Question about Jenn-Air JER8855 Electric Kitchen Range

Open Question

I have the Jenn-Air JER8855AAS model I got from Home Depot Expo many years ago (I can't remember when but maybe 15 or so years ago) and yesterday the control panel had a F9 and then F1 and then it went off. We unplugged the oven and plugged it back in today and still dark. I can turn the burners on but of course can't turn the oven on. My husband is an electrical engineer so he most likely can install what needs to be installed or do we need to buy a new oven? Thanks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 26 Answers

SOURCE: Jenn-Air electric range

I believe f3 means a bad oven sensor

Posted on Jan 09, 2008

Ad
Oceti
  • 51 Answers

SOURCE: Jenn-Air Gas Range

F1 is a bad power relay board.
F8 is a shorted meat probe alarm (probe jack or the harness to the probe jack)

Posted on Jan 18, 2008

fixyourboard
  • 310 Answers

SOURCE: Jenn-Air model #sve47600b. Today put new display

Make sure that you properly plugged in the keypad cable. There is the wide connector that brings all the keypad touches up to the display board, and there is the small 4-black wire connector that brings power to the control board.

For future reference, we repair electronic control boards at www.fixyourboard.com, maybe we can help you in the future.

Posted on Oct 08, 2009

  • 1 Answer

SOURCE: How to replace spark igniter - Jenn-Air SEG196 gas-electric range

took off the knob to the ignition system to clean and spray got onto the ignition under the dial and now the two front burners won't ignite unless I turn on one of the functional back burners then turn on the front burner. How do I repair this?

Posted on Oct 11, 2009

SOURCE: Jenn-Air SCE 30600, oven error codes F1 and Probe

An F-1 error code on your model means the element was energized when it should not have been, A shorted interconnect harness or failed power relay board.

A probe indication could be a failed meat probe jack or bad harness in a unit that has one. In a unit without a meat probe, suspect a bad board.

Both conditions would warrant bringing in a tech.

Before you do, turn off the circuit breaker fot 3 miutes and turn it back on. This will reboot the boards. If problem persists, the call a service tech.

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas is leaking out of regulator on my jennairgrill....model number 720-0062lp


DANGEROUS!!! Replace the regulator! Do NOT use until you do. (Home Depot)

Jul 10, 2012 | Jenn-Air Grilling

5 Answers

Jenn Aire Cook top


try national parts depot

or look for new knobs that matches the fit and change the broken one or all of them.

Jul 08, 2008 | Jenn-Air 30 in. CCE3401 Electric Cooktop

2 Answers

The whole stove exploded while preparing dinner. Please any idea what would cause this to happen. My husband was slightly injured. Glass was flying everywhere. The cook top is 10 years old and we purchased...


it sounds like you got a dead short under the glass top , it could be a wire that shorted or some type of bug that got into the elements , I would even open the top with out pulling the plug out of the wall ,if it is 10 years old mite not be worth fixing but it should be looked at before you decide Frank

May 10, 2011 | Jenn-Air 30 in. CCE3401 Electric Cooktop

2 Answers

My Jenn-Air dishwasher is approx 15 years old. Now all of a sudden it's leaving a white film on everything. I've tried both liquid and dry detergents as well as jet dry, running the hot water and disposer,...


it is not your dishwasher actually. it is your water. they must have changed the way they were treating it in your area. hard water leaves this white film. www.dishwasherfilter.com has a new product out exactly for this problem. it is very affordable and works amazing. you will love it guaranteed.

Aug 09, 2009 | Dishwashers

1 Answer

My oven Door fell off. it is a Jenn-Air JJW9530C


This is a known issue. The model number is JJW9530C. I have been browsing the internet trying to find stronger hinges but with no luck. It seems there are a lot of unhappy Jenn air owners. You are correct in your assumption that the door is to heavy for the hinges. I will post the websites for your review

http://www.ovensworld.com/jenn-air-jjw9530c-expressions-collection-electric-single-oven.html

Maybe if I could see the hinge I could fabricate a stronger stainless steel one for you

Apr 27, 2009 | Jenn-Air JJW9530C Stainless Steel Electric...

1 Answer

Jennair down draft cooktop


hi i have a Jenn air down draft as well you should have a spring loaded flap like a dryer they sell them
separately, you can buy them at home depot or lowes that will stop some of the cold air coming in not all of it.

Dec 14, 2008 | Jenn-Air JGR8850 Gas Kitchen Range

Not finding what you are looking for?
Jenn-Air JER8855 Electric Kitchen Range Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Kitchen Ranges Experts

Mike Carew

Level 3 Expert

969 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2183 Answers

Are you a Jenn-Air Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...