The ready light should be the only light on.


Posted on Mar 13, 2009

  • 4 Answers

SOURCE: how to get ride of Toner life end message

You could try resetting the toner cartridge settings. OPen the machines front door where you would replace the cartridges. On the top panel you will see a "clear/back" button. Press it and on the display you will see a reset menu come up. Arrow to each one and hit the OK button. Press "1" to reset. Once you have gone through all close the front door of the machine and press stop to bring the display back to normal.

Hope this helps.

Posted on Oct 21, 2009

SOURCE: I have the Brother HL-4070CDW and I have a TONER

With the front access door open, press and hold the cancel button. While still holding the down the cancel button, press and hold the reprint button... you should now see the toner reset menu. Why we can't get there from the machine info/reset menu to begin with, well, guess Brother wants to sell you more toner. ;^)

Posted on Jan 09, 2010

  • 1 Answer

SOURCE: cannot remove toner cartridge from Brother HL 2170W

Had same problem. The instructions don't tell you that it is not just the cartridge that needs to be pulled out but the frame (black metal thing) inside which it sits. The whole thing pulls out. Of course, you have to press the green tab too.

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error toner hl 2140


Toner end of live: http://www.instructables.com/id/Brother-HL-2140-Toner-Life-End-Error-Hack/

May 29, 2017 | toner Office Equipment & Supplies

1 Answer

End toner reset


Replace the toner cartridge and it will reset the page counter automatically.

Sep 15, 2014 | Brother HL-5270DN Laser Printer

1 Answer

Brother HL-6050dn Toner Life End Message Tried covering the eye Tried Go-Set and changing to Nothing solution Still red message saying Toner Life End


I just got through this problem, The customer had a "refilled cartridge.
The Flag on the left side near the gearset of the Toner cartridge was not
brought back to the proper position, just undo the three srews and reset the flag.
works like a champ,. your welcome.

Dec 08, 2010 | Brother HL-6050DN Laser Printer

2 Answers

Help me with reset fuser problem on Brother HL-5270DN


HelloTo reset fuser on your HL-5270DN you have to press "Go" and "+" at exactly the same time. You will be given an extended reset menu. Then you will go for fuser reset.
Plz sure the fuser must be OK/replaced before applying this action
Good luck
Do rate the solution if got help

Dec 06, 2010 | Brother HL-5270DN Laser Printer

1 Answer

After replacing old toner with a new one error message comes up saying Toner Life End. Could you please advise of possible solutions?? thank you


device on left side of frame is stuck open .Not leting it see new toner unit. Half to remove left side cover and put it back in place.

Aug 12, 2010 | Brother HL-5270DN Laser Printer

1 Answer

My HL-2140 brother laser printer is flashing a red error


1>If the toner lite is blinking , it's mean the toner life near to end. In these case please replace the toner cartridge.
2>f the drum lite is blinking , it's mean the drum life near to end. In these case please replace the drum.
I hope it will help to solve your printer problem.

Feb 09, 2010 | Brother HL 2140 Laser Printer

2 Answers

Brother hl-5270dn is desplaying the error code S01? What does this mean?


S01 = Fatal error EX
1) turn off the printer
2) wait a few seconds
3) turn it on again

H63 = DRAM access error
1) turn off the printer
2) wait a few seconds
3) turn it on again

Sep 11, 2009 | Brother HL 5250DN Laser Printer

2 Answers

Brother Laser HL-5240 has a status light and toner light. Fuser was replaced but no help.


that error usually indicates that the toner has reached its end of life
or the drum is not properly installed.

i had one person who put the toner in but threw the drum cartridge away.

Jun 25, 2009 | Brother HL 5040 Laser Printer

2 Answers

Brother HL-5270DN PF Kit Problem


I found the answer in another group, from Sunshine3240:

Open the front cover and leave open while completing the following steps:
Turn the printer off.
Hold the 'go' button while turning the printer on. All panel lights should be on.
Release the 'go' button.
Press the 'go' button 2 times.
Pause.
Press the 'go' button 5 times.
The toner light should be off.
The paper light should be on.
Close cover. The ready light should be the only light on.


Jan 06, 2009 | Brother MFC-8460N Laser Printer

2 Answers

Toner End Life


Ther is a small viewport (about 1/4" dia) on each end of the cartridge that a photo sensor apparently shines through. The port is not near the bottom, so there's room for plenty of toner below it. Put a small piece of electrical tape over one of them and it will print fine..
Just a thought it worked for soe of my frnds..its worth a try..
Good luck!

Oct 24, 2007 | Brother HL-6050DN Laser Printer

Not finding what you are looking for?
Brother HL-5270DN Laser Printer Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

James Cagle
James Cagle

Level 2 Expert

455 Answers

Samyfam
Samyfam

Level 3 Expert

379 Answers

Are you a Brother Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...