Question about Patton (HASF1016UC) Stand (Pedestal) Fan

Open Question

I have a Patton U2-20PC fan. The knob for the on/off-speed control switch is broken; I need to buy another knob. What's the part number and where do I send my money? Thank you. Bill Barry

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sonicboomele
  • 1557 Answers

SOURCE: need fan blade for patton model u2-1887

it would be far cheaper and more easy to replace the entire unit

Posted on Apr 21, 2010

  • 1 Answer

SOURCE: Where do I find a resource for a new fan blade for

i have a good blade for model #u2-1887.

Posted on Jun 14, 2010

  • 8 Answers

SOURCE: Need a source for a blade for a Patton U2-1887 fan

Try McMaster Carr -- page 640, Fans and Fan Blades.

http://www.mcmaster.com/#ventilation-fans/=8qgdv5

Posted on Sep 08, 2010

  • 2 Answers

SOURCE: Where can I buy a rotary switch for a Patton U2 1879 floor fan?

You can check with the local hardware store.

Posted on Nov 09, 2010

  • 2 Answers

SOURCE: i have a u2-1887. the speed control knob has

Check with the local hardware store

Posted on Nov 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

On/off swith knob broken


Is it the actual knob that is broken or the little tab the knob holds onto that is broken. You either need a replacement knob or a replacement switch assuming the know is also the thermostat for the unit. Does that same knob control the fan speed? Temprature or timer?

Mar 31, 2014 | Pelonis Heating & Cooling

1 Answer

I was trying to install a fan control switch on my Patton floor fan and took the 3 speed switch out and disconnected the wires and cannot figure out what wires (too many colored wires) to connect to the 2...


Thr issue you are having you need to look on the motor and see if there is a diagram but you have to use the grey and white for a capacitor because i have an older fan that has no capacitor. and use the red for high

Dec 28, 2010 | Patton U2-1487 Floor / Box Fan

2 Answers

I have a u2-1887. the speed control knob has broken off. i need a new speed control switch and knob


SAME THING HAPPENED TO MINE...THE SWITCH BROKE APART IN PIECES...WHERE CAN YOU GET ANOTHER SWITCH?

Oct 12, 2010 | Patton U2-1887HO Floor / Box Fan

2 Answers

I have 2 Hunter ceiling fans and the wall switch has 2 knobs which you push to click on or off.......after you click on...you can turn the knob and increase or decrease the fan speed. You can click on both...


Hello .. you should be able to find a replacement for your fan control at any building supply store, a home depot type store. Look or ask for a variable speed fan control. This is slightly different from a normal liight dimmer . You might also look for a replacement knob before replacing the whole switch, or matbe getting a replacement just to replace the knob ..

Jun 18, 2010 | Hunter Ceiling Fan Control Switch

3 Answers

Wiring on a 3 speed rotary switch for a fan (cord type),the switch just broken and i want make a connection on wires for just to run at only one speed.


put the 2 white wires together then try one of the other wires from the fan to the black power wire,if to slow try the other wire if that speed works tape off the other wire . it should be white to white and red to black green is ground

Sep 03, 2009 | Patton U2-1487 Floor / Box Fan

1 Answer

Floor fan has stopped working


As the manual push buttons don't work, it is possible the remote and receiver are working ok and the fault is elsewhere on the pcb and is perhaps something your local tv and radio repair shop could tackle.

The motor speed control is probably achieved by electronic rather than electrical methods and it would be more practical to repair the existing system than to attempt modification - finding a suitable 4-position switch capable of reliable operation with an inductive load of nearly 3 amps (plus safety margin) presents one problem, matching it to a method of speed control and installing it neatly and safely is quite another.

Practically speaking and considering the low cost of imported fans, such a conversion is not worth carrying out. There is a worthwhile alternative however...
In the old days there was a ready market for an easy method of controlling the speed of small electric motors and the introduction of the diac and triac and the thyristor made it possible and soon the papers and magazines filled with adverts such as "Control Drill Speeds". That was just the beginning as the success of such devices spawned a host of power controllers and dimmer switches in steps or continuously with just a single control.

You could construct such a device from one of the many available project circuits or buy a power controller ready built. A good one is not cheap but should last a long, long time.
A standard dimmer switch might handle the job but dimmer switches aren't usually suitable for an inductive load.

I hope I have provided food for thought and further research. Good luck!

May 28, 2017 | Patton Electric Dryers

1 Answer

Fan blade for a U2-20


I have a metal blade for the Patton U2-20 fan listed on ebay. The item number is 160273949463 and the listing ends on Wednesday August 27 at 10.00 p.m. I had this fan for 8 years and the motor has failed. Patton could not replace the motor since this is a discontinued item, and I figured that someone could use another blade for their fan. I hope this helps you!

Jun 27, 2008 | Patton Electric U2-20 Box Fan

Not finding what you are looking for?
Patton (HASF1016UC) Stand (Pedestal) Fan Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Patton Dryers Experts

Brad Brown

Level 3 Expert

15441 Answers

Tom Chichester

Level 3 Expert

33250 Answers

Daniel Gottlieb
Daniel Gottlieb

Level 1 Expert

11 Answers

Are you a Patton Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...