Question about NEC VT695 LCD Projector

1 Answer

I just replaced the lamp. Is there a reset proceedure for the lamp light?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

No reset other then resetting the hours in the projector's menu. This is for reference only and will not keep the projector from coming on. If the lamp will not light make sure the lamp cover is all the way on and nothing has broken off of it.

Posted on Oct 29, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Warning message for lamp replacement appears at each power up!

After replacing the lamp, make sure the lamp cover is securely closed. Select the Lamp Replacement option in the menu, (MENU > Settings > Setup menu) and follow the on-screen procedure.

Apr 20, 2017 | Sony LMP-H130 Projector Lamp Projector...

1 Answer

Picture only goes on for 1-2 seconds then goes blank with standby light flasing red 4x...was told it was the fan. Its probably dusty and would like to know how to get to it and clean it before I get ripped...

This also could mean that you need to replace the lamp. LCD displays have a lamp timer that when it reachs it max time it will not allow the unit to turn on till the lamp is replaced and the timer is reset. Check your manaul to see the proper proceedure to do this.

May 15, 2010 | Sony KDF-E50A10 50 in. LCD HDTV

1 Answer

Tv image will not show , it turns off it says ... something about the lamp inside the tvneed to be replaced?

The lamp timer on your unit has reached the max hours. it needs to be reset. There should be a reset feature in the menu. You should replace the lamp. It will brighten up your picture too. It must be done soon as once the timer reaches a limit your unit will not turn on at all. Check your manual for proper lamp type and replacement proceedure.

Feb 27, 2010 | Panasonic Televison & Video

1 Answer

I replaced my RD50's lamp recently and everything works perfectly, but the notice telling me that it is time to replace my light continues to display every time I turn the set on. There is probably a way...

There should be a reset lamp function in the service section of the menu. If there isn't, there is a way to do it by pushing and holding a sequence of buttons on the tv or remote. It varys from model to model. Check your manaul to see what the correct proceedure would be for your model.

Feb 09, 2010 | Optoma RD50 Television

1 Answer

How do you reset the hour meter on a Panasonic LCD? Lamp replaced but no instructions on resetting

From my records your Model number is not an LCD television, but I have the LCD reset proceedure listed below for you.

Panasonic Lamp timer reset.

For the full instructions and how to reset the lamp timer go to the following site

I hope this information allows you to resolve this issue.

Oct 13, 2009 | Panasonic PT-47WX49 47" Rear Projection...

1 Answer

No picture, have audio tv shuts off after 2 minutes

If you've replaced the lamp with a Mitsubishi lamp and not a generic, then the problem will be in one of two areas. Its either a bad ballast board (lamp power supply) or the color wheel assembly. If you've gotten a generic lamp, you may find that that's the reason its still not working properly. Many generic lamps are unsuitable for this product and will cause issues like low brightness, intermittent no start, and short lamp life. Also, make sure that the lamp door is properly installed because there is an interlock switch which will open if the door is not aligned properly.


Feb 14, 2009 | Mitsubishi WD-73733 73" HDTV

1 Answer

Light does not come on -- we replaced the bulb--still dark

Sounds like the lamp timer has reached it's limit. In your users manual you will find the proceedure on replacing the lamp and reseting the timer. Once this is done the projector should work.

Jan 08, 2009 | Televison & Video

10 Answers

Lamp Hour Meter

This proceedure should work for your model to reset the lamp meter.
Lamp Time Reset Procedure:
Be sure to reset the Lamp time to "0" after replacing the new
1. Plug in the AC Cord, and turn on the power by pressing the
POWER button.
2. Press and hold the VOLUME DOWN button on the unit and
the SPLIT key on the remote together for over 5 seconds
in power on condition.
When the reset is finished, the display will indicate that the lamp hrs have been reset to 0 and the LAMP LED goes out.

Mar 29, 2008 | Panasonic PT-50LC13 50" Rear Projection...

5 Answers

Lamp light

If you still need code i have it at shop i am home right If i rember right you must reset lamp Timer to Tell tv that it old lamp has been replaced with new code is 9,8,7,6, ect...........

Jan 17, 2008 | Zenith E44W46LCD 44" Rear Projection...

Not finding what you are looking for?
NEC VT695 LCD Projector Logo

988 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Office Equipment & Supplies Experts


Level 3 Expert

2237 Answers

The Knight
The Knight

Level 3 Expert

75178 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a NEC Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides